Sign in today to find solutions:

Forgot your password?

Don't have an account? Sign up

 
Integrated High Definition
LED TV/DVD Combination
User's Guide:
24V4210U
24V4260U
If you need assistance:
Toshiba's Support Web site
Call Toshiba Customer Support Center:
Within the United States at (800) 631-3811
Outside the United States at (949) 583-3050
For more information, see
Owner's Record
The model number and serial number are on the back and side of your TV.
Record these numbers in the spaces below. Refer to these numbers whenever you
communicate with your Toshiba dealer about this LED TV/DVD combination.
Model number: ______________________________________________
Serial number: _______________________________________________
Note: To display a High Definition
picture, the TV must be receiving a
High Definition signal (such as an over-
the-air High Definition TV broadcast, a
High Definition digital cable program, or
a High Definition digital satellite
program). For details, contact your TV
antenna installer, cable provider, or
support.toshiba.com
"Troubleshooting" on page 147
in this guide.
GMA300010013
4/12

Summary of Contents

  • Page 1

    The model number and serial number are on the back and side of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this LED TV/DVD combination. Model number: ______________________________________________...

  • Page 2

    Dear Customer, Thank you for purchasing this Toshiba LED TV. This manual will help you use the many exciting features of your new LED TV/DVD combination. Before operating your LED TV/DVD combination, carefully read this manual completely. WARNING To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.

  • Page 3

    Important Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

  • Page 4

    Care For better performance and safer operation of your TOSHIBA TV, follow these recommendations and precautions: 35) If you use the TV in a room whose temperature is 32° F (0° C) or below, the picture brightness may vary until the LCD warms up.

  • Page 5

    This is normal, especially when the unit is being turned on or off. If these sounds become frequent or continuous, unplug the power cord and contact a Toshiba Authorized Service Provider. WARNING: RISK OF SERIOUS PERSONAL INJURY OR...

  • Page 6

    Removing the Pedestal Stand 1) Carefully lay the front of the unit face down on a flat, cushioned surface such as a quilt or blanket. Leave the stand protruding over the edge of the surface. Note: Extreme care should always be used when removing the pedestal stand to avoid damage to the LCD panel.

  • Page 7

    Title 1 Chapter 1 Chapter 2 Chapter 1 Chapter 2Chapter 3 Video CD/Audio CD Video CD/Audio CD Track 1 Track 2 Track 3 Each title, chapter or track is assigned a number, which is called “title number”, “chapter number” or “track number”...

  • Page 8

    Because of problems and errors that can occur during the creation of DVD and CD software and/or the manufacture of DVD and CD discs, Toshiba cannot assure that this LED TV/DVD combination will successfully play every disc bearing the DVD and CD logos.

  • Page 9

    Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.

  • Page 10

    INCURRED DIRECTLY OR INDIRECTLY FROM ANY TECHNICAL OR TYPOGRAPHICAL ERRORS OR OMISSIONS CONTAINED HEREIN OR FOR DISCREPANCIES BETWEEN THE PRODUCT AND THE MANUAL. IN NO EVENT SHALL TOSHIBA BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, OR EXEMPLARY DAMAGES, WHETHER BASED ON TORT,...

  • Page 11: Table Of Contents

    Contents Chapter 1: Introduction... 18 Features ...18 Overview of installation, setup, and use...19 TV front, top, and side panel controls and connections Adjusting the screen angle...22 TV back panel connections ...22 Chapter 2: Connecting Your TV... 24 Overview of cable types ...24 Coaxial cable (F-type) ...24 Standard A/V cables (red/white/yellow) ...25 Component video cables (red/green/blue) ...25...

  • Page 12: Table Of Contents

    Contents Connecting a DVD player with ColorStream (component video)...29 Connecting a satellite receiver...30 Connecting an HDMI® or DVI device to the HDMI® input ...31 HDMI® CEC connection ...34 Connecting a digital audio system ...35 Connecting a computer...37 Connecting a computer to the TV’s PC IN terminal Connection to the TV’s HDMI®...

  • Page 13: Table Of Contents

    Favorites browser ...64 Elements of the Channel Browser ...65 Adding and clearing channels and inputs in the History List ...67 Tuning channels...67 Tuning to a specific channel (programmed or unprogrammed)...67 Tuning to the next programmed channel ...68 Switching between two channels using Channel Return...68 Switching between two channels using SurfLock™...

  • Page 14: Table Of Contents

    Contents Adjusting the audio quality...83 Audyssey Premium Television™ ...84 Audyssey ABX™ ...84 Using Audyssey Dynamic Volume® ...85 Selecting the optical audio output format ...85 Using the Dolby® Digital Dynamic Range Control Using the Locks menu ...86 Entering the PIN code ...86 Forgotten PIN code ...87 Changing your PIN code ...87 Using parental controls (for USA region)...88...

  • Page 15: Table Of Contents

    Using HDMI® CEC...108 Displaying TV status information ...112 Understanding the auto power off feature...113 Understanding the last mode memory feature ...113 Chapter 7: Using the TV’s Advanced Features ...114 Using the advanced picture settings ...114 Dynamic Contrast ...114 Static Gamma ...115 Color temperature ...115 CableClear®...

  • Page 16: Table Of Contents

    Contents Changing the scene angle (DVD) ...130 Selecting a DVD title (DVD)...130 DVD menu (DVD)...130 Sound track language/Audio channel/Subtitle...131 Selecting a sound track language (DVD)...131 Selecting the audio channel (VCD)...131 Viewing subtitles (DVD) ...131 Playback information/VCD playback control ...132 Viewing the playback info (DVD/VCD)...132 Enabling the Playback Control (PBC) function MP3, WMA, JPEG, and Audio CD operation...133 MP3/WMA/JPEG/Audio CD information...133...

  • Page 17: Table Of Contents

    Media Player problems ...152 Disc playback problems ...152 light indicator ...153 Power indicator...153 If the problem persists after trying the solutions ..153 Appendix A: Specifications... 154 Television system ...154 Channel coverage...154 Power source...155 Power maximum current ...155 Power consumption...155 Audio power...155 Speaker type ...155 Video/audio terminals ...155 Video/audio input...155...

  • Page 18: Chapter 1: Introduction, Features

    Chapter 1 Introduction Features The following are just a few of the many exciting features of your new Toshiba wide screen, integrated HD, LED TV/DVD combination: ❖ Integrated Digital Tuning (8VSB ATSC and QAM)— Eliminates the need for a separate digital converter set-top box (in most cases).

  • Page 19: Overview Of Installation, Setup, And Use

    Place the TV far enough from walls and other objects to allow proper ventilation. Inadequate ventilation may cause overheating, which will damage the TV. THIS TYPE OF DAMAGE IS NOT COVERED UNDER THE TOSHIBA WARRANTY. Do not plug in any power cords until after you have connected all cables and devices to your TV.

