Wear Parts - Lincoln Electric WELDLINE WTT2 20W Instructions For Safety, Use And Maintenance

Trigger simple commands
N°8695-1196_Rev2_05/2018
Simplifi ed maintenance.
1
WTT2 20W
Kit B
WTT2 18W
W000279241
I nstructions for safety, use and maintenance
Ergonomic Range
Kit L
WTT2 4 m 8 m
W000279245
20W EB S W000278891 W000278911
18W EB S W000278895 W000278902
20W
W000278892 W000278909
EB C5B
18W
W000278896 W000278901
EB C5B
20W EB S/
W000382786 W000382787
C5B FLEX
18W EB S/

Wear parts

W000382788 W000382789
C5B FLEX
WTT2 WTT2
REP Ø
20W 18W
Safety instructions
W000306398 W000306399 //
1 W000306400 / //
We thank you for your trust in our company by purchasing this equipment which will provide
you with complete satisfaction if you comply with its conditions for use and maintenance.
W000306402 W000306403 //
2 W000306404 W000306405 //
CAUTION: The company declines all responsibility in case of modifi cation, addition of
3 W000306396 W000306397 //
components or subassemblies, or any transformation of the equipment carried out by
the customer or a thirdparty, without prior specifi c written agreement from the company.
W000306406 W000306411 1.0
W000306407 W000306412 1.6
Arc welding and plasma cutting may be dangerous for the operator and persons close
to the work area. Read the operating manual and safety instructions W000261712.
W000306408 W000306413 2.0
4
See www.weldline.eu.
W000306409 W000306414 2.4
W000306410 W000306415 3.2
A) Maintenance / Troubleshooting
/ W000306416 4.0
Before any internal verifi cations and repair work, make sure that the equipment is separated
W000306376 W000306380 1.0
from the electric installation by electrical isolation (by electrical isolation is meant a group of
operations designed to separate and keep the equipment de-energized). W000306377 W000306381 1.6
At least every six months, you must check the proper condition of the insulation and
W000306378 W000270781 2.0
5
connections of the electric equipment and accessories such as plugs, fl exible wires, ducts,
W000306455 W000306382 2.4
connectors, extension leads, partholders, electrode-holders, or torches...
W000306379 W000306383 3.2
Maintenance and repair work on the jackets and insulating ducts must be carried out
/ W000306384 4.0
extremely carefully.
W000306417 W000306423 6.4
Have defective parts repaired by a specialist, or better still, have them replaced.
W000306418 W000306424 8.0
Routinely check the proper tightening and cleanliness of the electric connections.
W000306419 W000306425 9.6
B) Work-station
6 W000306420 W000306426 11.2
Use only electrode holders and torches which are perfectly insulated.
W000306421 W000306427 12.8
The operator must be insulated from the ground-surface and the workpiece (gloves, safety
W000306422 W000306428 16.0
shoes, dry clothes, leather apron, and so forth...).
/ W000306461 19.2
Do not touch the electrode wire and the part (or the nozzle) simultaneously.
LINCOLN ELECTRIC EUROPE S.L.
LINCOLN ELECTRIC EUROPE S.L.
c/o Balmes, 89 - 8 2 - 08008 Barcelona - SPAIN
o a
c/o Balmes, 89 - 8 2 - 08008 Barcelona - SPAIN
o a
2
EB S
EB C5B
WTT2
Wear parts REP
20W
Short back cap W000306456
Medium back cap W000306457
Long back cap 6L W000306458
Back cap W000306459
Sealing ring /
7 /
W000306385
W000306386
Collet
W000306460
8
W000306387
W000306388
/
W000306429
/
Collet body
W000306431
9
W000306432
W000306433
/
/
9L
Nozzle /
/
4
3
French lever range
WTT2 4 m
20W
W000278893
RL S
18W
W000278897
RL S
20W
W000278894
RL C5B
18W
W000278898
RL C5B
WTT2
Ø Wear parts
18W
/ 4.8
W000306462 6.4
C) Protection
W000306463 8.0 Long Nozzle
It is absolutely essential that your protect your eyes from blinding glare (glare of arc invisible
light and infrared and ultraviolet radiation).
W000306464 9.6
The welding mask, without or with helmet, must always be equipped with a protective fi lter
W000306465 11.2
whose gradation depends on the welding arc current intensity (EN 169 Standard).
W000306466 // Gas Lens sealing ring
Fumes emitted during welding operations may be dangerous. Use adequate protection
W000306389 1.0
means (fumes extraction, ventiled masks...)
W000306390 1.6
/ 2.0
Gas Lens
Technical data
collet body
W000306391 2.4
TIG manual torch with natural cooling
W000306392 3.2
W000306393 4.0
WTT2
W000306434 6.4
Duty cycle 60%
Curent
W000306435 8.0 Duty cycle 100%
Light alloy welding, reduce the duty cycle about 30%
W000306436 9.6
Gas Lens nozzle
Water fl ow mini
W000306437 11.2
Water pressure
W000306438 12.8
Maxi temperature inlet water
W000306438 16.0
Voltage class
W000306467 8.0
Gas fl ow
W000306468 9.6
Long Gas Lens
Using electrodes
nozzle
W000306469 11.2
W000306470 12.8
Back Cap
Origin
equipment fi tted
Nozzle
to the torch
Electrode
Gas connector change
8 m
W000278906
W000278900
RL
W000278905
W000278899
RL
20W
250 A
200 A
7
1.0 l/mn
8
3.3 bars
45°C
L - 113 V
Mini : 7 l/mn - Maxi : 13 l/mn
L
Ø 1.0 / 3.2 mm
9L
9
Long
Long
Ø 12 mm
Ø 2.4 L
www.weldline.eu
www.weldline.eu
EN
EN
EN
S
C5B
1
2
4
3
18W
350 A
5
320 A
L
6L
6
Ø 1.0 / 4.0 mm
Long
Long
Ø 12 mm
Ø 2.4 L