Related Manuals for DURKOPP ADLER M-TYPE 867 Series
Summary of Contents for DURKOPP ADLER M-TYPE 867 Series
- Page 1 867 M-TYPE Flatbed machines Additional Instructions Throat plate slide interrogator...
- Page 2 IMPORTANT READ CAREFULLY BEFORE USE KEEP FOR FUTURE REFERENCE All rights reserved. Property of Dürkopp Adler AG and protected by copyright. Any reuse of these contents, including extracts, is prohibited without the prior written approval of Dürkopp Adler AG. Copyright © Dürkopp Adler AG 2018...
- Page 3 Table of Contents General information ..............3 Assembling the throat plate slide interrogator......5 Connecting the throat plate slide interrogator ...... 10 Testing the functionality ............15 Additional Instructions 867 M-TYPE - 00.0 - 05/2018...
- Page 4 Table of Contents Additional Instructions 867 M-TYPE - 00.0 - 05/2018...
-
Page 5: General Information
General information General information This kit has been designed for CLASSIC and PREMIUM machines of the M-TYPE series. During sewing, the throat plate slide (3) abuts on the throat plate (1) and is held in place by the locking spring (2). The machine is ready for operation: Fig. - Page 6 General information Components of the kit Check whether the scope of delivery for kit 0867 151174 is correct prior to installation. The kit is comprised of the following parts: Part number Number Description 9815 710221 Sensor with cable 9840 120104 Cable holder 9840 121002 Cable tie...
-
Page 7: Assembling The Throat Plate Slide Interrogator
Assembling the throat plate slide interrogator Assembling the throat plate slide interrogator WARNING Risk of injury! Faulty assembly, e.g. faulty wiring, can cause the entire machine to malfunction. Only qualified specialists may assemble the throat plate slide interrogator. Do not assemble the throat plate slide interrogator unless the machine is switched off. - Page 8 Assembling the throat plate slide interrogator 2. Tighten the proximity switch (2) to the metal bracket (4) using the nuts and toothed washers: • The distance between the lower edge of the metal bracket (4) and the upper edge of the proximity switch (2) is 17 mm •...
- Page 9 Assembling the throat plate slide interrogator Important Make sure not to pinch off the oil line (8). Fig. 6: Assembling the throat plate slide interrogator (4) ⑧ ⑨ ⑨ ⑦ ⑨ (7) - Cable (9) - Clip (8) - Oil line 7.
- Page 10 Assembling the throat plate slide interrogator Removing the valve cover (CLASSIC) Fig. 7: Assembling the throat plate slide interrogator (5) ⑩ ⑪ (10) - Valve cover (11) - Screw 8. Loosen the screws (11). 9. Remove the valve cover (10). Removing the handwheel (PREMIUM) Fig.
- Page 11 Assembling the throat plate slide interrogator Removing the cover on the side (PREMIUM) Fig. 9: Assembling the throat plate slide interrogator (7) ⑭ ⑮ (14) - Cover on the side (15) - Screw 12. Loosen the screws (15). 13. Remove the cover on the side (14) and set it down carefully on the tabletop next to the machine.
-
Page 12: Connecting The Throat Plate Slide Interrogator
Connecting the throat plate slide interrogator Connecting the throat plate slide interrogator WARNING Risk of injury from sharp and moving parts! Crushing, cutting and punctures are possible. Do not connect the throat plate slide interrogator unless the machine is switched off and de-energized. Disconnect the machine from the power supply before connecting the interrogator. - Page 13 Connecting the throat plate slide interrogator To connect the throat plate slide interrogator: Assembling the circuit board (if not yet present on CLASSIC machines) Fig. 11: Connecting the throat plate slide interrogator (1) ④ ③ ② ① (1) - Bracket (3) - Screw (2) - Screw (4) - Circuit board...
- Page 14 Connecting the throat plate slide interrogator Assembling the circuit board (if not yet present on PREMIUM machines) Fig. 12: Connecting the throat plate slide interrogator (2) ⑥ ⑦ ④ ⑦ ④ ⑥ ⑤ - Circuit board (6) - Socket (not visible) (5) - Plug (of interrogator cable) (7) - Screw 4.
- Page 15 Connecting the throat plate slide interrogator Assembling the circuit board (if not yet present on shoe machines) Fig. 13: Connecting the throat plate slide interrogator (3) ④ ④ ⑦ ⑥ (4) - Circuit board 7. Assemble the circuit board at the top left on the back of the machine arm (4) using the socket (6) and the screw (7).
- Page 16 Connecting the throat plate slide interrogator Fig. 15: Connecting the throat plate slide interrogator (5) ⑭ ⑪ ⑬ ⑫ (11) - Plug connection X2-X5 (13) - DIP switch 1-5 (12) - Plug connection X6 (IN) (14) - Plug connection X1 8.
-
Page 17: Testing The Functionality
Testing the functionality Testing the functionality Order 1. Assemble the throat plate slide interrogator ( p. 5). 2. Connect the throat plate slide interrogator ( p. 10). 3. Test functionality. To test the functionality of the throat plate slide interrogator: 1. - Page 18 Testing the functionality Additional Instructions 867 M-TYPE - 00.0 - 05/2018...
- Page 20 DÜRKOPP ADLER AG Potsdamer Str. 190 33719 Bielefeld, Germany Germany Phone: +49 (0) 521 925 00 Email: service@duerkopp-adler.com www.duerkopp-adler.com...