  • Page 20

    Introduction TV front, top, and side panel controls and connections “Learning about the remote control” on page 42 overview of the buttons on the remote control. After connecting all cables and devices, plug in the power cords for your TV and other devices. Then press the Power button on the TV control panel or remote control to turn on the TV.

  • Page 21

    TV front, top, and side panel controls and connections Remote sensor (embedded)—Point the remote control toward this remote sensor. Disc slot—Load the disc, with label facing forward, into the disc slot to view or listen. EJECT button—Press to eject the disc. VOLUME (+ -) buttons—Adjusts the volume level.

  • Page 22: Adjusting The Screen Angle, Tv Back Panel Connections

    Introduction Adjusting the screen angle Adjusting the screen angle You can adjust the angle of the TV screen 3° forward or 15° backward from a vertical angle. Hold the base of the TV while adjusting the screen. (This feature is available on select models.) (Sample Illustration) Adjusting the screen angle TV back panel connections For explanations of cable types and connections, see...

  • Page 23

    ANALOG AUDIO OUT—Analog audio outputs for connecting an audio amplifier. PC/HDMI 1 (Audio) IN—PC audio input terminal is shared with an HDMI 1 analog audio input terminal, and its use can be configured in the Audio Setup menu, see Audio” on page PC IN—Connects a personal computer.

  • Page 24: Chapter 2: Connecting Your Tv, Overview Of Cable Types, Coaxial Cable (f-type)

    Chapter 2 Connecting Your TV Overview of cable types Before purchasing cables, know the connector types your devices require. You can purchase cables from most stores that sell audio/video devices. Coaxial cable (F-type) (Sample Illustration) Coaxial cable Coaxial (F-type) cable connects your antenna, cable TV service, and/or cable converter box to the ANT/CABLE input on your TV.

  • Page 25: Standard A/v Cables (red/white/yellow), Component Video Cables (red/green/blue), Hdmi ® Cable

    Overview of cable types ® cable ® (High-Definition Multimedia Interface) cable with ® output. An HDMI “Connecting an HDMI® or DVI device to the cables provide the best audio and picture quality. Connecting Your TV ® is Toshiba’s ® cable delivers digital...

  • Page 26: Optical Audio Cable, Analog Rgb (15-pin) Computer Cable, Mm Stereo To Rca Y-cable

    Connecting Your TV Overview of cable types Optical audio cable (Sample Illustration) Optical audio cable Optical audio cable connects receivers with Dolby (pulse-code modulation) optical audio input to the TV’s Digital Audio Out terminal, see page Analog RGB (15-pin) computer cable (Sample Illustration) Analog RGB (15-pin) computer cable Analog RGB (15-pin) computer cable connects a computer to the TV’s PC IN terminal, see...

  • Page 27: Connecting A Vcr, Antenna, Or Cable Tv

    Connecting a VCR, antenna, or cable TV (Sample Illustration) Connecting to a VCR, antenna, or Cable TV Items needed: ❖ Coaxial cables ❖ Standard AV cables NOTE When you use a Cable box, you may not be able to use the remote control to program or access certain features on the TV.

  • Page 28: Connecting A Camcorder

    Connecting Your TV Connecting a camcorder Connecting a camcorder (Sample Illustration) Connecting a camcorder You will need standard A/V cables. To view the camcorder video, select the VIDEO input source on the TV.* *To select the video input source, press the INPUT button on the remote control, see NOTE The unauthorized recording, use, distribution, or revision of...

  • Page 29

    Connecting a DVD player with ColorStream Connecting a DVD player with ColorStream (component video) (Sample Illustration) Connecting a DVD player with ColorStream Items needed: ❖ Standard audio cables ❖ Component video cables ❖ You can connect the component video cables (plus audio cables) from the DVD player to the COLOR STREAM HD terminal in the TV.

  • Page 30: Connecting A Satellite Receiver

    Connecting Your TV Connecting a satellite receiver Connecting a satellite receiver (Sample Illustration) Connecting a satellite receiver Items needed: ❖ Standard audio cables ❖ Component video cables ❖ You can connect the component video cables (plus audio cables) from the DVD player to the COLOR STREAM HD terminal in the TV.

  • Page 31: Input

    Connecting an HDMI® or DVI device to the HDMI® input NOTE The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability. Connecting an HDMI ®...

  • Page 32

    Connecting Your TV Connecting an HDMI® or DVI device to the HDMI® input ❖ ® HDMI cables transfer both video and audio. Separate analog audio cables are not required (see illustration). (Sample Illustration) Connecting an HDMI To view the HDMI Select HDMI 1 or HDMI 2 video input source on the TV.* *To select the video input source, press the INPUT button on the remote control, see...

  • Page 33

    Connecting an HDMI® or DVI device to the HDMI® input ❖ 3.5mm Stereo to RCA Y-Cable ® An HDMI to DVI adapter cable transfers video only. Separate analog audio cables are required (see illustration). (Sample Illustration) DVI Device connections NOTE To ensure that the HDMI ❖...

  • Page 34: Hdmi® Cec Connection

    Connecting Your TV HDMI® CEC connection HDMI® CEC connection You can control the basic functions of connected audio/video devices using the TV’s remote control if you connect a HDMI® CEC compatible audio receiver or playback device. For an explanation of setup and operations, see device (DVD player, etc.) control”...

  • Page 35: Connecting A Digital Audio System

    ❖ This feature is limited to models incorporating Toshiba’s HDMI® CEC. However, Toshiba is not liable for those operations. For compatibility information, refer to the individual instruction manuals for your other devices that have CEC technology. NOTE This feature may not work properly depending on the devices that are connected.

  • Page 36

    Connecting Your TV Connecting a digital audio system Press the ( / press the INPUT button. (Sample Image) Audio Setup screen Press the ( / Format. Press the ( / or PCM, depending on your device. (Sample Image) Audio Setup screen - Done To save the new settings, highlight Done, and then press the OK button.

  • Page 37: Connecting A Computer

    Connecting a computer With either the PC IN or HDMI computer’s display on the TV and hear the sound from the TV’s speakers. Connecting a computer to the TV’s PC IN terminal When connecting a computer to the PC IN terminal on the TV, use an analog RGB (15-pin) computer cable and a PC audio cable.

  • Page 38

    Connecting Your TV Connecting a computer Other formats or non-standard signals will not be displayed correctly. To display the optimum picture, use the computer setting feature, “Using the PC settings feature” on page NOTE ❖ The PC audio input terminals on the TV are shared with the HDMI 1 analog audio input terminals.

  • Page 39

    Connection to the TV’s HDMI When connecting a computer with a HDMI use an adapter cable and analog audio cables. When connecting a computer with an HDMI cable (type A connector). Separate analog audio cables may not be necessary, depending on computer hardware and setup. TV back panel Computer (Sample Illustration) Connections to HDMI...

