DURKOPP ADLER M-TYPE DELTA D867 Additional Instructions
  1. Manuals
  2. Brands
  3. DURKOPP ADLER Manuals
  4. Sewing Machine
  5. M-Type Delta D867
  6. Additional instructions
DURKOPP ADLER M-TYPE DELTA D867 Additional Instructions

DURKOPP ADLER M-TYPE DELTA D867 Additional Instructions

Electropneumatic needle cooling
Hide thumbs Also See for M-TYPE DELTA D867:
Table of Contents

Advertisement

Quick Links

Download this manual
D867
M-TYPE DELTA
Additional Instructions
Electropneumatic needle cooling

Advertisement

Table of Contents
loading

Related Manuals for DURKOPP ADLER M-TYPE DELTA D867

Summary of Contents for DURKOPP ADLER M-TYPE DELTA D867

  • Page 1 D867 M-TYPE DELTA Additional Instructions Electropneumatic needle cooling...
  • Page 2 IMPORTANT READ CAREFULLY BEFORE USE KEEP FOR FUTURE REFERENCE All rights reserved. Property of Dürkopp Adler AG and protected by copyright. Any reuse of these contents, including extracts, is prohibited without the prior written approval of Dürkopp Adler AG. Copyright © Dürkopp Adler AG 2020...

  • Page 3: Table Of Contents

    Table of Contents General information ..............3 Components of the kit 0867 594464 (needle cooling from above) ............3 Components of the kit 0867 594474 (needle cooling from below, thread trimmer) ........ 4 Components of the kit 0867 594484 (needle cooling from below, short thread trimmer) ....... 4 Needle cooling from above............
  • Page 4 Table of Contents Additional Instructions D867 - 01.0 - 04/2020...

  • Page 5: General Information

    General information General information Important The machine is not equipped with compressed air. If you want to assemble the electropneumatic needle cooling to the machine, you will need the following additional kits (see  Parts List): • 9780 000108: Compressed air maintenance unit •...

  • Page 6: Components Of The Kit 0867 594474 (Needle Cooling From Below, Thread Trimmer)

    General information 1.2 Components of the kit 0867 594474 (needle cooling from below, thread trimmer) Check whether the scope of delivery for kit 0867 594474 is correct prior to installation. Part number Quantity Designation 0867 214250 Feed dog 9790 315002 Hose connector 0999 240394 T-R coupling screw...

  • Page 7: Needle Cooling From Above

    Needle cooling from above Needle cooling from above WARNING Risk of injury from sharp and moving parts! Puncture or crushing possible. Switch off the machine before assembling the needle cooling. 2.1 Assembling the needle cooling Fig. 1: Assembling the needle cooling (1) ①...
  • Page 8 Needle cooling from above 5. Disassemble the rear cover (4). 6. Disassemble the handwheel (5). 7. Disassemble the belt cover (6). Fig. 2: Assembling the needle cooling (2) ⑧ ⑨ ⑩ (8) - Solenoid valve (10) - Throttle check valve (9) - Blanking plug 8.
  • Page 9 Needle cooling from above Fig. 4: Assembling the needle cooling (4) ⑭ ⑬ (13) - Walking foot (14) - Needle 16. Raise the sewing feet. 17. Remove the needle (14). 18. Disassemble the walking foot (13). Additional Instructions D867 - 01.0 - 04/2020...
  • Page 10 Needle cooling from above Fig. 5: Assembling the needle cooling (5) ⑮ ⑯ ⑮ ⑰ ⑱ (15) - Hose (17) - Block (16) - Hole (18) - Blow tube 19. Slide the block (17) with blow tube (18) and hose (15) onto the walking foot bar.
  • Page 11 Needle cooling from above Fig. 6: Assembling the needle cooling (6) ⑲ ⑳ ⑮ ⑯ (15) - Hose (19) - Guides (16) - Hole (20) - Oil pump holder 25. Feed the hose (15) through the guides (19). 26. Feed the hose (15) through the cutout of the oil pump holder (20). 27.
  • Page 12 Needle cooling from above Fig. 7: Assembling the needle cooling (8) ⑩ ⑮ (10) - Throttle check valve (15) - Hose 29. Shorten the hose (15) to the exact length that allows for the hose (15) to be connected to the throttle check valve (10). 30.

  • Page 13: Connecting The Needle Cooling

    Needle cooling from above 2.2 Connecting the needle cooling Fig. 8: Connecting the needle cooling ① ② ③ ① (1) - Cable (3) - PCB A2 (2) - Solenoid valve To connect the needle cooling: 1. Tilt the machine head. 2.

  • Page 14: Needle Cooling From Below

    Needle cooling from below Needle cooling from below WARNING Risk of injury from sharp and moving parts! Puncture or crushing possible. Switch off the machine before assembling the needle cooling. 3.1 Assembling the needle cooling Fig. 9: Assembling the needle cooling (1) ①...
  • Page 15 Needle cooling from below Fig. 10: Assembling the needle cooling (2) ⑩ ⑥ ⑨ ⑦ ① ③ ⑧ (1) - Solenoid valve (8) - Hose (3) - Throttle check valve (9) - Cable holder (6) - Valve block (10) - Cable duct (7) - Bracket 6.
  • Page 16 Needle cooling from below 12. Feed the hose (8) through cable holder (11). 13. Connect hose (8) with hose (14) using a plug nipple (12). 14. Feed the hose (14) through cable holder (13). 15. Erect the machine head. Fig. 12: Assembling the needle cooling (4) ⑲...

  • Page 17: Connecting The Needle Cooling

    Needle cooling from below 3.2 Connecting the needle cooling Fig. 13: Connecting the needle cooling ① ② ③ ④ ① (1) - Cable (3) - Solenoid valve (2) - Cable holder (4) - PCB A2 To connect the needle cooling: 1.

  • Page 18: Software Settings

    Software settings Software settings To activate the needle cooling in the software: 1. Log in as a technician. User: technician Password: 25483 The needle cooling has been preset in the software. Check anyway if the set value is correct. 2. Open the menu Navigation >...

  • Page 19: Appendix

    Appendix Appendix Wiring diagram Fig. 14: Wiring diagram, connection needle cooling Additional Instructions D867 - 01.0 - 04/2020...
  • Page 20 Appendix Additional Instructions D867 - 01.0 - 04/2020...
  • Page 22 DÜRKOPP ADLER AG Potsdamer Str. 190 33719 Bielefeld Germany Phone: +49 (0) 521 925 00 Email: service@duerkopp-adler.com www.duerkopp-adler.com...

Table of Contents