MULTIQUIP Essick Series Operation And Parts Manual
  1. Manuals
  2. Brands
  3. MULTIQUIP Manuals
  4. Mixer
  5. Essick Series
  6. Operation and parts manual
MULTIQUIP Essick Series Operation And Parts Manual

MULTIQUIP Essick Series Operation And Parts Manual

Mechanical drive plaster / mortar mixer
Hide thumbs Also See for Essick Series:
Table of Contents

Advertisement

Quick Links

See also: Operating Manual , Operation and Parts Manual
OPERATION AND PARTS MANUAL
Mechanical Drive
PLASTER/MORTAR MIXER
(HONDA GX390U1QA2 GASOLINE ENGINE)
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
SERIES
MODEL
EM12M
EM12ME51
EM12ME53
Revision #2 (09/09/19)

Advertisement

Table of Contents
loading

Related Manuals for MULTIQUIP Essick Series

Summary of Contents for MULTIQUIP Essick Series

  • Page 1 OPERATION AND PARTS MANUAL SERIES MODEL EM12M EM12ME51 EM12ME53 Mechanical Drive PLASTER/MORTAR MIXER (HONDA GX390U1QA2 GASOLINE ENGINE) Revision #2 (09/09/19) THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
  • Page 2 We sell worldwide for the brands: Genie, Terex, JLG, MultiQuip, Mikasa, Essick, Whiteman, Mayco, Toro Stone, Diamond Products, Generac Magnum, Airman, Haulotte, Barreto,...

  • Page 3: Proposition 65 Warning

    PROPOSITION 65 WARNING PAGE 2 — EM12M SERIES PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #2 (09/09/19)

  • Page 4: Silicosis/Respiratory Warnings

    SILICOSIS/RESPIRATORY WARNINGS WARNING WARNING SILICOSIS WARNING RESPIRATORY HAZARDS Grinding/cutting/drilling of masonry, concrete, metal and Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give other materials can generate dust, mists and fumes off dust or mists containing crystalline silica. Silica is a containing chemicals known to cause serious or fatal basic component of sand, quartz, brick clay, granite and injury or illness, such as respiratory disease, cancer,...

  • Page 5: Table Of Contents

    TABLE OF CONTENTS EM12M Series Mechanical Component Drawings Plaster/Mortar Mixer Nameplate and Decals Assembly ....44–45 Paddle Blades Assembly ......... 46–47 Proposition 65 Warning ........... 2 Drum and Shaft Assembly ....... 48–49 Silicosis/Respiratory Warnings ........ 3 Paddle Shaft Assembly ........50–51 Table of Contents .............
  • Page 6 NOTES EM12M SERIES PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #2 (09/09/19) — PAGE 5...

  • Page 7: Training Checklist

    TRAINING CHECKLIST Training Checklist Description Date Read operation manual completely. Machine layout, location of components, checking of engine oil levels. Fuel system, refueling procedure. Operation of controls (machine not running). Safety controls, safety stop switch operation. Emergency stop procedures. Machine transport and storage. PAGE 6 —...

  • Page 8: Safety Information

    SAFETY INFORMATION Do not operate or service the equipment before reading Potential hazards associated with the operation of this the entire manual. Safety precautions should be followed equipment will be referenced with hazard symbols which at all times when operating this equipment. may appear throughout this manual in conjunction with Failure to read and understand the safety safety messages.
  • Page 9 „ NEVER use accessories or attachments that are not „ Avoid wearing jewelry or loose fi tting clothes that may recommended by Multiquip for this equipment. Damage snag on the controls or moving parts as this can cause to the equipment and/or injury to user may result.
  • Page 10 SAFETY INFORMATION ENGINE SAFETY (GASOLINE MODELS ONLY) MIXER SAFETY DANGER DANGER „ NEVER operate the equipment in an explosive „ Engine fuel exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can atmosphere or near combustible materials. An cause death if inhaled.
  • Page 11 SAFETY INFORMATION GENERATOR SAFETY NOTICE (ELECTRIC MODELS ONLY) „ NEVER run engine without an air fi lter or with a dirty air fi lter. Severe engine damage may occur. Service air fi lter If using a generator to power mixer, refer frequently to prevent engine malfunction.
  • Page 12 SAFETY INFORMATION TOWING SAFETY CAUTION CAUTION „ Ensure that cables and cords will not be tripped over or trapped underneath the mixer. „ Check with your local county or state safety towing regulations, in addition to meeting Department of NOTICE Transportation (DOT) Safety Towing Regulations, „...
  • Page 13 SAFETY INFORMATION ENVIRONMENTAL SAFETY/DECOMMISSIONING EMISSIONS INFORMATION NOTICE NOTICE Decommissioning is a controlled process used to safely The gasoline engine used in this equipment has been retire a piece of equipment that is no longer serviceable. designed to reduce harmful levels of carbon monoxide If the equipment poses an unacceptable and unrepairable (CO), hydrocarbons (HC) and nitrogen oxides (NOx) safety risk due to wear or damage or is no longer cost...

