Table of Contents
Advertisement
ENGLISH
SPECIFICATIONS
Motor.......................................................
Speed (no load).......................................
Double insulated.....................................
Saw blade................................................
Arbor size.................................................
Dust port size...........................................
Bevel range..............................................
Miter range..............................................
Cutting capacity:
Cross cut 0° x 0°.......................................
Miter cut 45° x 0°....................................
Bevel cut 0° x 45°....................................
Compound cut 45° x 45°.........................
Crown capacity:
Crown molding nested...........................
Baseboard against fence.........................
Miter/bevel positive stop angles:
Miter detent stops...................................
Bevel positive stops.................................
Weight.....................................................
LOOSE PARTS
The following items are included with your miter saw:
Fig. 4
A
A. Miter saw assemby.......................................................................................
B. Workpiece clamp..........................................................................................
C. Dust bag.........................................................................................................
D. Wrench (in wrench storage)........................................................................
ASSEMBLY
Unpacking your miter saw
This product requires assembly.
•
Carefully lift saw from the carton by the carrying handle
located at the top of the saw body, and place it on a
level work surface.
CAUTION: This tool is heavy. To avoid back injury,
lift with your legs, not your back, and get help
when needed.
•
This saw has been shipped with the miter table 60° right
& saw head 0° and the saw head secured in the down
position.
•
To release the saw head, push down the switch handle
and pull out the head lock pin.
8
120 V~ 60 Hz, 15 A
4500 RPM
Yes
10" (254 mm) 40T Carbide-tipped
5/8" (15.9 mm)
1 1/2" (38.1 mm)
0-48° (left)
0-52° (left) & 0-60° (right)
1 1/2" x 12" (38.1 x 304.8 mm) /
3 1/2" x 3 1/2" (88.9 x 88.9 mm)
1 1/2" x 7 1/4" (38.1 x 184.2 mm)
1 1/2" x 12" (38.1 x 304.8 mm)
1 1/2" x 7 1/4" (38.1 x 184.2 mm)
5 1/4" (133 mm)
3 5/8" (92 mm)
0°, 15°, 22.5°, 31.6°, 45° (left)
0°, 15°, 22.5°, 31.6°, 45°, 60° (right)
0°, 22.5°, 33.6°, 45°
40.4 lb (18.36 kg)
B
C
D
•
Raise the saw head by the handle. Hand pressure should
remain on the switch handle to prevent sudden rise
upon release of the head lock pin.
•
Inspect the tool carefully to make sure that no breakage
or damage occurred during shipping.
•
Do not discard the packing material until you have
carefully inspected and satisfactorily operated the tool.
•
The saw is factory set for accurate cutting. After
assembling it, check for accuracy. If shipping has
in uenced the settings, refer to speci c procedures
explained in this Operator's Manual.
•
If any part is missing or damaged, do not attempt to
assemble the miter saw, plug in the power cord, or turn
the switch ON until the missing or damaged part is
obtained and is installed correctly.
WARNING: The use of attachments or accessories not
listed in this manual might be hazardous and could
cause serious personal injury.
WARNING: Do not attempt to modify this tool or
create accessories not recommended for use with
this tool. Any such alteration or modi cation is
misuse, and could result in a hazardous condition
leading to possible serious personal injury.
WARNING: Do not connect to the power supply
until assembly is complete. Failure to comply could
result in accidental starting and possible serious
personal injury.
WARNING: Do not start the miter saw without
checking for interference between the saw blade and
the sliding fences. Damage could result to the blade if
it strikes the sliding fence during operation of the saw.
WARNING: This saw can tip over if the saw head is
1
released suddenly and the saw is not secured to a
1
work surface. Always make sure the miter saw is
1
securely mounted to a workbench or approved
1
workstand. Failure to heed this warning can result in
serious personal injury.
WARNING: Many of the illustrations in this manual
show only portions of the miter saw. This is intentional
so that we can clearly show points being made in the
illustrations. Never operate the saw without all guards
securely in place and in good operating condition.
You will need
Items not supplied:
Framing square
5 mm Hex key
Items supplied:
Wrench (1 pc)
Hide quick links:
Advertisement
Table of Contents
