Boss SP-505 Owner's Manual page 37

DSP EFFECTS
13. OVERDRIVE
Mildly distorts the sound.
14. FUZZ
Adds harmonics and distorts the
sound.
15. WAH
Produces a "wah" effect
16. OCTAVE
Adds sound octaves lower.
17. COMPRESSOR
Makes the volume more consis-
tent.
18. EQUALIZER
Adjusts the volume level for
each individual frequency
range.
19. LO-FI PROCESSOR
Gives the sound a "low-fidel-
ity" character.
20. NOISE GENERATOR
Generates noise.
21. RADIO TUNING
Reproduces the sound being
played on the radio.
22. SLICER + FLANGER
Continuously cuts the sound.
Includes a flanger effect.
23. RING MODULATOR
Creates a metallic sound quality.
24. CHROMATIC P.S.
Two-voice pitch shifter that
changes the pitch in semitone
steps.
25. VOICE TRANSFORMER
Processes human vocals to pro-
duce a variety of different
voices.
26. CENTER CANCELER
Eliminates the vocals and other
sounds located at the center.
CTRL 1
DRIVE
Adjusts the depth of distortion.
DRIVE
Adjusts the depth of distortion.
SENS
Adjusts the sensitivity of the
Wah effect.
-2OCT (-2 Octave Level)
Adds sound two octaves lower
than the original sound.
SUSTAIN
Adjusts the amount of the com-
pressor effect that is applied.
LOW
Adjusts the volume of the low
frequency range.
SMPL RTE (Sample Rate)
Adjusts the sampling frequency.
(*2)
COLOR
Adjusts the tone of the hissing
noise.
TUNING
Adjusts the degree of noise that
occurs when tuning a radio.
PTN (Timing Pattern)
Select a pattern to specify the
timing at which the sound will
be cut. (*3)
FREQ (Frequency)
Adjusts the pitch of the metallic
sound.
PITCH 1
Changes Pitch 1 up or down one
octave in semitone intervals.
FORMANT
Adjusts the vocal characteristics
(formant).
L-R BAL (L-R Balance)
Finds the best point for deletion.
Chapter 2. Using the internal effects
CTRL 2
TONE
Adjusts the tonal character.
TONE
Adjusts the tonal character.
FREQ (Frequency)
Adjusts the pitch of the effect
sound.
-1OCT (-1 Octave Level)
Adds sound one octave lower
than the original sound.
ATTACK
Adjusts the sound's attack.
MID (Middle)
Adjusts the volume of the
midrange.
BIT
Adjusts the bit count.
QUALITY
Sets how often the scratch noise
is produced.
NOISE LV (Noise Level)
Specifies the volume of the
noise.
RATE
Adjusts the length of the PTN
(Timing Pattern). (*4)
E.LEVEL (Effect Level)
Adjusts the volume of the effect
sound.
PITCH 2
Changes Pitch 2 up or down one
octave in semitone intervals.
E.LEVEL (Effect Level)
Adjusts the volume level of the
effect sound.
LO BOOST (Low Boost)
Boosts the bass and other low-fre-
quency sounds located at the cen-
ter.
CTRL 3
LEVEL
Specifies the volume.
LEVEL
Specifies the volume.
PEAK
Adjusts the wah's peak volume.
D.LEVEL (Direct Level)
Adjusts the volume level of the
direct sound.
LEVEL
Specifies the volume.
HIGH
Adjusts the volume of the high
frequency range.
FILTER
Adjust the sensitivity with
which the filter will be affected.
LEVEL
Adjust the volume level of the
hissing noise.
FERQ RNG (Frequency Range)
Adjusts the tonal character.
FLANGER
Adjusts the degree of the flanger
effect.
D.LEVEL (Direct Level)
Adjusts the volume level of the
direct sound.
BALANCE (Direct/Effect Balance)
Adjusts the balance of the effect
sound and direct sound.
D.LEVEL (Direct Level)
Adjusts the volume level of the
direct sound.
HI BOOST (High Boost)
Boosts the high-frequency
sounds.
37