  • Page 40: Using The Remote Control, Installing Batteries, Chapter 3: Using The Remote Control

    Chapter 3 Using the Remote Control Using the remote control The remote control can operate your LED TV/DVD combination and control the basic functions of connected audio/video devices if you connect a HDMI® CEC compatible audio receiver or playback device, see “HDMI®...

  • Page 41

    Insert the batteries, corresponding to the (+) and (–) markings on the battery compartment. (Sample Illustration) Installing the batteries Replace the battery cover. Do not expose batteries to excessive heat such as sunshine, fire, etc. NOTE ❖ Be sure to use AAA size batteries. ❖...

  • Page 42: Learning About The Remote Control

    Using the Remote Control Learning about the remote control Learning about the remote control The buttons used for operating the LED TV/DVD combination are described here. For the HDMI® CEC remote control functions, see “HDMI® CEC playback device (DVD player, etc.) control” on page 108.

  • Page 43

    NOTE The error message “NOT AVAILABLE” may appear if you press a key for a function that is not available. The POWER button turns the TV On and Off. When the TV is on, the power LED indicator on the TV front glows green. The EJECT button ejects the disc from the disc slot.

  • Page 44

    Using the Remote Control Learning about the remote control The CH RTN button returns to the last viewed channel or source, see Return” on page previous directory from a Media Player sub-folder or sub-menu, see The AUDIO/MTS button selects the audio mode in ANT/CABLE source, see selects the DVD sound track language or VCD audio channel in DVD mode, see...

  • Page 45

    Learning about the remote control The STOP button stops playback of the loaded disc, see “Playing an audio file” on page The SKIP forward button skips forward to locate later DVD chapters, see “Playing an audio file” on page The SKIP reverse button skips back to locate the beginning of current DVD chapter or locate a previous chapter, see an audio file”...

  • Page 46: Main Menu Layout, Chapter 4: Menu Layout And Navigation

    Chapter 4 Menu Layout and Navigation Main menu layout The Installation menu contains the Terrestrial and System Status menus. To open the Installation menu, press the MENU button on the remote control or MENU on the TV control panel, open the Setup menu, select Installation, and then press the OK button.

  • Page 47: Menu Setup/installation/layout

    Icon Item Preferences CC Selector Base CC Mode Digital CC Settings Input Labeling AV Input Menu Language Channel Browser Setup HDMI® CEC Player Control Energy Saving Settings Locks Enable Rating Blocking Edit Rating Limits Input Lock Panel Lock GameTimer New PIN Code Setup Installation HDMI®...

  • Page 48: Navigating The Menu System

    Menu Layout and Navigation Navigating the menu system Icon Item Terrestrial Input Configuration Channel Program Channel Options Time Zone Signal Meter System Status System Information Navigating the menu system You can use the buttons on the remote control or TV control panel to access and navigate your TV’s on-screen menu system.

  • Page 49

    All menus close automatically if you do not make a selection within a few seconds, except the signal meter menu, which closes automatically after a few minutes. To close a menu instantly, press the EXIT button. NOTE The menu background may sometimes appear black, depending on the signal the TV is receiving.

  • Page 50: Initial Setup, Chapter 5: Setting Up Your Tv

    Chapter 5 Setting up your TV Initial Setup When you first turn on or reset the TV, the Initial Setup window will appear. In the Menu Language field, press the ( / Press the ( / set your desired time zone, using the ( / then press the OK button.

  • Page 51

    Menu language You can choose from three different menu language settings (English, Français, and Español). Your selection is the language all menus are displayed in. To select the menu language: Press the MENU button to open the Preferences menu, and highlight Menu Language.

  • Page 52: Storing Channels In Memory (optional), Auto Tuning

    Setting up your TV Storing channels in memory (optional) Highlight ANT/CABLE In and press the ( / to select the input source (Cable or Antenna). (Sample Image) Selecting the ANT/CABLE input source To save your new settings, highlight Done, and then press the OK button.

  • Page 53

    Storing channels in memory (optional) Highlight Installation, and then press the OK button. (Sample Image) Auto tuning program channels A new set of Installation menus appear. Open the Terrestrial menu, highlight Channel Program to open the Start Scan window, and then press the OK button to begin channel programming.

  • Page 54: Setting Channel Skip

    Setting up your TV Setting channel skip Setting channel skip To prevent a channel from being viewed, you can set it to be skipped. From the Setup menu, highlight Installation, and then press the OK button. Press the ( / then press the OK button.

  • Page 55: Setting The Hdmi® Audio Mode

    Press the ( / be locked, and then press the OK button. Enter your four-digit PIN code. A check appears in the box. To remove the check, press the OK button again. NOTE If the PIN code has not been set yet, a warning message appears. To save the setting, press the EXIT button.

  • Page 56

    Setting up your TV Setting the HDMI® audio mode Press the ( / then press the ( / mode (Auto, Digital, or Analog). (Auto is the recommended mode.) See HDMI® input” on page (Sample Image) HDMI Mode: Description: When viewing the HDMI 1 input, if digital audio from the HDMI Auto input is available, it will be output.

  • Page 57: Viewing The Digital Signal Meter, Setting The Time Zone

    Viewing the Digital Signal Meter You can view the digital signal meter in the ANT/ CABLE digital TV input source only. To view the digital signal meter: Press the MENU button to open the Setup menu. Highlight Installation, and then press the OK button. A new set of Installation menu icons appear.

  • Page 58: Viewing The System Status, Reset Factory Defaults

    Setting up your TV Viewing the system status To set the Daylight Saving Time status, press the ( / buttons to select Yes or No, highlight Done, and then press the OK button. Viewing the system status Press the MENU button to open the Setup menu. Highlight Installation, and then press the OK button.

  • Page 59: Selecting The Video Input Source, Chapter 6: Using The Tv's Features

    Chapter 6 Using the TV’s features Selecting the video input source To select the video input source to view: Press the INPUT button on the remote control or TV control panel. Choose from the following options: ❖ Press 0-5. ❖ Repeatedly press the ( / control, and then press the OK button to change the input setting.

  • Page 60

    Using the TV’s features Selecting the video input source ❖ The current signal source displays in the top right corner of the Input Selection screen. Input Selection ANT/CABLE Video/ColorStream HD HDMI 1 HDMI 2 INPUT (Sample Image) Input Selection screen NOTE ❖...

  • Page 61: Labeling The Video Input Sources

    Press the INPUT button repeatedly to highlight the desired input source, and then press the EXIT button. NOTE ❖ When selecting HDMI® CEC input sources from the pop-up window using the INPUT button, some HDMI® CEC devices may automatically turn on. ❖...

  • Page 62

    Using the TV’s features Labeling the video input sources To label the video input sources: Press the MENU button to open the Preferences menu. Highlight Input Labeling, and then press the OK button. (Sample Image) Input Labeling screen Press the ( / you wish to label.

  • Page 63: Tuning Channels Using The Channel Browser

    Tuning channels using the Channel Browser Input labeling example: The screen below left shows the default Input Selection screen (with none of the inputs labeled as a specific device). The screen below (right) is an example of how you can label the inputs if you connected a VCR to ColorStream HDMI 1, and a DVD player to HDMI 2.

