Advertisement
Quick Links
48in, 54in, or 60in Recycler
Proline Commercial Walk-Behind Mower with Floating Cutting Unit
Model No. 140-1914
Model No. 140-1915
Model No. 140-1916
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
3
4
5
6
7
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Description
Right baffle
Carriage bolt (5/16 x 3/4 inch)—48-inch
decks only
Carriage bolt (5/16 x 3/4 inch)—54-inch
decks only
Nut (5/16 inch)—48-inch and 60-inch
decks only
Nut (5/16 inch)—54-inch decks only
Discharge chute cover
Bolt (3/8 x 1 inch)—48-inch decks only
Bolt (3/8 x 1 inch)—54-inch and 60-inch
decks only
Nut (3/8 inch)—48-inch and 54-inch
decks only
Nut (3/8 inch)—60-inch decks only
Nut (5/16 inch)—60-in decks only
Bolt (3/8 x 1-1/4 inches)—54-inch decks
only
Bolt (5/16 x 1-1/4 inches)—60-inch
decks only
Kicker baffle
Hex-washer-head bolt (5/16 x 3/4 inch)
Left baffle
Carriage bolt (5/16 x 3/4 inch)—48-inch,
54-inch, and 60-inch decks
Nut (5/16 inch)—48-inch decks only
Nut (5/16 inch)—54-inch and 60-inch
decks only
Decal
Mulching blades
Register at www.Toro.com.
Form No. 3436-332 Rev A
®
Kit
Installation Instructions
Qty.
1
1
2
Install the right baffle.
3
4
1
3
2
3
Install the discharge chute cover.
2
1
1
1
2
Install the kicker baffles (48-inch decks
only).
4
1
1
Install the left baffle.
3
4
1
Install the decal and mulching blades.
3
Original Instructions (EN)
All Rights Reserved *3436-332* A
Printed in the USA
Use
Advertisement
Related Manuals for Toro 140-1914
Summary of Contents for Toro 140-1914
- Page 1 Form No. 3436-332 Rev A 48in, 54in, or 60in Recycler ® Proline Commercial Walk-Behind Mower with Floating Cutting Unit Model No. 140-1914 Model No. 140-1915 Model No. 140-1916 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped.
-
Page 2: Preparing The Machine
Preparing the Machine No Parts Required Procedure Park the machine on a level surface. Disengage the PTO, engage the parking brake. g209902 Shut off the engine and remove the key. Figure 1 For easier access, raise the front of the machine 54-inch deck shown and support it using jack stands rated for your 1. - Page 3 48-Inch Decks 54-Inch Decks Install the right baffle using 2 nuts (5/16 inch) Remove the nuts and bolts from the location as shown in Figure 2. Tighten the fasteners by shown in Figure hand. g308772 Figure 4 1. Nuts and bolts g012805 Figure 2 Install the right baffle using 1 carriage bolt (5/16...
- Page 4 g308757 Figure 6 1. Nut (5/16 inch) 2. Carriage bolt (5/16 x 3/4 inch) Tighten all fasteners. g219326 Figure 8 1. Nut—5/16 inch (3) 3. Welded post (3) 60-Inch Decks 2. Right baffle Remove the nut and bolt from the location shown in Figure 7 Figure...
- Page 5 Procedure 54-inch Decks Install the discharge chute cover using 1 bolt (3/8 x 48-inch Decks 1-1/4 inches), 2 bolts (3/8 x 1 inch) and 3 nuts (3/8 Install the discharge chute cover using 3 bolts (3/8 inch) as shown in Figure x 1 inch) and 3 nuts (3/8 inch) as shown in Figure 9...
- Page 6 Installing the Kicker Baffles Installing the Left Baffle 48-Inch Decks Only Parts needed for this procedure: Left baffle Parts needed for this procedure: Carriage bolt (5/16 x 3/4 inch)—48-inch, 54-inch, and 60-inch decks Kicker baffle Nut (5/16 inch)—48-inch decks only Hex-washer-head bolt (5/16 x 3/4 inch) Nut (5/16 inch)—54-inch and 60-inch decks only Procedure...
- Page 7 g219327 Figure 15 1. Nut (5/16 inch) 3. Left baffle 2. Carriage bolt (5/16 x 3/4 4. Remove the existing g209974 inch) hardware from these holes Figure 16 (54-inch decks only) 1. 30 mm (1.19 inches) 2. 17 mm (0.65 inches) Tighten all fasteners.
-
Page 8: Operation
Cut only about a third of the grass blade. Cutting more genuine Toro replacement blade. than that is not recommended unless grass is sparse, or it is late fall when grass grows more slowly.