Philips VR1010/75 User Manual page 4

17 SMARTPICTURE button
Selects the SmartPicture mode. ( P.21)
18 Number buttons
(0, 1, 2, 3, 4, 5, 6, 7, 8 and 9)
Before using these buttons, press VCR
or TV to select your target component.
• Press to select a channel on the VCR
or TV.
To select channels 1 to 9, press 0 then
the channel you want. For example, for
channel 4, press 0 then 4.
• Press to enter characters in the
"EDIT TITLE" screen. ( P.15)
• Also used to programme the Timer
Recordings. ( P.25)
19 CLEAR button
• Erases unwanted timer programmes.
( P.25)
• Resets counter to 0:00:00.
20 STILL/SLOW button
• Stops the tape during recording
(pause) or playback (still picture).
( P.13, P.19)
Press again to resume normal
recording.
3
Press PLAY to resume normal
playback.
• Activates slow motion picture when
pressed for more than 2 seconds
during playback. ( P.19)
¢
21 STILL/SLOW + /
• During a slow motion picture, adjusts
the playback speed in the forward
direction. ( P.19)
3
Press PLAY
to resume normal
playback.
• Locates an index marked at the
beginning of every recording. ( P.19)
¡
22 (Fast Forward) /
Before using this button, press VCR or
TV to select your target component.
• After pressing VCR:
– Fast forwards the tape. Also during
playback, starts rapid forward
visual search. ( P.13)
– Changes the setting of a menu item
when using the menus. ( P.10)
• ONLY FOR SOME PHILIPS TVs:
After pressing TV, operates the TV's
menus.
23 OK/STATUS button
Before using this button, press VCR or
TV to select your target component.
• After pressing VCR:
– Goes to the next item on the VCR
menu. ( P.10)
– Displays the time counter, present
vr1010/75
time, channel number, and
remaining tape length. ( P.20)
• After pressing TV:
For some PHILIPS TVs:
– Displays the TV's on-screen
information.
For other manufacturers' TVs:
Functions as the ENTER button if
your TV requires pressing ENTER
after selecting a channel number.
24 CH (channel)
Before using this button, press VCR or
TV.
• After pressing VCR, changes the
channels on the VCR. Release at a
desired channel.
• After pressing TV, changes the
channels on the TV. Release at a
desired channel.
25 TIMER button
Displays the Timer Recording menu.
( P.24)
26 TAPE MANAGER
Press to access the Tape Manager
directory screen. ( P.14)
button
To insert the batteries:
1
Remove the battery compartment lid
from the bottom of the remote
control.
3
button
2
Install two AA batteries —
R6(SUM-3)/AA — matching
polarity indicated inside the battery
compartment.
— 5 —
5
27 SKIP SEARCH button
Press during tape playback to fast
forward 30 seconds of a tape. ( P.19)
28 REC (record)/OTR button
• Start recording when pressed once.
( P.13)
• Starts a recording for 30 minutes to 6
hours long. When pressed more than
5 ∞ once, the shut-off time increases in
30-minute intervals. ( P.20)
/ button
29 Jog Dial
Advances or reverses the picture frame
by frame in the still picture mode.
( P.19)
Note:
The following buttons will glow when you
use or place the remote control in the dark 3
area. 7
• PLAY ¡
• STOP 1
• (Fast forward)
• (Rewind)
• VOL (ume)
• CH (annel)
3
Replace the lid.
Note:
This remote control and batteries are
supplied accessories.
Check to make sure they are included.
Also, check "Specifications" to see what
other accessories are included.
CAUTION
On Battery Replacement
Do not mix old and new batteries.
(Also never mix alkaline batteries
with manganese batteries.)
00.6.29, 4:53 PM
∞
5
∞
5
/
/