  • Page 64: Favorites Browser

    Using the TV’s features Tuning channels using the Channel Browser Favorites browser The Favorites Browser allows you to quickly configure a favorite channels/inputs list that is integrated into the Channel Browser. To add a favorite channel/input: Tune to the channel or input. Press and hold the FAV button for a few seconds.

  • Page 65: Elements Of The Channel Browser

    Tuning channels using the Channel Browser Press the ( press the ( / Press the ( then press the ( / Press the ( and then press the ( / NOTE HDMI® CEC List is automatically grayed out and set to Off when Enable HDMI®...

  • Page 66

    Using the TV’s features Tuning channels using the Channel Browser Channel or input that is currently highlighted in the browser Channels stored in the History List To toggle among the available lists: After opening the Channel Browser, press the ( / to toggle through the History, ANT/CABLE, Inputs, Favorites, or HDMI®...

  • Page 67: History List, Tuning Channels

    Adding and clearing channels and inputs in the History List Adding channels and inputs to the History List: As a channel or input is tuned, the Channel Browser adds it to the History List and displays it on the right side of the Channel Browser.

  • Page 68: Tuning To The Next Programmed Channel, Return, Surflock

    Using the TV’s features Tuning channels Tuning to the next programmed channel Tuning analog channels: Press the Channel Number (0–9) buttons on the remote control. For example, to select channel 125, press 1, 2, 5, and then press the OK button.

  • Page 69: Selecting The Picture Size

    Press and hold the CH RTN button for a few seconds until the message “Memorized” appears on the screen. The channel has been programmed to the CH RTN button. You can then change channels repeatedly, and when you press the CH RTN button, the memorized channel will be tuned. The TV will return to the memorized channel one time only.

  • Page 70: Full

    Using the TV’s features Selecting the picture size To select the picture size using the menus: Select Picture Size in the Theater Settings menu. Press the ( / setting. Highlight Done, and then press the OK button. NOTE Some of the picture sizes may not be available depending on the receiving signal format (those will be “grayed out”...

  • Page 71: Theaterwide 1, Theaterwide 2, Theaterwide 3

    TheaterWide 1 This setting is for viewing in 4:3 format programs. (Sample Illustration) Picture size - TheaterWide 1 The center of the picture remains close to its original proportion, but the left and right edges are stretched horizontally to fill the screen.

  • Page 72: Native

    Using the TV’s features Selecting the picture size Native These settings are for viewing in 480i (HDMI 720p, 1080i, and 1080p signal programs). (Sample Illustration) Picture size - Native ❖ If receiving a 1080i, 1080p, 720p, 480i (HDMI ® (HDMI ) signal program, the video is scaled to display the entire picture within the borders of the screen (i.e.

  • Page 73: Normal

    Scrolling the TheaterWide® picture (TheaterWide 2 and 3 only) Normal This setting is for viewing VGA, SVGA, XGA, WXGA, and SXGA sources. (Sample Illustration) Picture size - Normal This size is a non-stretched display. Some input signal formats will display with sidebars and/or bars at the top and bottom. Dot by Dot This setting is for viewing VGA, SVGA, XGA, WXGA, and SXGA sources.

  • Page 74: Using The Auto Aspect Feature

    Using the TV’s features Using the Auto Aspect feature Highlight Theater Settings, and then press the OK button. (Sample Image) Theater settings screen In the Picture Size field, select either TheaterWide 2 or TheaterWide 3 NOTE You cannot scroll in any other mode. Press the ( Press the ( / down as needed.

  • Page 75: Selecting The Cinema Mode, Using The Freeze Feature

    Aspect Ratio of Automatic Aspect Size (automatically selected when Auto Signal Source Aspect is On) Not defined (no ID-1 The current picture size you set under, see ® data or HDMI aspect picture size” on page data) NOTE The auto aspect ratio feature is not applicable to the PC input. To turn on the auto aspect ratio feature: Press the MENU button and open the Picture menu.

  • Page 76: Adjusting The Picture, Selecting The Picture Mode

    Using the TV’s features Adjusting the picture NOTE Using the FREEZE function for any purpose other than your private viewing may be prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.

  • Page 77: Adjusting The Picture Quality

    Highlight Mode, and then press the OK button. (Sample Image) Mode screen Press the ( / (Sample Image) Mode selections screen Adjusting the picture quality You can adjust the picture quality (Contrast, Backlight, DynaLight™, Brightness, Color, Tint, and Sharpness.) to your personal preferences.

  • Page 78: Using Closed Captions

    Using the TV’s features Using closed captions ® **DynaLight : This function automatically strengthens the black coloring of dark areas in the video according to the level of darkness. To adjust the picture quality: Press the MENU button and open the Picture menu. Highlight Picture Settings, and then press the OK button.

  • Page 79

    To view captions, highlight CC1, CC2, CC3, or CC4. (CC1 displays translation of the primary language in your area.) (Sample Illustration) Viewing captions NOTE If the program or video you selected is not closed captioned, no captions will display on-screen. To view text, highlight T1, T2, T3, or T4.

  • Page 80: Digital Cc Settings, Cc Selector

    Using the TV’s features Using closed captions Digital CC settings You can customize the closed caption display characteristics by changing the background color, opacity, text size, type, edge, and color. NOTE ❖ These settings are available for digital channels only. ❖...

  • Page 81: Adjusting The Audio, Muting The Sound

    caption setting will automatically change back to the current Base CC Mode setting. You can also use the CC Selector to select digital closed caption services, if available. When such services are not available, the CC Selector presents a default list of services. If the selected service is not available, the next best service will be used.

  • Page 82: Using The Digital Audio Selector, Selecting Stereo/sap Broadcasts

    Using the TV’s features Adjusting the audio Using the digital audio selector You can use the Digital Audio Selector to conveniently switch between audio tracks on a digital channel (for those channels that have multiple audio tracks). This temporarily overrides the audio track chosen by the language option under Audio Setup, see “Selecting stereo/SAP broadcasts”...

  • Page 83: Adjusting The Audio Quality

    NOTE ❖ You can typically leave the TV in Stereo mode because it outputs the type of sound being broadcast (stereo or monaural). ❖ If the sound is noisy, select Mono to reduce the noise. To listen to an alternate language on an ATSC digital station (if available), highlight the Language field in step 3 above, and then press the ( / To listen to a second audio program on an analog station, if...

  • Page 84: Audyssey Premium Television, Audyssey Abx

    Using the TV’s features Adjusting the audio To adjust the audio quality: Press the MENU button to open the Sound menu. Highlight Audio Setup, and then press the OK button. Press the ( / to adjust (Bass, Treble, or Balance). Press the ( / ❖...

