Page 3
EVO 3 (reference code: S042) other names: EVO 3 – EVO3 FWD – EVO3 RWD – EVO 3 FWD – EVO 3 RWD satisfies the requirements laid down by the European Directive 93/42; according to the criteria for classification of Annex IX of this Directive, it is classified as: class I medical device;...
Index PRODUCT INFORMATION ....................... 1 PREPARATION FOR FIRST USE ....................2 Checks to be made on delivery ..................2 Unpacking ........................2 Software description ....................... 3 ADJUSTMENTS ........................4 Seating system description ....................4 List of adjustments ......................6 3.2.1 Version of the wheelchair with biomechanics movements ........
Page 5
Manual brake release lever ................... 43 Use as seat in a motor vehicle ..................45 4.3.1 Securing the wheelchair with Four points tie-down system ........52 4.3.2 Dahl engineering docking station ................54 Powered functions ......................56 Main switch ........................63 Battery charging ......................
Page 6
5.7.15 Armrest ......................... 115 SPECIFICATIONS ........................117 Maximum user weight ....................118 Other provided information ..................119 Dimensions ........................120 6.3.1 - Version with biomechanical movements ............120 6.3.2 - Version with biomechanical movements ............121 Warranty terms ........................122 Serial number ......................
Page 7
Symbols in this manual WARNING This symbol means presence of danger for the user or damage for the product. Always follow instructions when this symbol is present. PINCH HAZARD This symbol means presence of pinch hazard. ELECTRICAL WARNING This symbol means presence of danger related to the presence of electrical energy.
Page 8
TEMPERATURE The temperature of some surfaces may increase when the product is exposed to external heat sources as direct sunlight. TIPPING HAZARD Tipping hazard is strongly reduced because of the design of the product according to EN 12182. In any case, please pay special attention during the adjustments and use of the product to prevent any damage to the user or product itself.
Page 9
ELECTROMAGNETIC RADIATION DANGER The behavior of the wheelchair while driving may be affected by electromagnetic fields created by transceivers such as: Citizens band (CB) radios, walkie-talkies, fire and police radios, cellular phones, lap-top computers, commercial radio and television broadcast antennas. PLEASE USE CAUTION in the presence of these devices.
Page 10
Service manual is intended for technical personnel to maintain and repair wheelchairs. It is important to follow the instructions contained in this manual in order to professionally work with the product. The qualified personnel who works with wheelchairs must comply with all provisions of occupational safety and common sense in order to preserve his own safety.
Page 11
MANUFACTURER For any need not expressly explained in this manual, please contact the manufacturer. Neatech.it SRL via A. de Curtis 4/A, 80040, Cercola (NA), Italy www.neatech.it –...
1 PRODUCT INFORMATION The EVO 3 offers a sleek design and superior performance, the top of its category, providing a perfect combination of stability and maneuverability. Born from the passion of Neatech for high engineering, which allows it to offer a broader spectrum of choices than in the past;...
The wheelchair is delivered already mounted and ready to use. Before starting to use the wheelchair please check if all described components are present. If not, please contact as soon as possible the vendor. PACKAGING DISPOSAL To properly recycle the packaging materials follow instructions provided by your local waste disposal service. www.neatech.it 2/122...
Programming must be conducted only by qualified personnel with in- depth knowledge of the wheelchair and power module system. Any change to this part of the software may result in a hazardous situation for the user. www.neatech.it 3/122...
(g). • Legrest angle (H): this is the angle between the legrest and the line perpendicular to the chassis of the wheelchair (line m). Only when seat angle is zero, absolute legrest angle is equal to legrest angle. www.neatech.it 4/122...
C - Service Armrests height B - Assistant Horizontal armrest angle B - Assistant Vertical armrest angle B - Assistant Footplates height Service Manual C - Service Backrest height B - Assistant Joystick position B - Assistant Table 2 www.neatech.it 6/122...
