Effects List - Boss SP-505 Owner's Manual

Chapter 2. Using the internal effects

Effects List

DSP EFFECTS
1. FILTER + DRIVE
Low-pass filter with overdrive.
Cuts the high frequencies and
adds distortion.
2. PITCH SHIFTER
Modifies the pitch.
3. DELAY
Repeats the sound.
4. VINYL SIMULATOR
Gives the sound the sonic quali-
ties of an analog record.
5. ISOLATOR
Extracts and deletes sounds in the
low-, mid-, or high-frequency range.
6. REVERB
Adds reverberation to the sound
7. TAPE ECHO
Vintage tape echo effect.
8. CHORUS
Adds spaciousness and depth to
the sound.
9. FLANGER
Adds a undulation like that of a
jet ascending or descending.
10. PHASER
Adds a kind of cyclic undulation
to the sound.
11. TREMOLO / PAN
Cyclically changes the volume
or pan.
12. DISTORTION
Strongly distorts the sound.
36
CTRL 1
CUTOFF
Adjusts the cutoff frequency.
PITCH
Changes the pitch up or down
two octaves.
DLY TIME (Delay Time)
Adjusts the time of the delayed
sound. (*1)
COMP (Compressor)
Adjusts the sense of compres-
sion in the sound that is charac-
teristic of analog records.
LOW
Extracts/deletes sounds in the
low-frequency range.
REV TIME (Reverb Time)
Adjusts the time of reverb.
REPEAT (Repeat Rate)
Sets the tape speed.
DEPTH
Sets the depth of the chorus.
DEPTH (Depth/Manual)
Adjusts the depth of the undula-
tion. When the CTRL 2 knob
(RATE) is turned fully counter-
clockwise, pitch (Manual) is
adjusted.
DEPTH (Depth/Manual)
Adjusts the depth of the undula-
tion. When the CTRL 2 knob
(RATE) is turned fully counter-
clockwise, pitch (Manual) is
adjusted.
DEPTH
Adjusts the amount of change in
the volume or pan.
DIST (Distortion)
Adjusts the depth of distortion.
CTRL 2
RESO (Resonance)
Adjusts the peak level at the cut-
off frequency.
FEEDBACK
Adjusts the feedback amount of
the pitch shift sound.
FEEDBACK
Adjust the number of times that
the delay will repeat.
NOISE LV (Noise Level)
Adjusts the volume of analog
record noise.
MID (Middle)
Extracts/deletes sounds in the
midrange.
TONE
Adjusts the quality of the reverb.
INTENS (Intensity)
Sets the amount of repetition of
the echo sound.
RATE
Specifies the rate of modulation.
RATE
Adjusts the rate of the undulation.
When turned fully counterclock-
wise, the undulation stops, and
the pitch (Manual) can be adjusted
with the CTRL 1 knob (DEPTH).
RATE
Adjusts the rate of the undulation.
When turned fully counterclock-
wise, the undulation stops, and
the pitch (Manual) can be adjusted
with the CTRL 1 knob (DEPTH).
RATE
Adjusts the rate of change in the
volume or pan.
TONE
Adjusts the tonal character.
CTRL 3
DRIVE
Adds distortion.
BALANCE
Adjusts the volume balance
between the effect sound and
the direct sound.
E.LEVEL (Effect Level)
Specifies the volume of the
delay.
WOW/F (Wow Flutter)
Adjusts the rotational irregulari-
ties that occur when playing an
analog record.
HIGH
Extracts/deletes sounds in the
high-frequency range.
E.LEVEL (Effect Level)
Adjusts the volume of the
reverb.
E.LEVEL (Effect Level)
Adjusts the volume of the echo
sound.
E.LEVEL (Effect Level)
Adjusts the volume of the effect
sound.
RESO (Resonance)
Adds a particular undulation to
the sound.
RESO (Resonance)
Adds a particular undulation to
the sound.
WAVE (Tremolo/Pan Waveform)
Changes the periodic curve of
the change in volume or pan.
When turned counterclockwise,
it is the volume that changes;
when turned clockwise, the pan
changes.
LEVEL
Specifies the volume.