  • Page 85: Using Audyssey Dynamic Volume, Selecting The Optical Audio Output Format, Feature

    Press the ( / ABX™ field. Press the ( / Using Audyssey Dynamic Volume This feature provides a consistent sound volume between television programs, commercials, and between the loud and soft passages of movies. Press the MENU button. Select Settings, SOUND, Audyssey Premium Television, Dynamic Volume.

  • Page 86: Using The Locks Menu, Entering The Pin Code

    Using the TV’s features Using the Locks menu Highlight Audio Setup, and then press the OK button. In the Dolby either Compressed. When Standard is selected, the audio outputs with minimal compression. To save the new settings, highlight Done, and then press the OK button.

  • Page 87: Forgotten Pin Code, Changing Your Pin Code

    Press the ( screen. The Lock System screen appears if a PIN code has not been stored. (Sample Image) Lock menu - store PIN screen Press the Channel Number buttons to enter a new four-digit code, enter the code a second time to confirm, and then press the OK button.

  • Page 88: Using Parental Controls (for Usa Region)

    Using the TV’s features Using parental controls (for USA region) Press the ( then press the OK button. Press the Number buttons to enter a new four-digit code. Reenter the PIN code to confirm it. Press the OK button. The new PIN code is now active. NOTE The PIN code cannot be set to “...

  • Page 89: Downloading An Additional Rating System

    (Sample Image) Locks menu screen for other regions Press the ( and then press the OK button. Press the ( / / / button. A box with an “X” is a rating that will be blocked. As you highlight a rating, a definition for the rating appears at the bottom of the screen.

  • Page 90

    ❖ The additional rating system is not designed, transmitted or controlled by the TV or Toshiba, nor is the availability of an additional rating system determined or controlled by Toshiba. Similarly, the rating of programs in an additional rating system is not determined, transmitted or controlled by the TV or Toshiba.

  • Page 91

    Rating system Independent rating system for broadcasters: Ratings: Description and Content themes: TV-MA Mature Audience Only (This program is specifically designed to be viewed by adults and therefore may be unsuitable for children under 17. L) Crude or indecent language S) Explicit sexual activity V) Graphic violence TV-14...

  • Page 92: Displaying Ratings, Blocking Tv Programs By Canada Rating

    Using the TV’s features Using parental controls (for USA region) Indication other than rating system: Display: Description: NONE The program is rated None. (No rating appears) No rating information is provided. NOTE If you place an “X” in the box next to “None” Rated, programs rated “None”...

  • Page 93: Unlocking Programs Temporarily

    Press the ( / / / button to select the level of blocking you prefer. A box with an “X” is a rating that will be blocked. To save the new settings, highlight Done, and then press the OK button. In the Edit Rating Limits screen, highlight Done, and then press the OK button.

  • Page 94: Using The Input Lock Feature, Locking Channels

    Using the TV’s features Using the input lock feature To temporarily unlock the program: Press the MUTE button. Enter your four-digit PIN code, and then press the OK button. If the correct code is entered, the program lock mode is released and the normal picture appears.

  • Page 95: Using The Gametimer

    Press the ( / then press the OK button. The list of channels appear. (Sample Illustration) Channel options Press the ( buttons to select a channel in the lock column. Press the OK button. PIN code entry will be required to set a locked channel. NOTE If the PIN code has not yet been set, a warning message appears.

  • Page 96: Using The Panel Lock Feature

    Using the TV’s features Locking channels To cancel the GameTimer To deactivate the Input Lock once the GameTimer ❖ Set the Input Lock to Off, see page NOTE ❖ A message appears when 10 minutes, 3 minutes, and 1 minute are remaining.

  • Page 97: Using The Pc Settings Feature

    To unlock the control panel, select Off in Step 5 above or press and hold the VOLUME (–) button on the TV control panel for a few seconds until the volume icon appears. Using the PC settings feature You can view an image from a PC on the TV screen. When a PC is connected to the TV's PC IN terminal, you can use the PC Settings feature to make adjustments to the image.

  • Page 98: Setting The Pc Audio

    Using the TV’s features Using the PC settings feature NOTE The screen is disrupted momentarily while adjusting the PC settings. This is not a sign of malfunction. Mode: Description: Horizontal Position Moves the picture left/right. The adjustment range is within ±10 from center.* Vertical Position Moves the picture up/down.

  • Page 99: Using The Media Player

    Using the Media Player Using Media Player with a USB device You can enjoy photos or music contents stored on a USB storage device. Photo Viewer specifications: ❖ Data type: JPEG EXIF ver 2.1 ❖ File format: JPEG ❖ Maximum photo size: 6 MB ❖...

  • Page 100: Auto Start Function, To Open The Media Player

    Do not use a USB Hub. ❖ You must obtain any required permission from copyright owners to use copyright content. Toshiba cannot and does not grant such permission. ❖ Depending on the file size and amount in your USB storage device, it may take some time for loading to view.

  • Page 101: Viewing Photo Files

    Press the ( / OK button. The Media Player menu will appear. When you select No, nothing happens. (Sample Image) Media Player - open screen NOTE ❖ The prompt will disappear after about 10 sec. ❖ If Auto Start is set to off, you can start the Media Player manually.

  • Page 102: Single View

    Using the TV’s features Using the Media Player This view allows you to search for photos in a grid format. These pictures are displayed using thumbnail data in each image file. (Sample Image) Media Player - photos screen Press the ( / / / one window.

  • Page 103: Slide Show, Playing Music Files

    Slide show This view allows you to watch a slide show of the photos. In this mode, only files located in the selected directory will be played. To start slide show, press the OK button to select Single View mode. Press the ( / photo.

  • Page 104: Viewing Photo Files And Playing Music Files At The Same Time

    Using the TV’s features Using the Media Player NOTE ❖ If playback finishes before the STOP button is pressed, the next file automatically starts to play from the beginning. ❖ Depending on the file size, it may take some time for playback to begin.

  • Page 105

    Contents Description Photo Photo list (Multi View) Sorting To sort the folders and files: 1 Press the MENU button to open the Quick Menu from Multi View mode. 2 Press the ( / 3 Press the ( / New, or Old to set the sorting rule. Title-File sorting rules: 1 Unicode priority 2 (0, 1-9), capital alphabet...

  • Page 106: Setting The Sleep Timer

    Using the TV’s features Setting the sleep timer Contents Description Music Music list (Multi View) Sorting To sort the folders and files: 1 Press the MENU button to open the Quick Menu. 2 Press the ( / 3 Press the ( / New, or Old to set the sorting rule.

  • Page 107: Automatic Power Down

    Press the Number buttons to enter the length of time (maximum of 12 hours) and then press the OK button. Or press the ( / 10-minute increments, (maximum of 12 hours). NOTE If a power failure occurs, the sleep timer setting may be cleared. To display the time remaining until the TV turns off, press the SLEEP button.

  • Page 108: No Signal Power Down, Using Hdmi® Cec

    Using HDMI® CEC This is a new feature that uses CEC technology and allows you to control Toshiba HDMI® CEC compatible devices from the TV remote control via an HDMI When the Enable HDMI® CEC in the HDMI® CEC Setup menu is set to On, the following HDMI®...