3.10 B - Assistant Armrests height 3.11 B - Assistant Sidepad height 3.12 B - Assistant Footplates height 3.13 B - Assistant Footplates angle and depth 3.14 B - Assistant Joystick position 3.15 B - Assistant Table 3 www.neatech.it 7/122...
It is not easy to provide a range for this adjustment because there are too many configuration and possibilities. Average needed Difficulty level: time: Easy <5 min WARNING As this adjustment is carried out, it is necessary to compensate by adjusting also the armrest vertical angle. www.neatech.it 8/122...
Page 20
• Adjust the bolt shown in figure in order to adjust armrests height. Rotate it clockwise to rise the ALLEN WRENCH armrest and counterclockwise to lower it. 5 mm • When finished, tighten again the 4 screws previously loosen. www.neatech.it 9/122...
It is not easy to provide a range for this adjustment because there are too many configuration and possibilities. Average needed Difficulty level: time: Easy <5 min RIGHT AND LEFT SIDE It is possible to adjust separately left and right side. Figure 6 • Unscrew the nut shown in figure. www.neatech.it 10/122...
Page 22
Figure 7 • Rotate the screw shown in figure clockwise to lower the armrest or rotate it counterclockwise to rise the armrest. www.neatech.it 11/122...
RIGHT AND LEFT SIDE It is possible to adjust separately left and right side. Figure 8 • Unscrew the screw shown in figure. ALLEN WRENCH • Set the armrest angle as desired. 4 mm • Screw again the screw. www.neatech.it 12/122...
M3 P2 - S042-V391 66.0 cm M4 P3 – S042- V394 M4 P1 – S042- 51.0 cm V383 55.0 cm 59.0 cm M4 P1 – S042- 63.0 cm V392 Table 4 Average needed Difficulty level: time: Easy 20 min www.neatech.it 13/122...
Page 25
Figure 9 • Remove the backrest upholstery. • Unscrew the 4 screws shown in figure. OPEN-END WRENCH • Adjust the height as desired. 8 mm • Screw again the screws. • Mount again the backrest upholstery. www.neatech.it 14/122...
Difficulty level: time: Easy <5 min 3.7.1 Standard support - Depth Figure 10 • Unscrew the 2 screws shown in figure. ALLEN WRENCH • Adjust the depth of the joystick as desired. 5 mm • Screw again the screws. www.neatech.it 15/122...
Figure 11 3.7.2 Retractable support S045-V263 - Depth Figure 12 • Unscrew the 2 screws shown in figure. ALLEN WRENCH • Adjust the depth and the height of the joystick as 5 mm desired. • Screw again the screws. www.neatech.it 16/122...
485 mcm M4 - S042-V071 485 mm 520 mm Table 5 WARNING It is needed to set separately left and right seat depth. Always set them at the same manner. Average needed Difficulty level: time: Easy 5 min www.neatech.it 17/122...
Page 29
Figure 13 • Remove the backrest. • Loosen the 6 screws shown in figure. • Set the backrest according to the desired seat depth. OPEN-END WRENCH 10 mm • Tight again the 6 screws. • Mount again the backrest. www.neatech.it 18/122...
It is needed to set separately left and right backrest angle. Always set two parts of backrest at the same manner. Average needed Difficulty level: time: Easy 5 min Angle adjustable with pistons Use the lever located on the push bar to move the backrest. www.neatech.it 19/122...
Page 31
• Screw again screws. ADDITIONAL ADJUSTMENT After adjusted the angle of backrest as described above it is possible to adjust of more 5° simply acting on the axis shown in figure. Figure 15 www.neatech.it 20/122...
RIGHT AND LEFT SIDE It is possible to adjust separately left and right armrest. Average needed Difficulty level: time: Easy 5 min RANGE Please be sure that the chosen position doesn't represent an obstacle. Figure 16 www.neatech.it 21/122...
