Advertisement
Quick Links
KIT COMPONENTS
• A) Radio bezel • B) Bezel mount • C) Radio brackets • D) Pocket • E) Phillips screws (4) • F) Panel clips (4)
A
B
Metra. The World's Best Kits.
®
Mini Cooper Hardtop
Mini Cooper Hardtop
MetraOnline.com
Visit
for more detailed information about the product and up-to-date vehicle
specific applications
KIT FEATURES
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Retains the factory hazard button
† Base model radio without a high-def display
C
MetraOnline.com
2014-2017
coupe 3-dr (F56)
2014-2017
sedan 5-dr (F55)
• Painted high gloss black with
a matte black trim to match the
factory appearance
D
E
F
© COPYRIGHT 2020 METRA ELECTRONICS CORPORATION
99-9326B
I N S TA L L AT I O N I N S T R U C T I O N S
†
TABLE OF CONTENTS
Dash Disassembly ..................................................2
†
Kit Preparation .......................................................3
Kit Assembly
–ISO DIN radio provision with pocket ..................4
–ISO DDIN radio provision .....................................5
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • See metraonline for harness
interface solutions
Antenna Adapter: 40-EU55 (sold separately)
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Heavy duty pick tool (or flat-blade screwdriver)
• T-20 Torx screwdriver
Attention!
Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
REV. 4/7/20 INST99-9326B
Advertisement
Related Manuals for Metra Electronics 99-9326B
Summary of Contents for Metra Electronics 99-9326B
- Page 1 When testing the aftermarket equipment, ensure that all factory equipment is connected before cycling the key to ignition. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 4/7/20 INST99-9326B...
- Page 2 DASH DISASSEMBLY 1. Remove (2) expanding rivets securing 4. Locate the access hole under the speaker the bottom of the radio bezel, then grille. Using a heavy duty pick tool or unclip and remove the bezel. (Figure A) flat-blade screwdriver, push down on the locking clip holding the top of the 2.
- Page 3 KIT PREPARATION From the factory radio panel: 1. Remove (2) metal retainer clips. Attach the clips onto the bezel mount. (Figure A) 2. Unclip and remove the hazard switch (Figure A) To the radio bezel provided with the kit: 3. Attach (4) panel clips provided. (Figure B) Continue to Kit Assembly (Figure A)
- Page 4 KIT ASSEMBLY ISO DIN radio provision with pocket 3. Secure the pocket to the radio brackets using (4) Phillips screws provided. 1. Remove (2) T-20 Torx screws securing (Figure C) the a/c vents. (Figure A) 4. Remove the metal DIN sleeve and trim 2.
- Page 5 KIT ASSEMBLY (CONT.) 6. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or Axxess. Test the radio for proper operation. 7.
- Page 6 KIT ASSEMBLY ISO DDIN radio provision 1. Remove (2) T-20 Torx screws securing the a/c vents. (Figure A) 2. Route the hazard switch wiring harness through the bezel mount, then clip the mount to the dash. (Figure B) 3. Secure the radio brackets to the radio using screws supplied with the radio.
- Page 7 KIT ASSEMBLY (CONT.) 5. Slide the radio into the dash, then secure using (2) a/c vent screws up top, and (2) Torx T-20 screws removed in Dash Disassembly down below. (Figure D) 6. Route the hazard switch wiring harness through the radio bezel, then clip the bezel to the dash.
- Page 8 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 4/7/20 INST99-9326B...