  • Page 109

    Button: Description: SKIP Reverse Skip backward Fast forward Rewind/reverse Navigates menu options / / / Enters menu options CANCEL Return to the previous menu NOTE These functions depend on the devices connected. HDMI® CEC Player Control menu functions: Press the MENU button, and then open the Preferences menu. Highlight HDMI®...

  • Page 110

    Using the TV’s features Using HDMI® CEC NOTE These functions depend on the devices that are connected. The HDMI® CEC Player Control item will be grayed out in the following conditions: ❖ A non-HDMI ❖ The Enable HDMI® CEC item is set to Off. ❖...

  • Page 111

    Other HDMI® CEC functions When the Enable HDMI® CEC and each item in the HDMI® CEC Setup menu are set to On, the following functions will be enabled. Item: Description: TV Auto Input If a connected HDMI Switch automatically switch to the appropriate HDMI TV Auto Power If a HDMI®...

  • Page 112: Displaying Tv Status Information

    Using the TV’s features Displaying TV status information To save the new settings, highlight Done and press the OK button. To revert to the factory defaults, highlight Reset and press the OK button. Displaying TV status information To display TV status information: ❖...

  • Page 113: Understanding The Auto Power Off Feature, Understanding The Last Mode Memory Feature

    NOTE The location of the banner can be moved to the top or bottom of the screen by pressing Understanding the auto power off feature The TV will automatically turn itself off after approximately 15 minutes if it is tuned to a vacant channel or a station that completes its broadcast for the day.

  • Page 114: Using The Advanced Picture Settings, Dynamic Contrast, Chapter 7: Using The Tv's Advanced Features

    Chapter 7 Using the TV’s Advanced Features Using the advanced picture settings Dynamic Contrast Dynamic Contrast detects changes in picture quality that affect the appearance of your contrast settings and then automatically adjusts the video. To select Dynamic Contrast preference: From the Picture menu, highlight Picture Settings and press the OK button.

  • Page 115: Static Gamma, Color Temperature

    Press the ( / Off. Static Gamma The static gamma feature lets you adjust the levels of black in the picture. To adjust the static gamma settings: Press the MENU button to open the Picture menu. Highlight Picture Settings, and then press the OK button. Highlight Advanced Picture Settings, and then press the OK button.

  • Page 116: Cableclear® Digital Noise Reduction

    Using the TV’s Advanced Features Using the advanced picture settings Highlight Picture Settings, and then press the OK button. Highlight Advanced Picture Settings, and then press the OK button. Highlight Color Temperature, and then press the OK button. In the Color Temperature field, press the ( / buttons to select the mode you prefer (Cool, Medium, or Warm).

  • Page 117: Mpeg Noise Reduction, Using The Game Mode Feature

    NOTE ❖ If the current input is ANT/CABLE or VIDEO, the menu will display the text “CableClear”. The available selections are Off, Low, Middle, and High. ❖ If the current input is ColorStream menu will display the text “DNR”. The available selections are Off, Low, Middle, and High.

  • Page 118

    Using the TV’s Advanced Features Using the advanced picture settings NOTE To use the Game Mode feature, the current video input must be Video, ColorStream cannot be turned on when any other video input, other than the above mentioned is selected. To turn on Game Mode: Press the MENU button to open the Picture menu.

  • Page 119: Disc Playback, Basic Playback (dvd/vcd/cd), Chapter 8: Basic Disc Playback

    Chapter 8 Basic Disc Playback Disc playback This section shows you the basics on how to play a disc. Basic playback (DVD/VCD/CD) Press the POWER button on the TV control panel or on the remote control. The Power LED on the front of the LED TV/DVD combination changes to green.

  • Page 120

    Basic Disc Playback Disc playback Press the TV/DVD button on the remote control to switch to DVD mode. The DVD start-up screen appears. (Sample Image) DVD start-up screen Hold the disc by its edges and load it in the disc slot with the label side facing forward.

  • Page 121: Removing A Disc, Disc Playback Reminders

    Higher quality picture: High resolution pictures on some discs may occasionally cause noise on the picture display. If this is the case, reduce the Sharpness setting under the Picture Settings menu. NOTE ❖ Keep your fingers well clear of the disc slot when a disc is loading or unloading.

  • Page 122: Playback Navigation

    Basic Disc Playback Playback navigation ❖ When you load a disc with the playback side facing backward, the message, “Loading” appears on the screen. It will be replaced by the message, “Incorrect Disc.” Eject the disc and load it again making sure the playback side is now facing forward.

  • Page 123: Playing Frame By Frame (dvd/vcd), Playing In Slow Motion (dvd/vcd)

    Playing frame by frame (DVD/VCD) Press the PAUSE button during playback. Each time you press the PAUSE button, the picture advances one frame. To resume normal playback, press the PLAY button. NOTE The sound is muted during frame by frame playback. Playing in slow motion (DVD/VCD) Press the SLOW button during playback.

  • Page 124: Zoom Function/scene Navigation, Using Zoom (dvd/vcd), Chapter 9: Advanced Disc Playback

    Chapter 9 Advanced Disc Playback Zoom function/Scene navigation You can change the viewing scale of a picture by using the Zoom function. Once the image has been rescaled, use the ( / / / arrow) buttons to pan the image. Scene navigation options differ depending on the kind of disc.

  • Page 125: Locating A Specific Scene

    NOTE ❖ You can use the Pause, Slow and Search playback functions in Zoom mode. ❖ Zoom function may not apply to some discs. Locating a specific scene Press the JUMP button during playback, still or stop mode. (Sample Image) Disc Jump - Title Press the ( / (Sample Image) Disc Jump - Chapter Use the Channel Number buttons (0-9) to enter a value for the...

  • Page 126: Scene Bookmark

    Advanced Disc Playback Scene bookmark VCD mode: (Sample Image) Disc Jump - VCD mode CD mode: (Sample Image) Disc Jump - CD mode NOTE ❖ When you use title navigation, playback starts from the first chapter of the selected title. ❖...

  • Page 127: Bookmarking A Scene (dvd/vcd)

    Bookmarking a scene (DVD/VCD) During playback, press the MARKER button at the scene you would like to place the bookmark. (Sample Image) Disc scene bookmarking Press the ( / then press the PLAY button. Repeat these steps to save twelve more bookmarks.

  • Page 128: Viewing A Scene Bookmark (dvd/vcd), Repeat Playback/a-b Repeat, Enabling Repeat Playback (dvd/vcd)

    Advanced Disc Playback Scene bookmark Viewing a scene bookmark (DVD/VCD) Press the MARKER button to open the bookmark window. Press the ( / (Sample Image) Disc scene bookmarking Press the PLAY button to start playback on the scene saved in the selected bookmark.