Page 33
• Loosen the lever shown in figure and remove the armrest. Figure 18 • Loosen the 2 screws shown in figure and set the ALLEN WRENCH depth of armrest clamp as desired. 4 mm • Tighten again the 2 screws and put back the armrest. www.neatech.it 22/122...
Page 34
ADDITIONA ADJUSTMENT Moreover it is possible to adjust armrest depth unscrewing the 2 screws shown in figure with a 4 mm allen wrench. Figure 19 www.neatech.it 23/122...
RIGHT AND LEFT SIDE It is possible to adjust separately left and right armrest. Average needed Difficulty level: time: Easy <5 min SIDEPAD, JOYSTICK AND ARMREST HEIGHT It is better to adjust first armrest height, then joystick and finally the sidepad. www.neatech.it 24/122...
Page 36
Figure 20 • Loosen the 2 screws shown in figure. ALLEN WRENCH • Set the armrest according to the desired height. 4 mm • Tight again the 2 screws. www.neatech.it 25/122...
RIGHT AND LEFT SIDE It is possible to adjust separately left and right sidepad. SIDEPAD, JOYSTICK AND ARMREST HEIGHT It is better to adjust first armrest height, then joystick and finally the sidepad. Average needed Difficulty level: time: Easy <5 min www.neatech.it 26/122...
Page 38
Please be sure that the chosen position doesn't represent an obstacle for armrest. Figure 21 Figure 22 • Unscrew the 2 screws shown in figure and set the ALLEN WRENCH position of sidepad as desired. 3 mm • Screw again the 2 screws. www.neatech.it 27/122...
Angle adjustable 27.5 cm 30.0 cm 32.5 cm 35.0 cm 37.5 cm RIGHT AND LEFT SIDE It is possible to adjust separately left and right legrest if you have splitted footrest. Average needed Difficulty level: time: Easy <5 min www.neatech.it 28/122...
Page 40
6 mm 13 mm open-end wrench. • Repeat the operation for both left and right side of the wheelchair. • Set the position of the footplate according to OPEN-END WRENCH 13 mm desired height. • Screw again the screws. www.neatech.it 29/122...
In any case it is always possible to choose between 3 different depth. RIGHT AND LEFT SIDE It is possible to adjust separately left and right legrest if you have splitted footrest. Average needed Difficulty level: time: Easy <5 min www.neatech.it 30/122...
Page 42
Tighten again the screws. Depth adjustment Figure 25 • Unscrew the 2 screws shown in figure. ALLEN WRENCH • Set the position of the footplate according to desired depth. 4 mm • Screw again the screws. Screw again the 2 screws. www.neatech.it 31/122...
3.15.1 Standard support - Depth and height Figure 26 • Unscrew the 2 screws shown in figure. ALLEN WRENCH • Adjust the depth and the height of the joystick as 4 mm desired. • Screw again the screws. www.neatech.it 32/122...
3.15.1 Retractable support - Depth and height Figure 28 • Unscrew the 2 screws shown in figure. ALLEN WRENCH • Adjust the depth and the height of the joystick as 4 mm desired. • Screw again the screws. www.neatech.it 33/122...
Default position means that all adjustable parts of the wheelchair are set in the most stable and safe configuration ADJUSTABLE PARTS VALUE NOTES Seat angle 0° Backrest angle 90° Legrest angle 90° Or minimum Seat height 0 cm Table 6 www.neatech.it 34/122...
INFORMATION Do not install, maintain or operate the product without reading all warnings and this entire manual. Always keep this manual in connection with the product. INFORMATION The wheelchair is designed for use mostly in indoor environments. www.neatech.it 35/122...
Page 47
Do not stand on the frame of the wheelchair. Some pathologies may limit your ability to use your wheelchair safely. Be sure to consult with a doctor about your physical limitations. Please practice your drive ability under the supervision of an assistant. www.neatech.it 36/122...
Page 48
MAX 6° Figure 29 Dealing with downhill When facing a downhill road it is recommended to set the seating system to default position. It is better to use a drive profile with low speed MAX 6° Figure 30 www.neatech.it 37/122...