  • Page 14: Mixer Specifications/Noise And Vibration

    MIXER SPECIFICATIONS/NOISE AND VIBRATION Figure 1. Dimensions Table 1. EM12M Series Dimensions/Specifications Reference Letter/Parameter Dimensions in. (mm) A (Height-Grate) 60.8 (1,544) B (Height-Drum Handle) 77.2 (1,961) C (Width-Wheelbase) 54.7 (1,389) D (Length-Jack Stand/Frame) 83.4 (2,118) E (Length-Jack Stand/Tow Bar) 109.7 (2,786) Maximum Mixing Capacity 12 cu.

  • Page 15: Engine/Electric Motor Specifications

    ENGINE/ELECTRIC MOTOR SPECIFICATIONS Table 3. Engine Specifications/Dimensions Model GX390U1QA2 Air cooled 4-stroke OHV petrol engine, 25° inclined Type cylinder, horizontal shaft, cast iron sleeve Bore X Stroke 3.2 in. X 2.5 in. (88 mm x 64 mm) Displacement 389 cm Max.

  • Page 16: General Information

    GENERAL INFORMATION ENGINE MAINTENANCE APPLICATION For basic engine maintenance, refer to the engine This mixer is only intended for the mixing of plaster and mortar. The mixer must be used for its intended purpose maintenance section in this manual. For more detailed and is not suitable for the mixing of flammable or explosive engine maintenance, refer to the Honda Engine Owner's substances.

  • Page 17: Basic Components (Mixer)

    BASIC COMPONENTS (MIXER) 5. Drum Bearing — There is a sealed bearing on each end of the mixing drum. Bearings are packed and sealed at the factory and require no further maintenance. STOP START 6. Tow Bar/Coupler — This mixer uses various towing bars, please reference the frame assembly drawing and parts list in this manual to determine which tow bar meets your requirements.

  • Page 18: Engine Components

    ENGINE COMPONENTS 3. Engine On/Off Switch – ON position permits engine starting, OFF position stops engine operation. 4. Recoil Starter (pull rope) – Manual-starting method. Pull the starter grip until resistance is felt, then pull briskly and smoothly. 5. Fuel Valve Lever – OPEN to let fuel flow, CLOSE to stop the flow of fuel.

  • Page 19: Electric Motor Components

    ELECTRIC MOTOR COMPONENTS ELECTRIC MOTOR ELECTRIC MOTOR POWER CONNECTIONS For lubrication care and operation of the electric motor, The electrical motors used on these mixers are equipped refer to your electric motor instruction booklet furnished with either a 3-prong (1Ø) or a 4-prong (3Ø) plug. with the motor.

  • Page 20: Towing Guidelines

    TOWING GUIDELINES TOWING SAFETY PRECAUTIONS „ ALWAYS make sure that the fuel valve lever is in the OFF position (gasoline models only). CAUTION „ Check wheel mounting lug nuts with a torque wrench. Check with your county or state safety towing Torque wheel lug nuts as described in the maintenance regulations department before towing your mixer.

  • Page 21: Safety Chain Connection

    SAFETY CHAIN CONNECTION 4. Loop (cross) the safety chain (Figure 8) and place CAUTION under the tow bar. Secure the loop with the safety NEVER tow the mixer with the safety chain removed. chain connector link. The safety chain is intended to prevent complete separation of the mixer from the towing vehicle in the event of a tow bar failure.

  • Page 22: Inspection

    INSPECTION Adjust paddles as shown in Figure 10. CENTER ENGINE END CAST PADDLE ENGINE END CAST PADDLE DRUM END CENTER TOW END CAST PADDLE TOW END CAST PADDLE PADDLE BLADE IS TOO TIGHT AGAINST DRUM DRUM SIDE SIDE WALLS CORRECT INCORRECT INCORRECT CORRECT...
  • Page 23 INSPECTION BEFORE STARTING 5. I NOTICE 1. Read all safety instructions at the beginning of manual. Reference engine manufacturer’s manual for specific servicing instructions. 2. Clean the unit, removing dirt and dust, particularly the engine cooling air inlet, carburetor and air cleaner. 3.
  • Page 24 INSPECTION PADDLE BLADE CHECK START/STOP SWITCH (GASOLINE ENGINE) Check for worn or defective paddle blades (Figure 13). 1. Pull the engine start/stop switch (Figure 28) outward Make sure that all blades are adjusted properly. See blade to start the engine adjustment procedure in this manual.

