Fujitsu Airstage UTY-RNRYZ3 Installation Manual page 8

3.
The "Maintenance" screen is displayed. Touch [Next Page] or
[Previous Page] to switch between screens.
(Items that indoor unit does not support are not displayed.)
Maintenance
Page 1/ 3 Maintenance
Setting
Error History Test Run
Status List
Filter Sign I.U. Address
Version
Reset Verification
Next
Back Back
Page
6.4.1. Error History
1.
Touch the [Error History] on the "Maintenance" screen. The "Error
History" screen is displayed.
If there are 7 or more errors, you can switch between pages by
touching [Next Page] or [Previous Page] Up to a maximum of 32 er-
rors can be saved. Once there are more than 32 errors, the oldest
one will be deleted.
Touch [Back] to return to the "Maintenance" screen.
2.
To delete the error history, touch [Erase All] and then [Yes] on the
confi rmation screen.
1. 2.
Error History
Page 1/ 2 Error History
No. Date Time Address Code
1 2015/ 8/ 1 11:00 AM 002-01 141
2 2015/ 7/30 2:53 AM 002-02 143
3 2015/ 7/25 8:53 AM 002-02 143
4 2015/ 7/22 11:00 AM 002-01 141
5 2015/ 7/22 11:00 AM 002-01 141
6 2015/ 7/21 11:00 AM 002-01 141
Next Erase
Back
Page All
6.4.2. Setting Status List
1.
Touch the [Setting Status List] on the
"Maintenance" screen. The "Setting Status
List" screen is displayed.
Touch [Next Page] or [Previous Page] to
switch between screens.
Touch [Back] to return to the "Maintenance"
screen.
6.4.3. Filter Sign Reset
1.
Touch the [Filter Sign Reset] on the
"Maintenance" screen. The "Filter Sign
Reset" screen is displayed.
Touch [OK] to reset the fi lter sign, and
return to the "Maintenance" screen.
6.4.4. Version
1.
Touch the [Version] on the "Maintenance"
screen. The "Version" screen is displayed.
Touch [Back] to return to the "Maintenance"
screen.
6.4.5. Test Run
Carry out a test run after completing confi guration.
1.
Touch the [Test Run] on the "Maintenance"
screen. The "Test Run" screen is
displayed.
Touch [OK] to return to the "Maintenance"
screen, and start the test run. The test run
will automatically end in approximately 60
min.
If you wish to cancel the test run before it is complete, return to the
"Monitor Mode screen", and touch the On/Off button.
En-8
Maintenance
Page 2/ 3
R.C. Address Installer Password
Setting Change
Function Setting
Previous Next Previous
Back
Page Page Page
Delete entire error history?
No Yes
Setting Status List
On Timer
– Operation Start Time
Off Timer
– Operation Stop Time
Auto Off Timer
– Operation Stop Time
– Time Range
Back
Filter Sign Reset
The filter sign will be reset. OK?
Cancel
Version
E000V00P00L00
Back
Test Run
The test run will be performed. OK?
Cancel
6.4.6. R.C. Address Setting
Addresses will be automatically set when initially starting up this unit. In
such a case, do not change the remote controller address for the indoor
unit, and keep it at the initial setting of 0.
Page 3/ 3
Initialization
• Checking the remote controller address
1.
Touch the [R.C. Address Setting] on the
"Maintenance" screen. The "R.C. Address
Setting" screen is displayed.
The "Current Address" is displayed as
[System-Unit]. The value for "Unit" refers
to the remote controller address.
Touch [Back] to return to the "Maintenance" screen.
When the address is set manually, this mark
is displayed.
• Manual Address Setting
Only set addresses manually when using different numbers for
addresses.
A remote-controller address for the indoor unit needs to be set.
Set the remote-control addresses for the indoor units which are
connected using the same remote-control cable with a range from 1 to
9 and from A (10) to F(15), without any duplicates. (Do not use "0" for
confi guration.)
For how to confi gure the remote control addresses for the indoor unit,
refer to its installation manual.
1.
Page 1/ 5
Touch the [RC Address Setting] on the "Maintenance" screen. The
[Disable]
[0.5hr] "R.C. Address Setting" screen is displayed.
[Disable]
[0.5hr]
Touch the [Manual Addressing]. The "Manual Addressing" screen is
[Disable]
[30min.]
displayed.
[ – ]
Next
2.
Page
Touch [ ] or [ ] to set the addresses of this unit. Touch [OK] to
display the confi rmation screen, and touch [Yes] to return to the RC
Address setting screen.
If you wish to carry out confi guration again, touch [Address Reset] on
the "R.C. Address Setting".
1.
R.C.Address Setting
Current Address
Manual Addressing
OK
Address Reset
Back
The address for this unit can be set from 1 to 32. However, do not set
the same number as that for the remote-control address of an indoor
unit connected using the same remote-control cable.
6.4.7. I.U. Address Verifi cation
Check the address and position of the indoor unit.
1.
Touch the [I.U. Address Verifi cation] on the "Maintenance" screen.
The "I.U. Address Verifi cation" screen is displayed.
If there are multiple pages, you can switch between them by
touching [Next Page] or [Previous Page].
Touch [Check] to display the indoor unit address checking start
screen.
2.
Touch [Yes] to display the confi rmation screen.
3.
Select the indoor unit to be checked. If there are multiple pages,
OK
you can switch between them by touching [Next Page] or [Previous
Page]. The selected indoor unit will start to blow air and fl ash a
LED*. (*Only when the indoor unit has the relevant functions)
Touch [Back] on the confi rmation screen to return to the previous
screen.
1.
I.U. Address Verification
No. System–Unit /
1 002–01 /
2 002–02 /
3 002–03 /
4 002–04 /
5 002–05 /
6 002–06 /
Back
4.
Touch [Back] on the "IU Address
Verifi cation" Screen to return to the
"Maintenance" Screen.
2.
Manual Addressing
System Unit
[001–01]
001 01
Cancel OK
2.
Page 1/ 2 I.U. Address Verification
Ref.–In.
01–01
01–02
01–03
Indoor unit position will be checked. OK?
01–04
01–05
01–06
Next
Check
No Yes
Page
R.C.Address Setting
Current Address [001–01]
Manual Addressing
Address Reset
Back
3.
I.U. Address Verification Page 1/ 2
No. System–Unit / Ref.–In.
1 002–01 / 01–01
2 002–02 / 01–02
3 002–03 / 01–03
Next
End
Page
I.U. Address Verification
Page 1/ 2
No. System–Unit / Ref.–In.
1 002–01 / 01–01
2 002–02 / 01–02
3 002–03 / 01–03
4 002–04 / 01–04
5 002–05 / 01–05
6 002–06 / 01–06
Next
Back Check
Page