Page 49
When facing with side slopes, always use the wheelchair with great caution and make sure the seating system is in the default position. MAX 6° Figure 31 Turning with the wheelchair When turning with the wheelchair, always use great caution. www.neatech.it 38/122...
Page 50
Transfer into and out the wheelchair Users transfer is recommended with the presence of an assistant. Don’t use footrests or armrests as support. Always turn off the wheelchair before transfer. www.neatech.it 39/122...
Page 51
Do not lift the wheelchair with a user on board. Do not lift the wheelchair grabbing the legrests. If you really need to lift the wheelchair, it is suggested to grab it with the help of at least one other people. Grab the wheelchair using the tie down shown in figure. Figure 33 www.neatech.it 40/122...
Use the function PROFILE to change different types of profiles: they are sorted from the more indoor ones to the more outdoor ones. For each profile it is possible to change the speed. www.neatech.it 41/122...
Page 53
Use this function to see total and partial distance made with the wheelchair. It is also possible to reset partial distance. Backlight It is possible to adjust backlights of the screen. Background Use this function to choose the color of background of the display. www.neatech.it 42/122...
When the brakes are released. it is not possible to drive the wheelchair. Figure 35 UNLOCKED LOCKED LOCKED UNLOCKED WARNING When the brakes are released never use the wheelchair on a slope or a wet surface. Don’t operate the brake release without the presence of an assistant. www.neatech.it 43/122...
Page 55
WARNING The drive system should be re-engaged before an occupant is left unattended or attempts to operate the wheelchair. WARNING Always act on both left and right manual release levers. www.neatech.it 44/122...
• The pelvic belt should be worn low across the front of the pelvis, so that the angle of the pelvic belt is within the preferred zone of 30° to 75° to the horizontal, similar to that shown in figure. Figure 36 www.neatech.it 45/122...
Page 57
In order to mount pelvic belt on the wheelchair, firstly mount the fixing plate as shown in figure. Use socket head cap screw M6x10 and a 5 mm allen ALLEN WRENCH 5 mm wrench. Repeat operation for both left and right side of the wheelchair. www.neatech.it 46/122...
Page 58
Firstly mount the fixing plate as shown in OPEN-END figure. WRENCH Use hushroom head square neck bolt screw M5x16 DIN 8 mm 603, M5 nut, and a 8 mm open-end wrench. Repeat operation for both left and right side of the wheelchair. www.neatech.it 47/122...
Page 59
WARNING: Safety of wheelchair and user can't be assured when the movement of gas springs is not correctly locked while using the wheelchair as a seat in a motor vehicle. Figure 40 www.neatech.it 48/122...
Page 60
When possible other auxiliary wheelchair equipment should be either secured to the wheelchair or removed from the wheelchair and secured in the vehicle during travel, so that it does not break and cause injury to vehicle occupants in the event of a collision. www.neatech.it 49/122...
Page 61
Alterations or substitutions should not be made to the wheelchair securement points or to structural and frame parts or components without consulting the wheelchair manufacturer. WARNING Wheelchair has sealed type batteries. Never use different battery type when used in a motor vehicle. www.neatech.it 50/122...
Page 62
WARNING Care should be taken when applying the occupant restraint to position the seatbelt buckle so that the release button will not be contacted by wheelchair components during a crash. www.neatech.it 51/122...
Use the tie down points marked with the symbol shown in figure.Hook the wheelchair in 4 points: two in the front part and two in the rear part. Figure 42 Use the tie down pointsHook the wheelchair in 4 points: two in the front part and two in the rear part. www.neatech.it 52/122...
Page 64
Tie down straps should form angles shown below. PREFERRED ANGLES OF FRONT PREFERRED ANGLES OF REAR WHEELCHAIR WHEELCHAIR TIE DOWN STRAPS TIE DOWN STRAPS 40° 30° 45° 60° 25° 25° 10° 10° Figure 43 Figure 44 WARNING Always use four tie down straps. www.neatech.it 53/122...
