Auto Channel Setting; Manual Channel Setting - Philips VR1100/02X User Manual

Auto Channel Setting

If you move to another place, you may
need to tune the VCR tuner again for
your new residential area.
1
Perform Auto Channel Set
1 Press VCR.
2 Press MENU.
3 Press 5 or ∞ to select "AUTO
TUNER SET UP", then press
OK/STATUS.
4 Press 5 or ∞ to select your country's
name, then press OK/STATUS.
5 Press 5 or ∞ to select your preferred
language, then press OK/STATUS.
6 Press 5 or ∞ to select "AUTO CH.
SET", then press OK/STATUS. The
Auto Set screen appears as below;
AUTO CH. SET
PLEASE WAIT
0 – – – – – + – – – – – – – – + – – – – – +
END : MENU
Beginning
The Auto Set screen appears, and
remains on screen while the recorder
searches for receivable stations.
As Auto Channel Set progresses,
the " " mark on the screen moves
from left to right.
Wait until the screen as shown in step 2
appears.
Confirm Programmed Channel
2
Information List
Once it is completed, "AUTO CH. SET
COMPLETED" is displayed on the
screen for about 5 seconds.
The following screen will appear after
5 seconds, or if you press MENU;
PR CH ID PR CH
01 25 ARD 08 C26 E-SP
02 C08 SKY1 09 C33 3SAT
03 10 ZDF 10 55
04 C65 RAI1 11 C24 SAT1
05 C31 BBC1 12 C23 OSF
06 C32 BBC2 13 C25 ESPN
07 C24 BBC4 14 C48 20G
SELECT : 5 ∞
EDIT : OK
ERASE : CLEAR
END : MENU
C: Cable
PR: channel positions
CH: channel numbers
ID: station names ( P.19)
• The blueback screen and the
programme currently being broad-
cast by the blinking station
apppear alternately for 8 seconds each.
• To view the next page, use the 5∞
2 3 buttons on the remote control.
The stations located in the selected
country appear at the top of the list.
• The Guide Program numbers will
also be set automatically during Auto
Channel Set.
3
Finish Setting
Press MENU to exit the menu
operations.
Notes:
• If you perform Auto Channel Set when the
aerial cable is not connected properly,
"NO TV SIGNALS" appears on the screen
in step 2. When this happens, make sure of
the aerial connection and press OK/
STATUS; Auto Channel Set will take place
again.
• Depending on reception conditions, the
stations may not be stored in order, and
the station names may not be stored
correctly.

Manual Channel Setting

End
When you want to do channel setting
manually, perform the following
procedures as required.
• If you want to ..........
.......... add channels (See below)
.......... delete unwanted channels
.......... change the channel
.......... perform fine-tuning (See
.......... descramble programmes
.......... change station names (See
• If you live in Eastern Europe, see
ID
INFORMATION on page 18 also.
If you want to add channels
WEST
Access Programmed Channel
1
Information List
1 Press VCR.
2 Press MENU.
3 Press 5 or ∞ to select " MANUAL
TUNER SET UP", then press
OK/STATUS.
(See page 18)
positions (See page 18)
page 18)
when receiving scrambled
broadcasts (See page 18)
page 18)
— 17 —
2
Select Channel Position
1 Press 5∞ 2 3 until a vacant
position in which you want to store a
channel begins blinking.
(Ex.) To store in position 12.
PR CH ID PR CH
01 25 ARD 08 C26 E-SP
02 CDB SKY1 09 55 WEST
03 10 ZDF 10 C24 SAT1
04 C65 RAI1 11 C23 OSF
05 C31 BBC1 12 – – – –
06 C32 BBC2 13 – – – –
07 C33 3SAT 14 – – – –
SELECT: 5 ∞
EDIT : OK
ERASE : CLEAR
END : MENU
The blueback screen and the
programme currently being broadcast
by the selected channel appear
alternately for 8 seconds each.
2 Press OK/STATUS. The Manual
Channel Set screen appears.
3
Set New Channel Information
1 Press 5 or ∞ to change the band
between CH (regular) and CC
(cable), then press 3.
PR CH ID FINE DECODER
01 CC25 ARTE +/– OFF
SELECT : 5 ∞
CURSOR POSITION :
CONFIRM : OK
END : MENU
The blueback screen and the
programme currently being broadcast
by the selected channel appear
alternately for 8 seconds each.
2 Press the Number buttons to input
the channel you want to store.
• Input "0" before any single number
entries.
• To input the registered station name
(ID – P.19), press 3 until "----"
(ID setting) begins blinking, then
press 5 or ∞.
• For fine tuning adjustment, press 3
until "+/–" begins blinking, then
press 5 or ∞. While tuning, "+" or
"–" appears.
• When storing a channel that sends
scrambled broadcasts, press 3 until
"OFF" (Decoder setting) blinks,
then press 5 or ∞ to set
"DECODER" to "ON" ("OFF" is
the default setting).
When "A/V2 SELECT" is set to
"A/V" or "SAT", the "DECODER"
setting cannot be changed ( P.27).
ID