Delay; Tape Echo; Reverse Delay; 3Tap Pan Delay - Roland V-Drums TD-27 Data List

DELAY

This is a stereo delay.
Parameter Value
Tempo Sync
OFF, ON
Left, Right
Delay Left,
1–1300msec, note
Right Time
Phase Left,
NORMAL, INVERSE Phase of the delay sound
Right
Feedback
NORMAL, CROSS
Mode
Feedback
-98–+98%
200–8000
HF Damp
Hz, BYPASS
Low Gain
-15–+15dB
High Gain
-15–+15dB
Level
0–127

TAPE ECHO

A virtual tape echo that produces a realistic tape delay sound. This
simulates the tape echo section of a Roland RE-201 Space Echo.
Parameter Value
S, M, L, S+M, S+L,
Mode
M+L, S+M+L
Repeat Rate
0–127
Intensity
0–127
Bass
-15–+15dB
Treble
-15–+15dB
Head S Pan
L64–R63
Head M Pan
L64–R63
Head L Pan
L64–R63
Tape
0–5
Distortion
W/F Rate
0–127
W/F Depth
0–127
Level
0–127
Explanation
Specifies whether the delay time value of the
left/right delay sounds is specified as a note
value (ON) or not (OFF).
Delay time from the original sound until the
left/right delay sound is heard
Selects the way in which delay sound is fed
back into the effect
NORMAL: The left/right delay sounds are fed
back without modification.
CROSS: The left/right delay sounds are
alternately exchanged when fed back.
Adjusts the amount of the delay sound that's
fed back into the effect.
Negative "-" settings will invert the phase.
Adjusts the frequency above which sound
fed back to the effect is filtered out. If you
don't want to filter out any high frequencies,
set this parameter to BYPASS.
Gain of the low frequency range
Gain of the high frequency range
Output Level
Explanation
Combination of playback heads to use Select
from three different heads with different
delay times
S: Short
M: Middle
L: Long
Tape speed
Increasing this value will shorten the spacing
of the delayed sounds.
Amount of delay repeats
Boost/cut for the lower range of the echo
sound
Boost/cut for the upper range of the echo
sound
Independent stereo location for the short,
middle, and long playback heads
Amount of tape-dependent distortion to be
added
This simulates the slight tonal changes
that can be detected by signal-analysis
equipment. Increasing this value will increase
the distortion.
Speed of wow/flutter (complex variation in
pitch caused by tape wear and rotational
irregularity)
Depth of wow/flutter
Output level

REVERSE DELAY

This is a reverse delay that adds a reversed and delayed sound to the
input sound. A tap delay is connected immediately after the reverse

delay.

Parameter Value
Threshold
0–127
Tempo Sync
OFF, ON
Rev
Rev Delay
1–1300msec, note
Time
Rev Delay
-98–+98%
Feedback
Rev Delay HF
200–8000Hz,
Damp
BYPASS
Rev Delay Pan
L64–R63
Rev Delay
0–127
Level
Tempo Sync
OFF, ON
Delay 1–3
Delay 1–3
1–1300msec, note
Time
Delay 3
-98–+98%
Feedback
Delay HF
200–8000Hz,
Damp BYPASS
Delay 1 Pan,
L64–R63
Delay 2 Pan
Delay 1 Level,
0–127
Delay 2 Level
Low Gain
-15–+15dB
High Gain
-15–+15dB
Level
0–127

3TAP PAN DELAY

Produces three delay sounds; center, left and right.
Parameter Value
Tempo Sync
Left, Right,
OFF, ON
Center
Delay Left,
Right, Center
1–2600msec, note
Time
Center
-98–+98%
Feedback
200–8000Hz,
HF Damp
BYPASS
Left, Right,
0–127
Center Level
Low Gain
-15–+15dB
High Gain
-15–+15dB
Level
0–127
Multi-Effect Parameters
Explanation
Volume at which the reverse delay will
begin to be applied
Specifies whether the delay time value of
the reverse delay is specified as a note value
(ON) or not (OFF).
Delay time from when sound is input into
the reverse delay until the delay sound is
heard
Proportion of the delay sound that is to be
returned to the input of the reverse delay.
(negative values invert the phase)
Frequency at which the high-frequency
content of the reverse-delayed sound will
be cut (BYPASS: no cut)
Stereo location of the reverse delay sound
Volume of the reverse delay sound
Specifies whether the delay time value of
the tap delay is specified as a note value
(ON) or not (OFF).
Delay time from when sound is input into
the tap delay until the delay sound is heard
Proportion of the delay sound that is to
be returned to the input of the tap delay
(negative values invert the phase)
Frequency at which the high frequency
content of the tap delay sound will be cut
(BYPASS: no cut)
Stereo location of the tap delay sounds
Volume of the tap delay sounds
Gain of the low frequency range
Gain of the high frequency range
Output Level
Explanation
Specifies whether the delay time value of the
left/right/center delay sound is specified as a
note value (ON) or not (OFF).
Adjusts the time until the delay sound is
heard.
Adjusts the amount of the delay sound that's
fed back into the effect. Negative "-" settings
invert the phase.
Adjusts the frequency above which sound
fed back to the effect is filtered out. If you do
not want to filter out any high frequencies,
set this parameter to BYPASS.
Volume of each delay
Gain of the low frequency range
Gain of the high frequency range
Output Level
43