Do not attempt to reverse out the docking station until the red LED on the control module, which indicates the unlock position, has been illuminated. Move the wheelchair away from the docking station within this 5-second period. www.neatech.it 54/122...
Page 66
If this happens repeat above ulocking procedure. Figure 46 CONTACT INFORMATION For more information contact the manufacturer of the wheelchair or the manufacturer of the docking station. Dahl Engineering Løvevej 3 DK-7700 Thisted Tel. +45 96 18 00 77 https://dahlengineering.dk sales@dahlengineering.dk www.neatech.it 55/122...
Move the joystick rearward while you are in seating mode and the desired function is selected INFORMATION An authorized service center is able to customize seating functions according specific needs of single user. PINCH HAZARD When using powered seating functions, always pay special attention to reduce pinch risk. www.neatech.it 56/122...
Page 68
For these reasons it is very important to not use the legrest function on a non-flat surface or near steps or obstacles. www.neatech.it 57/122...
Page 69
The movement stops when seat height is 0 cm. When the movement stops you will hear a sound. www.neatech.it 58/122...
Page 70
An authorized service center is able to adjust the angles shown in figure. When the movement stops you will hear a sound. Figure 52 MOVE DOWN it is possible to bring back the wheelchair to the default position shown in Figure 53. Figure 53 www.neatech.it 59/122...
Page 71
An authorized service center is able to adjust the angles shown in figure. When the movement stops you will hear a sound. Figure 54 MOVE DOWN it is possible to bring back the wheelchair to the default position shown in Figure 55. Figure 55 www.neatech.it 60/122...
Page 72
An authorized service center is able to adjust the angles shown in figure. When the movement stops you will hear a sound. MOVE DOWN Figure 56 it is possible to bring back the wheelchair to the default position shown in Figure 57. Figure 57 www.neatech.it 61/122...
Page 73
An authorized service center is able to adjust the angles shown in figure. When the movement stops you will hear a sound. MOVE DOWN it is possible to bring back the wheelchair to the default position shown in Figure 59. Figure 59 www.neatech.it 62/122...
If the power chair suddenly stops, use the switch to connect again batteries to the power module and turn on again the wheelchair. If the problem still continues, it means that there is some electric fault. Check for any damaged cables or any damage in connections, for more information see section 5.4. www.neatech.it 63/122...
Page 75
If the switch operates, often this means that there is a major electrical fault. The cause of fault should be checked carefully. For more information, please contact the manufacturer. www.neatech.it 64/122...
• When batteries are loaded unplug the power cord and the battery cable from the joystick. RUNNING-IN PERIOD Typically, batteries are able to offer 100% performance after about 15-20 cycles. CHARGER SPECIFICATION 24 V MIN 6 A MAX 10 A - Charging profile for GEL batteries www.neatech.it 65/122...
Page 77
Check if charger requirements data matches with the network power (voltage, frequency) RELEASE DANGER Any impact to the batteries could cause a loss of fluids. Please pay special attention. BATTERIES DISPOSAL To properly recycle the batteries follow instructions provided by your local waste disposal service. www.neatech.it 66/122...
If you transport the wheelchair with motors disengaged, the wheelchair is free to move. This may result in a hazardous situation. 4.7.1 Batteries removal Figure 62 ALLEN WRENCH • Unscrew the 4 screws shown in figure. 3 mm • Remove the cover. www.neatech.it 67/122...
Page 79
• Unplug the connectors shown in figure. Figure 64 • Unscrew the 4 screws shown in figure. ALLEN WRENCH • Remove the metalsheet with mounted modules. It 4 mm is not necessary to unplug any wires. • Pull away the batteries pack. www.neatech.it 68/122...
