Commands And Control Instruments; Seat Assembly (5) (Mod. 340 Ix); Bellows Installation (7) (Mod. 740 Iox, 540 Ix); Install The Carrier (8) - Stiga Park 4WD Series Instruction Manual

EN
5 2 3 Seat assembly (5) (Mod 340 IX)
1 The seat is supplied already assembled on
the support plate.
2. Position the seat by aligning the holes in the
seat plate with those on the bottom plate.
3. Insert the screws (M8x40) in the holes on
the seat bracket and in the holes on the seat
plate.
4. Screw the seat into place. Tightening torques
20±25 Nm.
If the screws are tightened more than
25 Nm, the seat will be damaged
5 2 4 Bellows installation (7) (Mod 740 IOX,
540 IX)
1. Fasten the seat in place with the two screws
(7:B).
2. Position the bellows (7:A).
3. Secure the bellows in place with the 10 pegs
(7:C).

5 2 5 Install the carrier (8)

Install the carrier (8:B) on the back of the seat
(8:A) using the 4 screws (8:C).
5 3

STEERING WHEEL (9)

1. Push the steering wheel sleeve (9:A) all the
way down the steering column (9:B) .
2. Align the holes on the sleeve with those on
the steering column.
3. Once the holes have been aligned (9:C), in-
sert the two pins (9;D).
5 4

TOW BAR (10)

Install the tow bar (10:A) on the rear of the machi-
ne.
Use the screws and nuts (10:B; 10:C).
Tightening torque: 22 Nm.
5 5

QUICK-RELEASE SUPPORTS (1:P)

The quick-release supports and relative installa-
tion instructions are supplied in a separate box
inside the machine packaging.
Install the quick-release supports on the machi-
ne's front axles.
5 6

BATTERY CHARGING

The battery must be fully charged befo-
re being used for the first time.
Please refer to 9 9 for the battery char-
ging procedure
12
ENGLISH
5 7

TYRE PRESSURE

For the tyre pressure, please refer to "0 TECHNI-
CAL DATA TABLE"
5 8

ACCESSORIES

For installation of accessories, see the installation
guide accompanying each accessory.
For the application of the correct at-
tachments, please contact the authori-
sed service centre
Note: In this case the cutting means as-
sembly is considered an accessory
6 COMMANDS AND CONTROL
6 1

BONNET (11)

The bonnet can be opened as follows:
1. Turn the two screws through 90° (11:A)
2. Pull the handle up (11:B) while at the same
time carefully lifting the bonnet (11:C).
3. To close the bonnet, gently push down on it,
if necessary, until the handle engages (11:B).
Turn the two screws through 90° (11:A).
It is prohibited to start the engine when
the bonnet is open
6 2

MAIN POWER KEY SWITCH (12)

The electrical power supply is activated by a key
(12:A). This can be found under the bonnet (1:H)
consequently to get to the main power switch you
must first open the bonnet (see 6.1).
Insert the key (12:A) in the main power switch,
push in and turn clockwise to switch on the electri-
cal system's power supply.
Turn the key counter-clockwise to turn the power
supply off.
The key can only be removed from
the switch when it is turned counter-
clockwise
6 3

PARKING BRAKE PEDAL (13:A)

Never partially press the pedal while
driving There is a risk of overheating
the power transmission
The pedal (13:A) has the following three positions:
(Translation of the Original Instructions)
INSTRUMENTS