[Remote2 Mode] - Panasonic ET-MDNFB10 Operating Instructions Manual

[COMMAND]
[INPUT]
*1 This is displayed when this Interface Board is installed in <SLOT 1>.
*2 This is displayed when this Interface Board is installed in <SLOT 2>.
*3 This is displayed when this Interface Board is installed in <SLOT>.
14) Press the <ENTER> button.
f The command is fixed and n is displayed at the left of the selected command.
f After the command is fixed, press the <MENU> button to close the detailed setting screen.
15) Press asqw to select [STORE], and press the <ENTER> button.
Note
f To delete a command that has been already set, press the <DEFAULT> button on the remote control while the screen in Step 7) is
displayed, or select [DELETE] at the screen in Step 8) and press the <ENTER> button.
f If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
f The operation is performed with the local time set in the projector.
f If an operation is executed with the remote control or control panel of the projector or with a control command before the command set in
[SCHEDULE] is executed, the command set with the schedule function may not be executed.

[REMOTE2 MODE]

Set the <REMOTE 2 IN> terminal.
1) Select [PROJECTOR SETUP] from the main menu.
2) Press the <ENTER> button.
f The [PROJECTOR SETUP] screen is displayed.
3) Press as to select [REMOTE2 MODE].
4) Press qw to switch to [USER].
f The items will switch each time you press the button.
[DEFAULT]
[USER]
5) Press the <ENTER> button.
f The [REMOTE2 MODE] screen is displayed.
6) Press as to select one from [PIN3] to [PIN7], and press qw to switch the setting.
f The items will switch each time you press the button.
[SDI OPT1 [SLOT1]]
[SDI OPT2 [SLOT1]]
[SDI OPT1 [SLOT2]]
[SDI OPT2 [SLOT2]]
[SDI OPT1 [SLOT]]
[SDI OPT2 [SLOT]]
*1 This is displayed when this Interface Board is installed in <SLOT 1>.
*2 This is displayed when this Interface Board is installed in <SLOT 2>.
*3 This is displayed when this Interface Board is installed in <SLOT>.
Menu navigation
Detailed settings of
[COMMAND]
[SDI OPT1 [SLOT1]]
[SDI OPT2 [SLOT1]]
[SDI OPT1 [SLOT2]]
[SDI OPT2 [SLOT2]]
[SDI OPT1 [SLOT]]
[SDI OPT2 [SLOT]]
Uses pin assignment of the <REMOTE 2 IN> terminal in standard setting of the projector.
Changes the setting of the <REMOTE 2 IN> terminal.
Sets the pin to the SDI OPT1 input of the Interface Board.
*1
Sets the pin to the SDI OPT2 input of the Interface Board.
*1
Sets the pin to the SDI OPT1 input of the Interface Board.
*2
Sets the pin to the SDI OPT2 input of the Interface Board.
*2
Sets the pin to the SDI OPT1 input of the Interface Board.
*3
Sets the pin to the SDI OPT2 input of the Interface Board.
*3
Switches the input to SDI OPT1 of the Interface Board.
*1
Switches the input to SDI OPT2 of the Interface Board.
*1
Switches the input to SDI OPT1 of the Interface Board.
*2
Switches the input to SDI OPT2 of the Interface Board.
*2
Switches the input to SDI OPT1 of the Interface Board.
*3
Switches the input to SDI OPT2 of the Interface Board.
*3
Description
ENGLISH - 17