Advertisement
5. Select the driver/left Frame Bracket. Slide the Bracket over the end of the frame. Line up the
slots in the sides of the Bracket with the holes in the frame. Select (4) 12mm Bolt Plates. Insert
the Bolt Plates into the open end of the frame and out through the Bracket. Attach the Bracket
to the Bolt Plates with (4) 12mm Flat Washers, (4) 12mm Lock Washers and (4) 12mm Hex
Nuts, (Figures 8 & 9). Leave hardware loose at this time.
6. Attach the mounting tab on the top of the Bracket to the top of the frame with the included (4)
12mm x 50mm Hex Bolts, (8) 12mm Flat Washers, (4) 12mm Lock Washers and (4) 12mm
Hex Nuts, (Figures 10 & 11). Do not fully tighten hardware at this time.
7. Reuse the factory hardware to attach the tow hook to the bottom of the mounting tab on the
Frame Bracket, (Figure 12).
8. Repeat Steps 5—7 to install the passenger/right Frame Bracket and tow hook.
9. With assistance, carefully position the Bumper Assembly up to the Brackets. Temporarily
support the weight of the Bumper. WARNING: To avoid possible injury or damage to the
vehicle, do not proceed until the bumper is fully and safely supported.
10. Line up the (3) holes in the driver/left side of the Bumper with the (3) holes in the Frame
Bracket. Attach the Bumper to the Bracket with the included (3) 12mm x 50mm Hex Bolts, (6)
12mm Flat Washers, (3) 12mm Lock Washers and (3) 12mm Hex Nuts, (Figures 13 & 14). Do
not fully tighten hardware at this time. Repeat to attach the passenger/right side of the Bumper
to the Bracket.
11. Level and adjust the bumper and fully tighten all 12mm hardware to 65-70ft-lbs.
12. Use the included (2) push-in plastic nuts to attach the front license plate, (if required), to the (2)
holes in the front bumper, (Figure 15).
13. Models with factory fog lights:
a. Use a flat blade screwdriver to carefully pop out the tabs on the side of the fog light bracket
attaching the light to the bracket, (Figure 1). Pop the light out of the plastic bracket
housing.
b. Remove the adjustment screw and spring from the light assembly.
c. Select the driver/left top U Bracket, (Figure 16). Attach the Bracket to the slot in the light
opening with the included (1) 8mm Hex Bolt, (2) 8mm Flat Washers and (1) 8mm Nylon
Lock Nut, (Figure 16).
d. Carefully spread the sides of the Bracket enough to slide the OE plastic fog light between
and into the Bracket, (Figure 17). Select (1) Lower U-Bracket. Attach the Lower Bracket to
the Upper Bracket with (2) 6mm Hex Bolts, (2) 6mm Lock Washers and (2) 6mm Flat
Washers, (Figure 18).
e. Insert the factory spring between the tab on the Bracket and the light. Insert the screw
through the tab, spring and into the fog light, (Figure 18).
f. Repeat to install the passenger/right fog light.
14. Reattach the factory wiring harness. Adjust lights as necessary and tighten all fog light bracket
hardware.
15. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing is recommended to add a
protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could
damage the finish. Mild soap may be used to clean the HD Front Bumper assembly.
2017 FORD SUPER DUTY F250-350
Page 2 of 6
ELEVATION FRONT BUMPER
10/2716 (DP)
Advertisement
