Trane 20-80 ton water-cooled air conditioners 20-60 ton air-cooled air conditioners remote air-cooled condensers manual pkg-prc002-en intellipak signature series (101 pages)
12,000 Btu 150 = 15,000 Btu Electric heater Front and discharge grille Indoor coil PTAC-SVX01C-EN Model Number Description The model number helps owner/ operator, installing contractors, and service technicians to define the operation, components and options for a specific unit.
CAUTION Use Copper Conductors Only! Unit terminals are not designed to accept other types of conductors. Failure to use copper conductors may result in equipment damage. PTAC-SVX01C-EN...
Page 5
Obtain a chemical analysis of the refrigerant if necessary. Questions about recovered refrigerant and acceptable refrigerant quality standards are addressed in ARI Standard 700. PTAC-SVX01C-EN General Information Refrigerant Handling and Safety Consult the manufacturer’s material safety data sheet (MSDS) for...
• Ensure adequate sealing and insulation is around the wall sleeve. Figure 2. Minimum unit clearance Table 1. Minimum interior and exterior projections 42 1/2” min. 16 1/4” min. Finished Floor Dimension B Figure 3. Minimum wall opening dimensions PTAC-SVX01C-EN...
Remove access panels and check for interior component damage. Make specific notations concerning the damage on the freight bill. Do not accept delivery. PTAC-SVX01C-EN Pre-Installation Minimum projection 3 1/4 2 3/4 8 (4) 2-6” 50 -150 76-80 •...
Top of wall sleeve 5.00” 12.62 Bottom of wall sleeve Toe plate 0 to 3.0” long Figure 8. Hydronic kit side view PTAC-SVX01C-EN Unit Dimensions PTAC Wall Sleeve Steam inlet and outlet connection Steam/water (right hand coil connection) coil position 53-2/3”...
For variable frequency drives or other energy storing components provided by Trane or others, refer to the appropriate manufacturer’s literature for allowable waiting periods for discharge of capacitors. Verify with an appropriate voltmeter that all capacitors have discharged.
Page 13
Note: For installation procedures, please refer to the Installation Guide that accompanied the accessory. PTAC-SVX01C-EN Installation Step 4. Install wall sleeve in wall opening. For condensate to drain properly inside the unit, the sleeve must be installed properly: •...
Page 14
Universal Power Cord 15 Option 1. A field supplied 115 volt 15 amp receptacle is mounted in the building floor or wall. A Trane 115 volt 15 amp power cord BAYPCRD007 is connected to the PTAC and plugged into the receptacle.
Page 15
High Emgcy Heat Low Emgcy Heat PTHE Heat Pump Auxiliary is Electric only High Cooling Low Cooling High Fan Low Fan PTAC-SVX01C-EN Installation Table 7. Wiring Voltage Unit Mode High Heat Pump High Auxiliary Heat Low Auxiliary Heat PTEE Air Conditioner...
Page 16
The PTAC subcools the room to a preset state, a dehumidification offset below the cooling setpoint. The unit will automatically adjust the fan speed. When incorporating the vent door option, the controller will automatically adjust its position. PTAC-SVX01C-EN...
Page 17
In order for the user to access the configurable parameters, a digital display module must be present. The configuration set-up mode is entered by pressing and holding the "MODE" and "FAN" buttons simultaneously for 5 seconds. PTAC-SVX01C-EN Installation Table 9. Set point configuration Configuration Configuration step...
When the controller is in the occupied state, the unit runs space comfort control using the occupied setpoints. All heating/cooling/ ventilation features are enabled. PTAC-SVX01C-EN Installation Occupied Standby state When the controller is in occupied standby state, the unit runs space comfort control using the occupied standby setpoints.
Sensor The PTAC can accommodate a field- installed door switch and occupancy sensor to operate the energy management feature. PTAC-SVX01C-EN Operation Remote Thermostat Control Each unit can be operated from any standard 4 or 5-wire, remote- mounted thermostat. Also, the unit...
Page 22
See Figure 31. Rotate the grille 180° end-for- end. Reinstall the screws securing the discharge air grille to the cabinet front. Reinstall the cabinet front on the unit. Screws Figure 18. Discharge air grille PTAC-SVX01C-EN...
Page 23
Heating amps 208V 11.8 230V 13.4 265V 11.6 Certified in accordance with the Unitary Air-Conditioner Equipment Certification Program, which is based on ARI Standard 310/380. Notes: PTAC-SVX01C-EN Operation PTEE 09 8,800 9,000 8,700 12,000 11,600 11,800 11,800 11.5 11.4 11.4 11.3...
Page 28
UNIVERSAL POWER CORD 265 VOLT - 30 AMP Display Module DISPLAY MODULE (AMERICAN STANDARD LOGO STANDARD) DISPLAY MODULE (AMERICAN STANDARD LOGO & DEHUMIDIFICATION) DISPLAY MODULE (TRANE LOGO STANDARD) DISPLAY MODULE (TRANE LOGO & DEHUMIDIFICATION) Escutcheon Cover ESCUTCHEON COVER FOR FRONT PANEL (AMSTD LOGO)
Page 29
Extended standard base kick plate 7" to 13" Upgraded kick plate standard height 2" to 6" (Like the unit ventilator design) Upgraded kick plate extended height 7" to 13" (Like the unit ventilator design) Color Standard Soft Dove II Special Color PTAC-SVX01C-EN Operation...