Page 80
Figure 65 • Unscrew the 4 screws shown in figure. WARNING Batteries are mounted in a metal enclosure. Total weight is about 40 kg. Please do not remove batteries from their enclosure. Please pay special attention. www.neatech.it 69/122...
Page 81
It is not possible to provide a universal package, so the user should provide himself for it. The used package must be water and dust resistant and strong enough to protect the wheelchair from any hurts. When inserting the wheelchair into the package protect any protruding parts with some foam or similar. www.neatech.it 70/122...
To clean the wheelchair do not use high-pressure water spray devices. For plastic and metal parts use a soft cloth dampened with mild detergent. For the upholstery, linings, seat and back covers use warm water and mild detergent. Do not use stain removers, solvents, acids, etc. www.neatech.it 71/122...
250 kPa. Check if the lever of the main Weekly B - Assistant switch works correctly Check tire usury Monthly B - Assistant Check brake release lever Monthly B - Assistant Check aging of batteries Monthly C – Service www.neatech.it 72/122...
5.3 Tire puncture 5.3.1 User information Traction wheels Figure 67 • Lift the wheelchair. ALLEN WRENCH • Unscrew the 4 screws shown in figure. 6 mm • Remove the wheel. www.neatech.it 73/122...
Page 85
5 mm Contact an authorized service center for the repair or the substitution of the damaged wheel. When the authorized service center gives you back the repaired wheel or a new one, mount it following instructions in reverse order. www.neatech.it 74/122...
Page 86
INFORMATION With wheels Ø320 S042-V620 it is necessary to mount the screws of the castor in holes (A). With wheels 3.00-8 it is necessary to mount the screws of the castor in holes (B). Figure 69 www.neatech.it 75/122...
Page 87
Castor Pneumatic black Ø200 mm x 50 mm R042-0132A Tire of castor gray Ø200 mm x 50 mm R042-0132B Tire of castor black Ø200 mm x 50 mm R042-0133 Tube for castor Ø200 mm x 50 mm Table 7 www.neatech.it 76/122...
5.5 Batteries replacement Figure 71 ALLEN WRENCH • Unscrew the 4 screws shown in figure. 3 mm • Remove the cover. www.neatech.it 78/122...
Page 90
• Unplug the connectors shown in figure. Figure 73 • Unscrew the 4 screws shown in figure. ALLEN WRENCH • Remove the metalsheet with mounted modules. It 3 mm is not necessary to unplug any wires. • Pull away the batteries pack. www.neatech.it 79/122...
Page 91
Figure 74 • Pull away batteries. WARNING Batteries are mounted in a metal enclosure. Total weight is about 40 kg. Please do not remove batteries from their enclosure. www.neatech.it 80/122...
Page 92
Figure 75 ALLEN WRENCH • Unscrew the 4 screws shown in figure. 3 mm • Remove the metallic handle. www.neatech.it 81/122...
Page 93
Figure 76 • Remove cables from the batteries. ALLEN WRENCH • Mount new batteries following instructions in 5 mm reverse order. WARNING Each battery weights about 18 kg. Please pay special attention. www.neatech.it 82/122...
Page 94
Figure 77 BATTERIES SPECIFICATION 2 x 12 V – 50 Ah – GEL Type MAX 228 mm x 139 mm x 235 mm (h) Code Description Type of Notes operation Batteries R042-0110 www.neatech.it 83/122...
The product is suitable for reuse. Before dispensing it, the product must be cleaned, and subjected to maintenance. The operating instructions are included in this manual and must also be provided when the product is passed on. WARNING This operation must be performed only at an authorized service center. www.neatech.it 84/122...
R042-0210 Power module R042-0220 Seat module R042-0230 Charger R042-0250 Kit light for castor R042-0251 Light for castor R042-0252 Castor cover R042-0270 Mudguard kit R042-0271 Light for mudguard R042-0280 Bumpers for motors R042-0290 Gyroscope R042-0300 Light module Table 9 www.neatech.it 85/122...