  • Page 129: Enabling A-b Repeat Mode (dvd/vcd/cd)

    The LED TV/DVD combination automatically starts repeat playback after finishing the current title or chapter. (Sample Image) Disc enabling repeat playback VCD: ❖ Press the PLAY MODE button repeatedly to select a repeat mode. The modes are listed by Track, All, or Off. (Sample Image) Disc enabling repeat playback NOTE If you set the repeat mode during stop mode, press the PLAY button...

  • Page 130: Scene Angle/title Selection/dvd Menu, Changing The Scene Angle (dvd), Selecting A Dvd Title (dvd)

    Advanced Disc Playback Scene angle/Title selection/DVD menu To resume normal playback, press the REPEAT A-B button until "A-B repeat" disappears on the screen. NOTE ❖ In some cases, subtitles for the repeated scene may not display. ❖ The A-B repeat mode may not apply to some DVD scenes. ❖...

  • Page 131: Sound Track Language/audio Channel/subtitle, Selecting A Sound Track Language (dvd), Selecting The Audio Channel (vcd)

    Sound track language/Audio channel/Subtitle Press the ( / / / item, and then press the OK or PLAY button to access it. Use the same buttons to enable an option for the selected item. Repeat this step to configure other menu options. Press the DVD MENU button again to resume playback on the scene that was playing when you pressed the DVD MENU button.

  • Page 132: Playback Information/vcd Playback Control, Viewing The Playback Info (dvd/vcd)

    Advanced Disc Playback Playback information/VCD playback control To disable subtitles: Press the SUBTITLE button until Off appears. NOTE ❖ Not all DVDs have encoded subtitles. ❖ The subtitle selection may revert to the default language when you stop playback and try to play the DVD again. ❖...

  • Page 133: Mp3, Wma, Jpeg, And Audio Cd Operation, Mp3/wma/jpeg/audio Cd Information

    Use of DVD/CD-RW discs for recording MP3 files is not recommended. You must obtain any required permission from copyright owners to download or use copyrighted content. Toshiba can not and does not grant such permission. MP3/WMA/JPEG/Audio CD information MP3/WMA/JPEG CD playback reminders ❖...

  • Page 134

    Advanced Disc Playback MP3, WMA, JPEG, and Audio CD operation ❖ Refrain from making too many sub-folders. ❖ It may take more than one minute for this LED TV/DVD combination to read MP3, WMA, and JPEG files depending on the disc structure. ❖...

  • Page 135: About The File Browser

    MP3, WMA, JPEG, and Audio CD operation ❖ WMA: ❖ File format: WMA version 7 or 8 ❖ Sampling frequency: 32 kHz/48 kbps, 44.1 kHz/48 to 92 kbps, 48 kHz/128 to 192 kbps A file recorded in mono (48 kHz/48 kbps) is not supported by this LED TV/DVD combination.

  • Page 136: Playing An Audio File

    Advanced Disc Playback MP3, WMA, JPEG, and Audio CD operation Viewing image files in thumbnail mode: You can change the browsers view mode from list mode to thumbnail mode. This is convenient when browsing for JPEG files. Press the DVD MENU button during JPEG playback. Press the ( / / / Press the OK button to play the image file.

  • Page 137: Viewing A Jpeg File

    MP3, WMA, JPEG, and Audio CD operation Press the PLAY button or the OK button to start playback. To stop playback, press the STOP button. NOTE ❖ If the current directory has more than eight files, press the ❖ To see folder contents, select a folder and then press the OK button.

  • Page 138: Viewing A Slide Show

    Advanced Disc Playback MP3, WMA, JPEG, and Audio CD operation Viewing a slide show If there are multiple JPEG files in the selected directory, you can view them in a slide show. The instructions on how to enable the slide show feature and set the interval period between pictures are listed below.

  • Page 139: Enabling Repeat Playback

    MP3, WMA, JPEG, and Audio CD playback modes NOTE ❖ The Rotate mode is available in regular JPEG viewing and slide show modes. ❖ The A-B repeat mode is not available when viewing JPEG images. ❖ During a slide show, the interval time between images may increase if the file size is too big.

  • Page 140: Programming The Playback Sequence

    Advanced Disc Playback MP3, WMA, JPEG, and Audio CD playback modes Programming the playback sequence In the file browser, press the MARKER button to open the file list (Sample Image) Programming the playback sequence NOTE You can not select the same file twice or more. A JPEG file cannot be added to a playlist.

  • Page 141: Customizing Disc Playback

    Press the MARKER button, The programmed files appear in the Playlist. (Sample Image) Programming the playback sequence In the programmed file list, press the ( / select a file, and then press the PLAY button to start playback. To remove a file from the programmed list: In the Playlist, press the ( / you wish to remove, and then press the CANCEL button.

  • Page 142

    Advanced Disc Playback Customizing disc playback Press the ( / press the ( The first setup option is highlight. (Sample Image) Configuring disc playback settings Press the ( / wish to customize. Press the ( available option settings. Press the ( / then press the OK button to apply and save the setting.

  • Page 143: Disc Playback Setup

    Disc playback setup Option OSD Language Selects the language for the setup screen display. 145 Audio Language Disc Menu Subtitle Default Downmix Parental Preference Password Spdif Output NOTE These setup settings are retained in the LED TV/DVD combination’s memory. It remains active even if the power is turned off. (Sample Image) Playback settings OSD Language Select the language for the DVD and Setup menu display.

  • Page 144

    Advanced Disc Playback Customizing disc playback The selected language will be heard or seen. (Sample Image) Playback settings (Sample Image) Playback settings Parental A DVD is usually encoded with a rating level to indicate the recommended audience age. You have the option to select the content rating level allowed for playback in your LED TV/DVD combination.

  • Page 145

    NOTE ❖ The Parental rating levels correspond to the US movie ratings. Level 1 – Kids Safe Level 2 – G Level 3 – PG Level 4 – PG–13 ❖ Some discs may not have their rating level encoded on the disc though it’s indicated on the disc jacket.

  • Page 146

    Advanced Disc Playback Customizing disc playback Use the Channel Number buttons (0–9) to input the current password. If the password has not been set yet, key in “0000.” This is the factory default password. Use the Channel Number buttons (0–9) to input the new password.

  • Page 147: General Troubleshooting, Chapter 10: Troubleshooting

    Chapter 10 Troubleshooting General troubleshooting Before calling a service technician, review this chapter or visit the Toshiba technical support Web site at causes/solutions for the problem you are experiencing. Before you begin to troubleshoot any problem, first unplug the TV from the AC wall outlet, wait approximately one minute, and then plug the TV back into the AC wall outlet.

  • Page 148: Picture Problems

    Troubleshooting Picture problems Other problems. If your TV’s problem is not addressed in this Troubleshooting chapter or the recommended solution has not worked, use the Reset Factory Defaults procedure, see page TV will not turn on. Ensure the power cord is plugged in properly, and then press the POWER button.

