Mechanism Section Adjustment; How To Enter Record Mode Without; Cassette; How To Enter Playback Mode Without - Sony DCR-HC65 Adjusting Manual

6-2. MECHANISM SECTION ADJUSTMENT

On the mechanism section adjustment
For detail of mechanism section adjustments, checks, and
replacement of mechanism parts, refer to the separate volume "DV
MECHANICAL ADJUSTMENT MANUAL
Note: Before performing the adjustments, check the data of page: 0,
address: 10 is "00". If not, set data: 00 to this address.
2-1.

HOW TO ENTER RECORD MODE WITHOUT

CASSETTE

1) Connect the adjustment remote commander to the LANC jack.
2) Turn the HOLD switch of the adjustment remote commander
to the ON position.
3) Close the cassette compartment without the cassette.
4) Select page: 3, address: 01, and set data: 0C, and press the
PAUSE button of the adjustment remote commander.
(The mechanism enters the record mode automatically.)
Note: The function buttons becomes inoperable.
5) To quit the record mode, select page: 3, address: 01, set data:
00, and press the PAUSE button of the adjustment remote
commander. (Whenever you want to quit the record mode, be
sure to quit following this procedure.)
2-2.

HOW TO ENTER PLAYBACK MODE WITHOUT

CASSETTE
1) Connect the adjustment remote commander to the LANC jack.
2) Turn the HOLD switch of the adjustment remote commander
to the ON position.
3) Close the cassette compartment without the cassette.
4) Select page: 3, address: 01, and set data: 0B, and press the
PAUSE button of the adjustment remote commander.
(The mechanism enters the playback mode automatically.)
Note: The function buttons becomes inoperable.
5) To quit the playback mode, select page: 3, address: 01, set data:
00, and press the PAUSE button of the adjustment remote
commander. (Whenever you want to quit the playback mode,
be sure to quit following this procedure.)
2-3.

1. Preparation for Adjustment

1) Clean the tape running side (tape guide, drum, capstan shaft,
pinch roller, etc.).
2) Connect the adjustment remote commander to the LANC jack.
Z Mechanism ".
3) Turn the HOLD switch of the adjustment remote commander
to the ON position.
4) Connect an oscilloscope to VC-359 board CN1207 via the CPC
connecting jigs. (J-6082-521-A, J-6082-564-A)
Channel 1: VC-359 board, CN1207 Pin 1 (Note)
External trigger: VC-359 board, CN1207 Pin 2
Note: Connect a 75Ω resistor between Pins 1 of CN1207 and 3
5) Playback the alignment tape for tracking. (XH2-1)
6) Select page: 3, address: 33, and set data: 08.
7) Select page: 3, address: 26, set data: 31, and press PAUSE
button.
8) Check that the oscilloscope RF waveform is normal at the
entrance and exit.
If not normal, adjust according to the separate volume "DV
MECHANICAL ADJUSTMENT MANUAL
CN1207 of VC-359 board

2. Processing after Completing Operations:

1) Connect the adjustment remote commander to the LANC jack
and set the HOLD switch to the ON position.
2) Select page: 3, address: 26, and set data: 00, and press PAUSE
button.
3) Select page: 3, address: 33, and set data: 00.
Entrance
side
CH1
CH2
(Trigger)
6-39

TAPE PATH ADJUSTMENT

(GND).
Pin No. Signal Name
1 RF MON
2 SWP
3 GND
4 XCS EEP
5 EEP SCK
6 EEP SO
7 EEP SI
8 GND
Table 6-2-1.
Check this section
(Normal waveform)
3.3 msec
Fig. 6-2-1.
DCR-HC65
Z Mechanism ".
Exit side