Page 97
The use of spare parts or accessories not approved by the manufacturer may make the wheelchair unstable or uncontrollable. For each order, always contact an authorized service center. CONTACT INFORMATION For any other part not described in this manual please contact the manufacturer. www.neatech.it 86/122...
Average needed Difficulty level: time: Easy 5 min Figure 78 • Unscrew the screws shown in figure. • Substitute the wheel. SCREWDRIVER • Screw the new screws. • Repeat operations for both left and right side of the wheelchair. www.neatech.it 87/122...
Page 99
Code Description Type of Notes operation R042-0140 Antitip wheel Code Quantity R042-0140 R042-0140 Figure 79 www.neatech.it 88/122...
In case of problems with the seating system, please contact the manufacturer. Figure 80 • Lift the seat and raise legrest. • Unscrew the screws shown in figure. ALLEN WRENCH 3 mm • Substitute the cover. • Screw the new screws. www.neatech.it 89/122...
Page 101
Code Description Type of Notes operation R042-0150 Cover A Code Quantity R042-0150 R042-0150 Figure 81 www.neatech.it 90/122...
5.7.3 Cover B Average needed Difficulty level: time: Easy 5 min Figure 82 • Unscrew the screws shown in figure. ALLEN WRENCH • Substitute the cover. 3 mm • Screw the new screws. www.neatech.it 91/122...
Page 103
Code Description Type of Notes operation R042-0160 Cover B Code Quantity R042-0160 R042-0160 Figure 83 www.neatech.it 92/122...
Remove the joystick. Figure 85 • Unscrew the 2 screws shown in figure. Unscrew the 2 screws shown in figure. ALLEN WRENCH • Substitute the joystick support. 3 mm • Mount the old joystick following instructions in reverse order. www.neatech.it 93/122...
Page 105
Code Description Type of Notes operation R042-0190A Standard joystick support Code Quantity R042-0190 A R042-0190 A R042-0190 A R042-0190 A R042-0190 A R042-0190 A R042-0190 A R042-0190 A Figure 86 R042-0190 A R042-0190 A R042-0190 A www.neatech.it 94/122...
• Unscrew the 2 screws shown in figure. ALLEN WRENCH 3 mm • Remove the joystick. Figure 88 • Unscrew the 2 screws shown in figure. • Substitute the joystick support. ALLEN WRENCH 3 mm • Mount the old joystick following instructions in reverse order. www.neatech.it 95/122...
Page 107
Code Description Type of Notes operation R042-0190B Retractable joystick support Code Quantity R042-0190B R042-0190B R042-0190B R042-0190B R042-0190B R042-0190B R042-0190B Figure 89 www.neatech.it 96/122...
• Unscrew the 2 screws shown in figure. ALLEN WRENCH 4 mm • Substitute the joystick. Retractable joystick support Figure 91 • Unscrew the 2 screws shown in figure. Unscrew the 2 ALLEN WRENCH screws shown in figure. 3 mm • Substitute the joystick support. www.neatech.it 97/122...
Page 109
Code Description Type of Notes operation R042-0200 Standard joystick support Joystick Code Quantity R042-0200 Figure 92 www.neatech.it 98/122...
Difficulty level: time: Easy 10 min Figure 93 ALLEN WRENCH • Unscrew the screws shown in figure. 3 mm • If desired substitute the cover. Figure 94 • Unscrew the glass shown in figure. • Unplug the light. www.neatech.it 99/122...
Page 111
Figure 95 ALLEN WRENCH • Unscrew the screw shown in figure. 3 mm • Substitute the parts shown in figure. Code Description Type of Notes operation R042-0250 Kit light for castor R042-0251 Light for castor R042-0252 Castor cover www.neatech.it 100/122...
Difficulty level: time: Easy 10 min Figure 97 • Unscrew the glass shown in figure. • Unplug the light. Figure 98 ALLEN WRENCH • Unscrew the screw shown in figure. 4 mm • Substitute the parts shown in figure. www.neatech.it 102/122...
