Philips 37PF9631D/37 Service Manual page 101

8.4 Option Settings
8.4.1 Introduction
The microprocessor communicates with a large number of I
ICs in the set. To ensure good communication and to make
digital diagnosis possible, the microprocessor has to know
which ICs to address. The presence / absence of these specific
ICs (or functions) is made known via the option codes.
8.4.2 Dealer Options
Table 8-3 Dealer options
Menu item Subjects
Personal Options Picture Mute
Virgin Mode
2CS Korea (only for AP
region)
Self learning TV
8.4.3 (Service) Options
Select the sub menu's to set the initialization codes (options).
Table 8-4 Options
Menu-item Subjects
PIP/DS Dual Screen
Data EPG
RRT
Display Screen
Scanning Backlight
Dimming Backlight
Video Repro Picture Processing
Combfilter
Ambient Light
MOP
POD
Source Selection HDMI 1
HDMI 2
USB version
IEEE1394
Ethernet
SPDIF inputs
Audio Repro Subw. Internal Present
Acoustic System (Cabinet design,
used for setting dynamic audio
parameters).
Miscellaneous Alternative Tuner
Tuner Type
Hotel mode
Opt. no. Group 1
Group 2
Store
8.4.4 Opt. No. (Option numbers)
Select this sub menu to set all options at once (expressed in
two long strings of numbers).
An option number (or "option byte") represents a number of
different options. When you change these numbers directly,
you can set all options very quickly. All options are controlled
via eight option numbers.
When the NVM is replaced, all options will require resetting. To
be certain that the factory settings are reproduced exactly, you
2
C
Options Description
On Picture mute active in case no picture detected
Off Noise in case of no picture detected
On TV starts up (once) with a language selection menu after the Mains switch is turned "on" for the first time (virgin mode)
Off TV does not start up (once) with a language selection menu after the Mains switch is turned "on" for the first time (virgin
mode)
Off
Off
Options
One tuner dual screen
Off
Yes / No
"Value"
On / Off
On / Off
No Spider
None / 2D / 3D
Off / Stereo
On / Off
Off
None
With analogue audio
Without analogue audio
None
1.1
Not present
Off
None
Yes / No
None
Others
ME6 2K6
Philips
TD1336S
Off
Alignments EJ2.0U LA
Notes:
• After changing the option(s), save them by pressing the OK
button on the RC before the cursor is moved to the left,
select STORE in the SAM root menu and press OK on the
RC.
• The new option setting is only active after the TV is
switched "off" and "on" again with the Mains switch (the
NVM is then read again).
Description
DS with one tuner
Feature not present
Parental control is enabled via the Regional Rating Table (RRT)
Used screen size, type, and resolution (see table "Display code overview" in chapter "Service
Modes"for the values)
Feature present / not present
Feature present / not present
Feature not present
Only selectable with Columbus in set: No/without RAM/with RAM
Off / Two inverters stereo
Feature present / not present (for sets with AmbiLight this is "on")
no POD implemented
No HDMI
DVI
HDMI
No HDMI
USB 1.1 in side I/O panel
Connector not present
Connector not present
No connector present
Internal sub woofer present / not present
n.a.
n.a.
for this set
Tuner brand
Tuner type
xxxxx xxxxx xxxxx xxxxx (see set sticker)
xxxxx xxxxx xxxxx xxxxx (see set sticker)
must set both option number lines. You can find the correct
option numbers on a sticker inside the TV set.
Example: The options sticker gives the following option
numbers (depending on the model):
• 00016 00006 00033 14979
• 01035 00000 04768 00000
The first line (group 1) indicates hardware options 1 to 4, the
second line (group 2) indicates software options 5 to 8.
8. EN 101