Related Manuals for Ricoh Prinect DFE
Summary of Contents for Ricoh Prinect DFE
- Page 1 Prinect DFE Machine Code: M525/M526 Field Service Manual Ver 1.0 Latest Release: February, 2018 Initial Release: February, 2018 (c) 2018 Ricoh Co.,Ltd.
- Page 3 Important Safety Notices Warnings, Cautions, Notes In this manual, the following important symbols and notations are used. A Warning indicates a potentially hazardous situation. Failure to obey a Warning could result in death or serious injury. A Caution indicates a potentially hazardous situation. Failure to obey a Caution could result in minor or moderate injury or damage to the machine or other property.
- Page 4 Safety Prevention of Physical Injury Before disassembling or assembling parts of the machine and peripherals, make sure that the machine and peripheral power cords are unplugged. The plug should be near the machine and easily accessible. Note that some components of the machine and the paper tray unit are supplied with electrical voltage even if the main power switch is turned off.
- Page 5 18. When using a vacuum cleaner around the machine, keep others away from the cleaner, especially small children. 19. For machines installed with the anti-tip components: The anti-tip components are necessary for meeting the requirements of IEC60950-1, the international standard for safety. The aim of these components is to prevent the products, which are heavy in weight, from toppling as a result of people running into or leaning onto the products, which can lead to serious accidents such as persons becoming trapped under the product.
- Page 6 with the manufacturer’s instructions. Handling Toner Work carefully when removing paper jams or replacing toner bottles or cartridges to avoid spilling toner on clothing or the hands. If toner is inhaled, immediately gargle with large amounts of cold water and move to a well- ventilated location.
- Page 7 Laser Safety The Center for Devices and Radiological Health (CDRH) prohibits the repair of laser-based optical units in the field. The optical housing unit can only be repaired in a factory or at a location with the requisite equipment. The laser subsystem is replaceable in the field by a qualified Customer Engineer. The laser chassis is not repairable in the field.
- Page 9 Symbols, Abbreviations This manual uses several symbols and abbreviations. The meaning of those symbols and abbreviations are as follows: Symbol What it means Clip ring Screw Connector Clamp E-ring Flat Flexible Cable Timing Belt Short Edge Feed Long Edge Feed Black Cyan Magenta...
- Page 10 Trademarks Adobe, PostScript, PostScript 3, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. DIC and COLOR GUIDE are registered trademarks of DIC Corporation. Firefox is a registered trademark of the Mozilla Foundation. Google and Chrome browser are trademarks of Google Inc.
- Page 11 Microsoft® Windows® 10 Enterprise Microsoft® Windows® 10 Education The product names of Windows Server 2008 are as follows: Microsoft® Windows Server® 2008 Standard Microsoft® Windows Server® 2008 Enterprise The product names of Windows Server 2008 R2 are as follows: Microsoft®...
-
Page 13: Table Of Contents
Table of Contents Differences ............................2 Differences between TotalFlow Print Server R-62/R-62A and Prinect DFE .......... 2 Installation Flow Chart (For Prinect DFE) ....................3 Machine Installation (Differences) ......................4 Connector/ Front Panel ........................4 Unit Removal (Differences) ........................6 HDD .............................. -
Page 14: Differences
1.Differences 1. Differences Differences between TotalFlow Print Server R-62/R-62A and Prinect DFE The following are the differences between TotalFlow Print Server R-62/R-62A and Prinect DFE*: The Prinect DFE has a graphic board, USB board, and an additional HDD. ... -
Page 15: Installation Flow Chart (For Prinect Dfe)
1.Differences Installation Flow Chart (For Prinect DFE) First install the printer (Versafire CV/ Versafire CP). Then install Prinect DFE. Recommended installation steps are as follows:... -
Page 16: Machine Installation (Differences)
1.Differences Machine Installation (Differences) Connector/ Front Panel Prinect DFE for Versafire CV Name Name Power connector USB port x4 (VM support) Monitor ports USB port for power interlock (not used) USB port (keyboard) Power interlock switch (not used) USB port (mouse) - Page 17 1.Differences Prinect DFE for Versafire CP Name Name Power connector USB port x 4 (VM support) Monitor ports Power interlock switch (not used) USB port (keyboard) Data Transfer Unit ports USB port (mouse) Optical disc drive USB port (backup) Disc eject button...