10 min Figure 100 • Unscrew the screws shown in figure. • Substitute the bumper for motor. Substitute the ALLEN WRENCH bumper for motor. 4 mm • Repeat operations for both left and right side of the wheelchair. www.neatech.it 104/122...
Page 116
Code Description Type of Notes operation R042-0280 Bumpers for motors Code Quantity R042-0280 R042-0280 Figure 101 www.neatech.it 105/122...
5.7.10 Legrest cover Average needed Difficulty level: time: Easy 5 min Figure 102 • Remove the seeger shown in figure. Use a SCREWDRIVER screwdriver as a lever. • Substitute the cover. www.neatech.it 106/122...
Page 118
Code Description Type of Notes operation R042-0311 Legrest cover Code Quantity R042-0311 R042-0311 Figure 103 www.neatech.it 107/122...
5.7.11 Footplate Average needed Difficulty level: time: Easy 5 min Figure 104 • Remove seeger shown in figure. Use a screwdriver as SCREWDRIVER a lever. • Substitute footplate. www.neatech.it 108/122...
Page 120
Code Description Type of Notes operation R042-0320 Footrest Code Quantity R042-0320 R042-0320 Figure 105 www.neatech.it 109/122...
5.7.13 Ruler for armrest adjustment Average needed Difficulty level: time: Easy 10 min Figure 108 ALLEN WRENCH • Unscrew the screw shown in figure. 4 mm Figure 109 SCREWDRIVER • Unscrew the part shown in figure. www.neatech.it 111/122...
Page 123
Figure 110 • Substitute parts shown in figure. Code Description Type of Notes operation R042-0372 Ruler for armrest adjustment Code Quantity R042-0372 R042-0372 R042-0372 R042-0372 R042-0372 R042-0372 Figure 111 R042-0372 R042-0372 www.neatech.it 112/122...
5.7.14 Armrest joint Average needed Difficulty level: time: Easy 10 min Figure 112 • Loosen the 2 screws shown in figure. ALLEN WRENCH 5 mm • Substitute the armrest. Code Description Type of Notes operation R042-0380 Armrest www.neatech.it 113/122...
5.7.15 Armrest Average needed Difficulty level: time: Easy 5 min Figure 114 • Loosen the 2 screws shown in figure. ALLEN WRENCH 5 mm • Remove the armrest. www.neatech.it 115/122...
Page 127
Code Description Type of Notes operation R042-0380 Armrest Code Quantity R042-0380 R042-0380 R042-0380 Figure 115 www.neatech.it 116/122...
It is possible to use the wheelchair when the temperature is between -10 °C and +40 °C. It is possible to store the wheelchair in a place with a temperature between -20 °C and +45 °C. www.neatech.it 117/122...
6.2 Other provided information Manufacturer Neatech.it srl Address via A. de Curtis 4/A – 80040 – Cercola (NA) - Italy Model S042 – Evo3 Description Value 110 cm Overall length with legrest 56.0 cm Overall width Folded length N.A. Folded width N.A.
340 mm 380 mm 420 mm 560 mm 495 mm 535 mm 575 mm 615 mm MIN 270 mm – MAX 480 mm Wheels Ø320: 46.0 cm Wheels 3.00-8: 48.0 cm FWD: 945 mm FWD: 1100 m m www.neatech.it 120/122...
MAX 420 mm MAX 460 mm MAX 500 mm MAX 520 mm 230 mm – 300 mm MIN 150 mm – MAX 480 mm Wheels Ø320: 46.0 cm Wheels 3.00-8: 48.0 cm FWD: 945 mm FWD: 1100 mm www.neatech.it 121/122...
The warranty expires in case of tampering, improper storage, unauthorized or incorrect maintenance. 7.1 Serial number For any report or assistance request, please communicate the serial number mentioned on the label in the position shown in figure. Figure 116 www.neatech.it 122/122...