Phaser A; Phaser B; Step Phaser; Flanger - Roland V-Drums TD-27 Data List

PHASER A

A phase-shifted sound is added to the original sound and modulated.
Parameter Value
4-STAGE, 8-STAGE,
Mode
12-STAGE
Manual
0–127
Tempo Sync
OFF, ON
0.05–10.00Hz,
Rate
note
Depth
0–127
INVERSE,
Polarity
SYNCHRO
Resonance
0–127
Cross
-98–+98%
Feedback
Low Gain
-15–+15dB
High Gain
-15–+15dB
Level
0–127

PHASER B

This simulates a different analog phaser than Phaser A.
Parameter Value
Speed
0–100
Depth
0–127
Low Gain
-15–+15dB
High Gain
-15–+15dB
Level
0–127
Explanation
Number of stages in the phaser
Adjusts the basic frequency from which the
sound will be modulated.
Specifies whether the modulation rate is
specified as a note value (ON) or not (OFF).
Frequency of modulation
Depth of modulation
Selects whether the left and right phase
of the modulation will be the same or the
opposite.
INVERSE: The left and right phase will be
opposite. When using a mono source, this
spreads the sound.
SYNCHRO: The left and right phase will be
the same. Select this when inputting a stereo
source.
Amount of feedback
Adjusts the proportion of the phaser sound
that is fed back into the effect. Negative "-"
settings will invert the phase.
Gain of the low range
Gain of the high range
Output Level
Explanation
Frequency of modulation
Depth of modulation
Gain of the low range
Gain of the high range
Output Level

STEP PHASER

The phaser effect will be varied gradually.
Parameter Value
4-STAGE, 8-STAGE,
Mode
12-STAGE
Manual
0–127
Tempo Sync
OFF, ON
(Rate)
0.05–10.00Hz,
Rate
note
Depth
0–127
INVERSE,
Polarity
SYNCHRO
Resonance
0–127
Cross
-98–+98%
Feedback
Tempo Sync
OFF, ON
(Step Rate)
0.10–20.00Hz,
Step Rate
note
Low Gain
-15–+15dB
High Gain
-15–+15dB
Level
0–127

FLANGER

This is a stereo flanger. (The LFO has the same phase for left and
right.) It produces a metallic resonance that rises and falls like a jet
airplane taking off or landing. A filter is provided so that you can
adjust the timbre of the flanged sound.
Parameter Value
Filter Type
OFF, LPF, HPF
Cutoff Freq
200–8000Hz
Pre Delay
0.0–100.0ms
Tempo Sync
OFF, ON
0.05–10.00Hz,
Rate
note
Depth
0–127
Phase
0–180deg
Feedback
-98–+98%
Low Gain
-15–+15dB
High Gain
-15–+15dB
Level
0–127
Multi-Effect Parameters
Explanation
Number of stages in the phaser
Adjusts the basic frequency from which the
sound will be modulated.
Specifies whether the modulation rate is
specified as a note value (ON) or not (OFF).
Frequency of modulation
Depth of modulation
Selects whether the left and right phase
of the modulation will be the same or the
opposite.
INVERSE: The left and right phase will be
opposite. When using a mono source, this
spreads the sound.
SYNCHRO: The left and right phase will be
the same. Select this when inputting a stereo
source.
Amount of feedback
Adjusts the proportion of the phaser sound
that is fed back into the effect. Negative "-"
settings will invert the phase.
Specifies whether the modulation rate of the
phaser effect is specified as a note value (ON)
or not (OFF).
Rate of the step-wise change in the phaser
effect
Gain of the low range
Gain of the high range
Output Level
Explanation
Type of filter
OFF: no filter is used
LPF: cuts the frequency range above the
Cutoff Freq
HPF: cuts the frequency range below the
Cutoff Freq
Specifies the frequency at which the filter
cuts a specific frequency region
Adjusts the delay time from when the direct
sound begins until the flanger sound is
heard.
Specifies whether the modulation rate is
specified as a note value (ON) or not (OFF).
Frequency of modulation
Depth of modulation
Spatial spread of the sound
Adjusts the proportion of the flanger sound
that is fed back into the effect. Negative "-"
settings will invert the phase.
Gain of the low range
Gain of the high range
Output Level
45