-
Page 18: Unit Removal (Differences)
1.Differences Unit Removal (Differences) The print server has four HDDs. One is for the operating system [A], the other two are for data storage [B] and the other one is for VM support [C]. HDD (for VM Support) Remove the left cover. Remove the power cord [A] and SATA cable [B] from the HDD (for VM support). -
Page 19: Graphic Board
1.Differences Remove the HDD [A]. (hook ×4) Windows VM and Prinect software are not installed in an HDD spare part that is used for replacement. Heidelberg’s service representative must install this software after replacing the HDD. Graphic Board Do not touch the terminal part of the graphic board. -
Page 20: Usb Board
1.Differences Push the flat spring [A] to open the rear cover [B]. Remove the graphic board [A]. ( ×1) USB Board Do not touch the terminal part of the USB board. Clean with alcohol if you touched the terminal. Remove the left cover. - Page 21 1.Differences Lay down the machine. Push the flat spring [A] to open the rear cover [B]. Remove the USB board [A].
-
Page 22: Dimm
1.Differences DIMM Do not touch the terminals of the DIMM. Clean with alcohol if you touched the terminals. Remove the left cover. Lay down the machine. Lift the CPU fan bracket. ( x 1) - Page 23 1.Differences Open both sides of the lever, and pull out the DIMMs (×4) [A] from the sockets. When installing, gently slide the DIMM straight down into the socket and push it into the slot. Make sure that the levers close securely around the ends of the DIMM. ...
-
Page 24: Block Diagram And Functions (For Prinect Dfe)
1.Differences Block Diagram and Functions (for Prinect DFE) Block Diagram Prinect DFE for Versafire CV... -
Page 25: Functions
1.Differences Prinect DFE for Versafire CP Functions Network Cable requirements: 10BaseT (Ethernet): Unshielded Twisted Pair (UTP), Category 3 or higher 100BaseTX (Fast Ethernet): UTP, Category 5 or higher (4-pair/8-wire, short-length) 1000BaseT (Gigabit Ethernet): UTP, Category 5e or higher (4-pair/8-wire, short-length) RDTU Board Performs as an interface* between the print server and the printer. - Page 26 1.Differences Motherboard CPU: 3.4 GHz SDRAM: 16 GB (2,133 MHz DDR4) × 4, Total 64 GB Performs a self-diagnosis by BIOS and displays the error code on the digital display board (7- segment). Digital Display Board Displays the status of the print server in a 7-segment display. USB Dongle Stores product information such as a license.
- Page 27 1.Differences Graphic Board (for VM support) Sapphire Radeon HD5450 1G DDR3 PCI-E Up to 2,560 × 1,600 32bpp 60Hz VM pass-through capable USB Board (for VM support) Sunix USB4300NS USB 3.0 ports × 4...
-
Page 28: Specifications (For Prinect Dfe)
1.Differences Specifications (for Prinect DFE) General Specifications Prinect DFE for Versafire CV Item Description 6th Gen Core i7-6700 3.4GHz Memory 64 GB (16 GB ×4) SATA connection 1TB 3.5 inch HDD (7,000rpm) ×4 DVD Drive SATA connection DVD-ROM drive Interface Gigabit Ethernet ×2 (100BASE-TX/10BASE-T/1000BASE-T), USB2.0 Type-A x... - Page 29 1.Differences Item Description Built-in Fonts Roman PS font: 138 fonts Power Source 100-240 V, 3.9 A, 50/60MHz Power 400 W Consumption Dimensions (W x 193 × 525.3 × 424 mm (7.6 × 20.7 × 16.7 inches) D x H) Weight Approximately 17 kg (37.5 lbs.)