It is advisable to remove the unit from the sleeve and thoroughly clean the basepan and condenser coil on a periodic basis. PTAC-SVX01C-EN Maintenance • If the unit is installed ocean side or in a corrosive atmosphere, its life may be greatly reduced by the corrosive environment.
1400°F . • SILVER SOLDER (Alloy of 30% silver, 38% copper, 32% zinc): use with fluoride base flux on copper to steel, brass to copper, steel to steel, or brass to steel. Recommended heat is approximately 1200°F . PTAC-SVX01C-EN...
Figure 22. Refrigeration sealed system — heat pump (air conditioning model Figure 23. Refrigeration sealed system — Heat pump (heat pump model) PTAC-SVX01C-EN Maintenance Evacuation CAUTION Fan Motor Overheat! Never test operation without the unit in the wall sleeve. A serious...
Page 34
Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Place discharge and inlet air thermostats Place inlet thermostat in center of grille Figure 24. Proper placement of discharge and inlet air thermostats PTAC-SVX01C-EN...
For best results, perform the test under peak load conditions. The air conditioner must operate at least 20 minutes on the HIGH COOL position before testing. PTAC-SVX01C-EN Maintenance Cooling Performance Test Record the following temperatures for the cooling performance test: •...
Page 36
Doing so could result in death, serious injury, or property damage. If the test indicates shorted, grounded or open windings, see procedure for the next steps to be taken. PTAC-SVX01C-EN...
Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. PTAC-SVX01C-EN Maintenance With no power and compressor leads removed: Set an ohmmeter on its highest scale.
Page 39
The serviceman must be familiar with the operational characteristics of the product and should not jump to conclusions. PTAC-SVX01C-EN Maintenance Temperature-Actuated Drain Valve (model PTHE Only) The PTHE is equipped with a temperature-actuated drain valve located in the base pan.
Page 40
Reinstall the sheet metal cover over the control board. Position the front cabinet over the chassis and push the sides until the retaining clips engage. Figure 28. Power jumper PTAC-SVX01C-EN...
The last step of the sequence resets the controller. See the Manual output test section on page 22 for more information about the manual output test. PTAC-SVX01C-EN Troubleshooting Cycling Power When someone turns off the controller’s power, then re-applies power, the unit cycles through a power up sequence.
Page 42
During the active defrost cycle the outdoor fan is controlled off. See the section on defrost control. Unit wiring The wiring between the controller outputs and the fan relays and contacts must be present and correct for normal fan operation. Troubleshooting PTAC-SVX01C-EN...
Page 43
The wiring between the controller output and the ventilation must be present and correct for normal operation. Normal operation See the section on Ventilation operation. Defrost Cycle During the active defrost cycle the outdoor fan is controlled off. See the section on defrost control. PTAC-SVX01C-EN Troubleshooting...
Page 44
The indoor fan continues to run after the compressor or auxiliary heat will be on. Table 39. Control fuse is blown Symptom The generic thermostat does not work The energy input does not work The ventilation input does not work The remote fan output does not work Troubleshooting PTAC-SVX01C-EN...
3) For different electric heater capacity, refer to IOM for power cord selection. 4) The specs for the control board fuse are: 5 x 20mm, 250V, 315mA, fast acting. Figure 29. 230/208V wiring diagram (07 models) PTAC-SVX01C-EN Wiring Diagram K8 HEAT K9 COOL Rev Valve...
Page 46
8 7 6 5 4 3 2 1 YL/GR 1.0KW 2.0KW 2.0KW RD - RED GR - GREEN WH - WHITE BK - BLACK OR - ORANGE YL - YELLOW FACTORY WIRING BL - BLUE FIELD WIRING BR - BROWN PTAC-SVX01C-EN...
Page 47
3) For different electric heater capacity, refer to IOM for power cord selection. 4) The specs for the control board fuse are: 5 x 20mm, 250V, 315mA, fast acting. Figure 31. 265V Wiring diagram (07 models) PTAC-SVX01C-EN Wiring Diagram K8 HEAT K9 COOL Rev Valve...
Page 48
8 7 6 5 4 3 2 1 YL/GR RD - RED GR - GREEN WH - WHITE INDOOR MOTOR BK - BLACK OR - ORANGE YL - YELLOW FACTORY WIRING BL - BLUE FIELD WIRING BR - BROWN PTAC-SVX01C-EN 1.0KW 2.0KW 2.0KW...
Page 49
R W Y GH GL O VT EN Figure 33. Energy management system R W Y GH GL O VT EN Figure 34. 3rd party class 2 thermostat wiring Figure 35. Remote display wiring PTAC-SVX01C-EN Wiring Diagram...
Warranty Full 1st Year Warranty Trane will repair or replace any part which proves to be defective due to workmanship or materials, free of charge. This includes parts and labor. Full 2nd - 5th Sealed System Warranty Trane will repair or replace the...
Page 52
Literature Order Number PTAC-SVX01C-EN Date 09/06 Supersedes PTAC-SVX01B-EN Stocking Location Webb/Mason The manufacturer has a policy of continuous product and product data improvement and reserves the right to change design and specifications without notice.