  • Page 149: Sound Problems

    Video Input Selection problems. If the Input Selection window does not appear when you press INPUT on the remote control or TV, press INPUT a second time. This will cause a change to the next video input source and display the Input Selection window.

  • Page 150: Remote Control Problems, Channel Tuning Problems

    Troubleshooting Remote control problems If you hear no sound, try setting the MTS feature to Stereo mode, “Using the MTS button” on page If you are not receiving a second audio program from a known SAP source, make sure the MTS feature is set to SAP mode, see “Selecting stereo/SAP broadcasts”...

  • Page 151: Closed Caption Problems, Rating Blocking (v-chip) Problems, No Hdmi® Cec Operation, Hdmi® Problems

    The V-Chip feature is available for U.S. V-Chip systems only, see “Using parental controls (for USA region)” on page No HDMI® CEC operation The HDMI® CEC feature is available for Toshiba HDMI® CEC compatible devices. Ensure that HDMI When the connected HDMI® CEC device does not work correctly after you have changed device’s settings, turn off your TV and...

  • Page 152: Media Player Problems, Disc Playback Problems

    Troubleshooting Media Player problems ® Legacy HDMI Some legacy HDMI ® HDMI TV products, due to new standard adoption. Media Player problems Incorrect functionality may occur when using a USB HUB connection. Photo files that were processed and edited using the computer’s application software may not be viewable.

  • Page 153: Light Indicator, Power Indicator, If The Problem Persists After Trying The Solutions

    The Power indicator glows green when the TV power is On. If the problem persists after trying the solutions Contact Toshiba at: Toshiba’s Support Web site: support.toshiba.com. For technical support, call the Toshiba Customer Support Center: Within the United States, at 800-631-3811 Outside the United States, at 949-583-3050 Troubleshooting light indicator 131.

  • Page 154: Television System, Channel Coverage, Appendix A: Specifications

    Appendix A Specifications NOTE ❖ These models comply with the specifications listed below. ❖ Designs and specifications are subject to change without notice. ❖ These models may not be compatible with features and/or specifications that may be added in the future. Television system NTSC standard ATSC standard...

  • Page 155: Power Source, Power Maximum Current, Power Consumption, Audio Power, Speaker Type, Video/audio Terminals, Video/audio Input

    Power source 120 V AC, 60 Hz Power maximum current 24V4210U 0.65 A 24V4260U 0.65 A Power consumption 24V4210U 0.65 A (maximum current) 0.2W (Standby mode) 0.65 A (maximum current) 24V4260U 0.2W (Standby mode) Audio power 24V4210U 5W + 5W...

  • Page 156: Colorstream® (component Video) Hd Input

    Specifications Video/audio terminals ® ColorStream (component video) HD input Video Y: 1V(p-p), 75 ohm, negative sync. Y: 1V(p-p), 75 ohm, negative sync. PB: 0.7 V(p-p), 75 ohm Suggested formats: 1080i, 720p, 480p, 480i Audio 200 mV(rms) (-20dBFS, 47K ohm or greater)

  • Page 157: Hdmi® Input, Digital Audio Output, Pc Input, Dvd/cd Player, Dimensions, Mass (weight), Operating Conditions

    PC input 15-Pin D-sub Analog RGB DVD/CD player Signal system NTSC Supported disc size 12 cm Pickup mechanism 1-lens, 2-beams Dimensions Width Height 24V4210U Depth Width Height 24V4260U Depth Mass (weight) 24V4210U 13.2 lbs (6.0 kg) 24V4260U 13.2 lbs (6.0 kg)

  • Page 158: Supplied Accessories, Acceptable Signal Formats For Pc In, Hdmi, Pc In Signal Formats

    Specifications Supplied accessories Supplied accessories ❖ Remote control with two size “AAA” batteries ❖ Resource Guide ❖ Quick Start Guide ❖ Pedestal stand ❖ Warranty Acceptable signal formats for PC IN, HDMI PC IN signal formats NOTE Depending on the connected PC, the following status may occur; incorrect display, false format detection, picture position failure, blur, or judder.

  • Page 159

    Acceptable signal formats for PC IN, HDMI® Format Resolution V. Frequency 480i 720 x 480i 59.940 Hz 480p 720 x 480p 59.940 Hz 720p 1280 x 720p 60.000 Hz 1080i 1920 x 1080i 60.000 Hz 24.000 Hz 1080p 1920 x 1080p 60.000 Hz NOTE ❖...

  • Page 160: Appendix B: License Agreement

    Some of the software components distributed under EULAs are made available for use by the user on the premise that they are not copyrighted or warranted by TOSHIBA or any third party. These software components are licensed to the user free of charge and therefore not covered by any warranty within the scope of the applicable laws.

  • Page 161

    (English) as exactly written by the respective parties other than TOSHIBA. For at least three (3) years from the date of distribution of the this product, Toshiba will give to anyone who contacts Toshiba Consumer Solutions at (800) 631-3811, for a charge of no...

  • Page 162

    License Agreement (3) Permission for use of this software is granted only if the user accepts full responsibility for any undesirable consequences; the authors accept NO LIABILITY for damages of any kind. These conditions apply to any software derived from or based on the IJG code, not just to the unmodified library.

  • Page 163

    This license was inspired by the BSD, Artistic, and IJG (Independent JPEG Group) licenses, which all encourage inclusion and use of free software in commercial and freeware products alike. As a consequence, its main points are that: ❖ We don't promise that this software works. However, we will be interested in any kind of bug reports.

  • Page 164: Index

    Index advanced picture settings CableClear® digital Noise Reduction 116 Color temperature 115 Dynamic Contrast 114 Game Mode feature 117 MPEG Noise Reduction 117 Static Gamma 115 using 114 audio adjusting quality 83 Audyssey ABX™ 84 Dolby® Digital Dynamic Range Control 85 MTS button 83 muting sound 81 optical audio output format 85...

  • Page 165

    tuning channels 63 Channel Return switching between two channels channels auto tuning 52 locking channels 94 skipping 54 specific channel 67 storing in memory 52 cinema mode selecting 75 closed captions CC selector 80 Digital CC settings 80 using 78 computer setting the audio 98 using with the TV 97...

  • Page 166

    Index chapter or track 123 fast reverse, fast forward 122 frame by frame 123 slow motion 123 Elements 65 factory defaults reset 58 favorites browser 64 features 18 Freeze feature 75 GameTimer® using 95 HDMI® audio mode setting 55 HDMI®-CEC additional functions 111 using 108 volume/mute controls 110...

  • Page 167

    57 timer sleep timer 106 troubleshooting 147 channel tuning problems 150 closed caption problems 151 contact Toshiba 153 disc playback problems 152 HDMI® 151 light indicator 153 media player problems 152 No HDMI®-CEC operation 151 picture problems 148...

  • Page 168

    Index TV panel controls front 20 left side 20 side 20 TV remote functionality 42 install batteries 40 TV remote control using 40 TV status information show 112 video input source selecting 59 video input sources labeling 61...

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: