Basic Components (Mixer) - MULTIQUIP Essick Series Operation And Parts Manual

14
13
OFF ON
STOP START
11
12
9
10
15
Figure 3. Mixer Major Components
1.
Safety Grill — Provided for operator safety. This safety
grill is designed to keep hands and solid objects out of the
mixing drum when in use. This grill should be closed at all
times when mixer is in use. DO NOT remove the grill or grill
opening bar. Keep the grill clean by washing it down daily.
2. Dump Handle
— Pull this handle downward to dump the
contents of the drum. Push the handle upward to return the
drum to its vertical position.
3.
Safety Grill Lock Handle — To prevent injury to hands
and arms, the safety grill should ALWAYS be locked when
the mixing of plaster or mortar is required. Also when
transporting the mixer the safety grill should be locked. The
safety grill should only be unlocked when cleaning of the
blades and drum is required.
4.
Pivot Point/Zerk Fitting — There is a zerk grease fitting
on each end of the mixing drum. These fittings lubricate
the dumping mechanism. Lubricate both fittings at least
once a month.
PAGE 16 — EM12M SERIES PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #2 (09/09/19)
1
2
3
4
5
6
7
8
16 17
18
19

BASIC COMPONENTS (MIXER)

5. Drum Bearing — There is a sealed bearing on
each end of the mixing drum. Bearings are packed
and sealed at the factory and require no further
maintenance.
6. Tow Bar/Coupler — This mixer uses various towing
bars, please reference the frame assembly drawing
and parts list in this manual to determine which tow
bar meets your requirements.
7. Safety Chain — This mixer uses a 3/16-inch thick, 72
inches long zinc-plated saftey chain. ALWAYS connect
the safety chain when towing.
8. Chock Blocks (Option) — Place these blocks (not
included as part of the mixer package) under each
mixer wheel to prevent rolling, when mixer is not
connected to the towing vehicle.
9. Cantilever (U-Type) Suspension — This mixer uses
a cantilever type suspension. Check the mounting
hardware for bolt hole elongation and tightness. See
maintenance section of this manual for recommended
maintenance.
10. Tires Ply — The tire ply (layers) number is rated in
letters. This mixer uses 13-inch 2-ply tires. Replace
with only recommended type tires.
11. Cabinet/Latch — Encloses engine and electric motor
(option). NEVER run mixer with cabinet removed. Use
latches to secure engine compartment cabinet.
12. Jack Stand (Option) — Use this jack stand to level
and support the rear end of the mixer during operation.
NEVER deploy on un-level ground and always check
for firmness of ground.
13. Electric Motor ON/OFF Switch — This switch is
located on the inside of the engine cover. When
activated, it will start and stop the electric motor.
14. Engine ON/OFF Switch — This switch is located on
the side of the mixer frame. When activated it will shut
down the engine. Pull out when starting the engine.
15. Mixing Paddles — This mixer uses rubber mixing
paddles for the mixing of plaster and mortar. Always
clean paddles
after each use.
16. Bag Cutter — This feature allows mixing bags to be
opened easily, therefore allowing the contents of the
bag to fall directly into the mixing drum.
17. Engine Cover — Lift this cover to gain access to the
engine or electric motor.
18. Clutch Engagement Lever — Push the clutch lever
forward, toward the tow end of the mixer to engage
clutch. Once the clutch is engaged the paddle shaft
will begin to rotate. To disengage clutch pull the clutch
backwards towards the engine.
19. Mixing Drum — Steel mixing drum. Drum capacity is
12 cu. ft (340 liters). Mixing materials such as mortar,
plaster are to be placed into this drum for mixing.
Always clean the drum after each use. DO NOT use this
mixing drum for the mixing of volatile or hot liquids.