Advertisement
Quick Links
Advertisement
Related Manuals for Wolf Sub-Zero BI Series
Summary of Contents for Wolf Sub-Zero BI Series
- Page 1 subzero.com 800.222.7820 Service Manual BI-36F...
- Page 2 Built-In (BI) Series Component Removal Built-In (BI) Series (SWS #4380000) (SWS #4380000) Model BI-36F Exterior Cosmetic / Mechanical Components Kickplate To remove a kickplate, extract the screws from the left and right corners of the kickplate, then pull the kickplate forward. (See Figure 6-76). Screw Dual Installation Kickplate A dual installation kickplate assembly is held in place...
- Page 3 Built-In (BI) Series Component Removal Built-In (BI) Series (SWS #4380000) (SWS #4380000) Water Valve Assembly AC Connection NOTE: Before attempting to remove an isolation &/or water valve assembly, switch the water supply to the unit off. DC Connection To remove a valve assembly (See Figure 6-79): 1.
- Page 4 Built-In (BI) Series Component Removal Built-In (BI) Series (SWS #4380000) (SWS #4380000) Water Filter Manifold/Valve The water filter and manifold are located at the right- Manifold/Valve Electrical hand top side of the unit behind grille assembly. Connection NOTE: Before attempting to remove the water filter manifold, switch the water supply to the unit off.
- Page 5 Built-In (BI) Series Component Removal Built-In (BI) Series (SWS #4380000) (SWS #4380000) Framed / Overlay Door Handle / Handle-Side Trim The door handle on framed units and the handle-side trim on overlay units is attached to the door with screws. These screws are covered by a screw cover. To remove a handle of handle-side trim, open the door then: 1.
- Page 6 Built-In (BI) Series Component Removal Built-In (BI) Series (SWS #4380000) (SWS #4380000) Top Door Hinge Assembly The top hinge assembly is secured to the unit with bolts that pass down through the cabinet hinge plate into threaded inserts. Screws passing down through the door hinge secure the hinge assembly to the door.
- Page 7 Built-In (BI) Series Component Removal Built-In (BI) Series (SWS #4380000) (SWS #4380000) Door Assembly The door assembly is secured to the top and bottom door hinges with screws. The post of the bottom door Bottom Cabinet Hinge Assembly hinge fits down into a bearing in the bottom cabinet hinge assembly’s door adjuster.
- Page 8 Built-In (BI) Series Component Removal Built-In (BI) Series (SWS #4380000) (SWS #4380000) Model BI-36F Interior Cosmetic / Mechanical Components Door Gasket A dart at the back of the door gasket fits into metal Metal Channels channels attached to the inside perimeter of the door. To remove a door gasket, starting at one corner, pull the gasket dart from the metal channels.
- Page 9 Built-In (BI) Series Component Removal Built-In (BI) Series (SWS #4380000) (SWS #4380000) Fixed Glass Shelf Assembly The freezer fixed glass shelf rests upon shelf standoffs that are mounted to the freezer side walls. To remove the freezer fixed glass shelf (See Figure 6- 96): 1.
- Page 10 Built-In (BI) Series Component Removal Built-In (BI) Series (SWS #4380000) (SWS #4380000) Icemaker Assembly Icemaker Assembly The icemaker assembly is attached to the left side of the middle duct assembly with screws. To remove ice maker, first remove the fixed glass shelf assembly and the upper freezer basket assembly, then (See Figure 6-99): 1.
- Page 11 Built-In (BI) Series Component Removal Built-In (BI) Series (SWS #4380000) (SWS #4380000) Upper LED Light Bulb and Light Bracket Assembly The lighting assemblies are located behind the light dif- fuser at the top of the compartment. Ground Clip To remove LED light bulbs, first remove the light dif- fuser, then turn the bulb counterclockwise to remove it.
- Page 12 Built-In (BI) Series Component Removal Built-In (BI) Series (SWS #4380000) (SWS #4380000) Middle Duct Assembly Middle Duct The middle duct assembly is secured to the compart- Assembly ment back wall, lower duct assembly and evaporator fan assembly with screws. To remove the middle duct assembly, first remove all cantilever shelves, the fixed glass shelf, upper freezer basket assembly, icemaker assembly, upper light dif- fuser, light diffuser brackets and upper duct assembly,...
- Page 13 Built-In (BI) Series Component Removal Built-In (BI) Series (SWS #4380000) (SWS #4380000) Lower LED Light Tube LED Light Tube The LED light tube is held by plastic light clips that are inserted into the lower duct. The light tube wire leads Grommet Slot in are inserted back through a plastic grommet in the Lower...
- Page 14 Built-In (BI) Series Component Removal Built-In (BI) Series (SWS #4380000) (SWS #4380000) Freezer Defrost Terminator Defrost The freezer defrost terminator is attached to a return Terminator elbow of the evaporator. To remove the defrost terminator, first remove all can- tilever shelves, the fixed glass shelf, all freezer baskets, icemaker assembly, upper light diffuser, light diffuser brackets, upper duct assembly, middle duct assembly and lower duct assembly, then (See Figure 6-111):...
- Page 15 Built-In (BI) Series Component Removal Built-In (BI) Series (SWS #4380000) (SWS #4380000) Model BI-36F Compressor Area Mechanical Components NOTE: For water filter and filter manifold, see Exterior Cosmetic / Mechanical Components earlier in this section. Main Control Board Screws hold the main control board inside a control housing that sits on a slide support bracket at the left side of the compressor area.
- Page 16 Built-In (BI) Series Component Removal Built-In (BI) Series (SWS #4380000) (SWS #4380000) Condenser Fan Motor Brackets The condenser fan is mounted to the condenser fan shroud with three fan mounting brackets that hook into grommets that are in the condenser fan shroud. At the back of the motor, screws pass through these brackets into the back of the fan motor.
- Page 17 Built-In (BI) Series Component Removal Built-In (BI) Series (SWS #4380000) (SWS #4380000) Model BI-36F Sealed system Components The sealed system components at the top of the appliance sit on a sliding unit tray. There is a slot in the unit tray running from front to back, with a bolt positioned in the middle of this slot and attached to the top of the appliance. This allows the tray to be pulled straight forward to aid in sealed system repairs.
- Page 18 Built-In (BI) Series Component Removal Built-In (BI) Series (SWS #4380000) (SWS #4380000) Compressor Compressor Electrical Compressors are secured to the unit tray with three Assembly, shoulder screws that pass down through rubber grom- Capacitor & Clip Compressor mets in the compressor base and into holes in unit tray. A metal tab formed into the unit tray passes up through the fourth rubber grommet and the compressor base.
- Page 19 Built-In (BI) Series Component Removal Built-In (BI) Series (SWS #4380000) (SWS #4380000) Freezer Evaporator The freezer evaporator is attached to the rear wall of the compartment with screws, behind the compartment duct assemblies. See Duct Assembly removal proce- dures earlier in this section. NOTES: The high-side filter-drier must also be replaced when replacing an evaporator.
- Page 20 Built-In (BI) Series Component Removal Built-In (BI) Series (SWS #4380000) (SWS #4380000) Heat Exchanger The freezer heat exchanger passes through the ceiling of the compartment. Cut Here NOTES: The high-side filter-drier must also be replaced when • replacing a heat exchanger. To remove a heat exchanger, first capture the refriger- ant from the sealed system, then (See Figure 6-124): 1.