Table of Contents
Advertisement
/""'\I--Ground
~~9901973
1389000
1004600 2 Speed (Square part)
1007600 Super, Jr. & Jeans Machine
1004800 2 Speed (Square part)
3003400
~1093200
9900089
1025000
Installation - Twist-Lock Type Electrical Connector
1105100 (110/1 Phase)
1105300 (220/1 Phase)
1105500 (3 Phase)
9900098 (1 Phase)
9900099 (3 Phase)
1105001 (110/1 Phase)
1105201 (220/1 Phase)
1105401 (3 Phase)
9900142
1048100
(1 Phase & 3 Phase)
11---1134060 (Ground)
(See notes #3 & #4)
Part No.
1004600
1004800
1005260
1007000
1007250
1007450
1007550
1007600
1014000
1015000
1024000
1025000
1025200
1048100
1058093
1093200
1101950
1102100
1007250 Super, Jr. & Jeans Machine
MOTOR AND CORD CONNECTOR NUMBERS - IN NUMERICAL ORDER
Description
Quantity used
if
more than 1
Inner Breaker - 2 Speed - 1 Phase (Square part)
Insulator - 2 Speed - 1 Phase (Square part)
Outer Breaker - 2 Speed - 1 Phase
3 Phase Spacer
Inner Breaker - Super, Jr.
&
Jeans Machine -1 Phase
Outer Breaker 60 Cycle - Single Speed - 1 Phase
Outer Breaker 50 Cycle - Single Speed - 1 Phase
Insulator - Super, Jr.
&
Jeans Machine - 1 Phase
Fan
Fan Locknut
Rear Head
Rear Cover
Knob Cover
Twist-Lock Connector Base - 1 Phase
&
3 Phase
Rear Head Bearing
Bearing Spacer
1 Phase Connection
1 Phase Brass Insert
1. Discount electrical connector.
2. Remove old type connection box. Pull out
terminal block by removing the 3 screws
on the outside of connection box.
Disconnect wires on the back of the block.
3. If the new male plug is mounted on the
Twist-Lock base, remove it. Bring lead
wires through new base being installed.
Before base is secured to motor case, the
Green Ground wire #1134060 must be
properly attached. Note: Place ground
between base and motor case, attaching
it with anyone of the screws, leading the
other end up through the base.
4. Connect leads and ground wires to male
plug. Make certain ground wire is con
nected to right angle shaped terminal pin.
Note: Be sure three phase machines
rotate in same direction as arrow stamped
on the rear motor case. To check, make a
flash contact with switch turned on. If
rotation is incorrect, reverse by changing
the lead wires on the male plug. Motor
must rotate in proper direction or serve
damage will result.
Part No.
Description
Quantity used
if
more than 1
1105001
1105100
1105201
1105300
1105401
1105500
1134060
1382183
1386700
3003400
9900089
9900098
9900099
9900119
9900123
9900142
9901973
110/1 Phase Twist-Lock Male Plug
110/1 Phase Twist-Lock Male Plug
220/1 Phase Twist-Lock Female Plug
220/1 Phase Twist-Lock Female Plug
3 Phase Hubbell Male Plug
3 Phase Hubbell Female Plug
Ground Wire
Rotor Knob SA
Spacer
Acorn Nut (8 on Dual
&
Jeans Machine)
Knob Cover Screw
Screw for 1 Phase Plug
Screw for 3 Phase Plug
Screw for Breaker
Screw for Rear Cover
Screw for Hubbell Base
Washer
4
2
3
2
2
4
3
3
Cord Connector
1102100
1101950
(1 Phase)
I
1007550 Single Speed 50 Cycle
1007450 Single Speed 60 Cycle
1005260 Two Speed
)
19
Advertisement
Table of Contents
