Maintenance - Philips FW880PP/22 Instructions For Use Manual

FW880P-880W/22-Eng 6/15/00
RECORDING
Dubbing tapes
(from tape deck 1 to tape deck 2)
1 Press TAPE to select tape deck 2 .
2 Load the prerecorded tape into tape deck 1 and a
blank tape into tape deck 2.
3 Press SIDE on the remote control to change the
desired direction of the play mode.
™ The FRONT or BACK flag will be displayed,
depending on the side selected.
4 Press REV MODE to select the playback mode ( å å ).
5 Press DUBBING once for normal speed dubbing or
twice for high speed dubbing with in 2 seconds.
™ Both the tapes in deck 1 and 2 will start rewinding
to the front automatically.
™ Dubbing will start immediately after both tapes
have finished rewinding.
™ "NORMAL XXX" (normal speed) or "FAST
XXX" (high speed) will be displayed.
™ The REC flag is displayed.
™ HSD appears on the display for high speed
dubbing.
6 Press STOP Ç to stop dubbing.
Notes:
– " XXX " denotes the counter number.
– Only å å mode is available during recording.
– At the end of side A, flip the tapes to side B and
repeat the procedure.
– Dubbing of tapes is only possible from tape deck 1 to
tape deck 2.
– To ensure good dubbing, use tapes of the same
length.
– During high speed dubbing in Tape mode, the sound is
reduced to a low volume.
4:07 PM Page 25
– You can switch to other sound source while dubbing.
– Dolby NR button has no influence during dubbing
(dubbing from tape deck 1 to tape deck 2). An original
tape recorded with Dolby B NR automatically
produces a copy with Dolby B NR.
CD Synchro Start Recording
During CD synchro start recording,
• It is not advisable to fast forward/rewind your tape in
tape deck 1.
• It is not possible to listen to another source.
1 Press CD.
2 Load a disc into the disc tray.
3 You can program the tracks in the order you want
them to be recorded (see Programming Tracks). If not,
the tracks are recorded according to the selected disc.
4 Press TAPE to select tape deck 2.
5 Load a blank tape (full spool to the left) into tape deck
2.
6 Press SIDE on the remote control to change the
desired direction of the play mode.
™ The FRONT or BACK flag will be displayed,
depending on the side selected.
7 Press REV MODE to select the play mode (å å or ∂
for tape deck 2.
8 Press DOLBY NR to record with Dolby NR.
9 Press CD SYNCHRO to start recording.
™ The REC flag is displayed.
™ After about seven seconds, the CD will start
playing. This is to prevent recording on the leader
tape at the beginning of the tape.
10 Press STOP Ç to stop recording CD playback.

MAINTENANCE

Maintenance
Cleaning the Cabinet
• Use a soft cloth slightly moistened with a mild
detergent solution. Do not use a solution containing
alcohol, spirits, ammonia or abrasives.
Cleaning Discs
• When a disc becomes dirty, clean
it with a cleaning cloth. Wipe the
disc from the center out.
• Do not use solvents such as
benzine, thinner, commercially
available cleaners, or antistatic
spray intended for analog records.
Cleaning the CD lens
After prolonged usage, dirt or dust may accumulate at
the CD lens. To ensure good playback quality, clean the
CD lens with Philips CD Lens Cleaner or any
commercially available. Follow the instructions supplied
with the Lens Cleaner.
Cleaning the Heads and the Tape Paths
• To ensure good recording and playback quality, clean
the heads, the capstan(s), and pressure roller(s) after
every 50 hours of tape operation.
∂ )
• Use a cotton swab slightly moistened with cleaning
fluid or alcohol.
• You can also clean the heads by playing a cleaning
tape through once.
Demagnetizing the heads
• Use a demagnetizing tape available at your dealer.
25