  • Page 25: Start-Up

    START-UP This section is intended to assist the operator with the initial 3. Move the throttle lever (Figure 19) away from the slow start-up of the unit. It is extremely important that position, about 1/3 of the way toward the fast position. this section be read carefully before attempting to use the mixer in the field.

  • Page 26: Start-Up/Operation

    START-UP/OPERATION 6. Pull the starter grip (Figure 22) lightly until you feel 2. To start the electric motor, press the BLACK resistance, then pull briskly. Return the starter grip ON/START switch (Figure 23). gently. PRESS TO START START STOP STARTER GRIP Figure 23.

  • Page 27: Operation

    OPERATION 1. Pull down on the dump handle (Figure 26) to place the drum in dump position. DUMP HANDLE Figure 26. Dump Handle WARNING When rotating the mixing drum from the dump position to the Figure 25. Filling Mixing Drum upright position, keep DUMPING hands clear of safety...
  • Page 28 OPERATION STOPPING THE MIXER (GASOLINE ENGINE) STOPPING THE MIXER (ELECTRIC MOTOR) 1. Place the throttle lever (Figure 27) in the slow (idle) 1. To stop the electric motor, press the RED OFF/STOP position, and let the engine idle 3~5 minutes. switch (Figure 29).

  • Page 29: Maintenance (Engine)

    MAINTENANCE (ENGINE) Use Table 9 as a general maintenance guideline when servicing your engine. For more detail engine maintenance information, refer to the engine owner’s manual supplied with your engine. Table 9. Engine Maintenance Schedule EVERY FIRST EVERY 3 EVERY 6 EVERY 2 DESCRIPTION YEAR...
  • Page 30 MAINTENANCE (ENGINE) MAINTENANCE Spark Plug Perform the scheduled maintenance procedures as defined 1. Remove and clean the spark plug (Figure 31), then by Table 9 and below: adjust the spark gap to 0.024 ~0.028 inch (0.6~0.7 mm). This unit has electronic ignition, which requires DAILY no adjustments.
  • Page 31 We sell worldwide for the brands: Genie, Terex, JLG, MultiQuip, Mikasa, Essick, Whiteman, Mayco, Toro Stone, Diamond Products, Generac Magnum, Airman, Haulotte, Barreto,...
  • Page 32 MAINTENANCE (ENGINE) ENGINE AIR CLEANER SPARK ARRESTER CLEANING 1. Remove the air cleaner cover and foam filter element Clean the spark arrester every 6 months or 100 hours. as shown in Figure 33. 1. Remove the 4 mm screw (3) from the exhaust deflector 2.
  • Page 33 MAINTENANCE (MIXER) DRUM HEAD SEALS DRUM BEARING BRACKET LUBRICATION There is 1 set of drum bearing brackets (Figure 38) that On each end of the mixing drum there is a drum head will require lubrication. These brackets are intended to containing self-adjusting graphite seals.
  • Page 34 If the rotating mixing paddles appear to be losing rotational Figure 40. Clutch Adjustment Lock Location speed, it may be necessary to adjust the clutch. For optimum performance Multiquip recommends 35-55 lbs. NOTICE applied pressure to the hand clutch lever. After the initial...
  • Page 35 MAINTENANCE (MIXER) PADDLE SHAFT BEARINGS b. Using a punch, rotate the adjusting ring one notch at a time in the counter-clockwise direction until a The paddle shafts in this mixer rotate in sealed ball firm 35 to 55 lbs. pressure is felt when engaging bearings, which require no additional lubrication as they the clutch lever (the lever should snap into the are packed and sealed at the factory.
  • Page 36 MAINTENANCE (MIXER) Table 10. Tire Wear Troubleshooting Wear Pattern Cause Solution Adjust pressure to Center Over Infl ation particular load per Wear tire manufacturer Adjust pressure to Edge Under particular load per Wear Infl ation tire manufacturer. Loss of Make sure load does Figure 41.
  • Page 37 MAINTENANCE (MIXER) Lug Nut Torque Requirements Table 11. Tire Torque Requirements First Pass Second Pass Third Pass It is extremely important to apply and maintain proper Wheel Size FT-LBS FT-LBS FT-LBS wheel mounting torque. Be sure to use only the fasteners 12"...

  • Page 38: Troubleshooting (Mixer)

    TROUBLESHOOTING (MIXER) Troubleshooting (Mixer) Symptom Possible Problem Solution Material load too heavy, exceeding Reduce amount of material being mixer capability? mixed. Blades will not rotate. Engine stalls. Improper engine speed? Check and adjust engine speed. Broken connector pin? Replace conncector pin. Paddles will not rotate.

  • Page 39: Troubleshooting (Engine)

    TROUBLESHOOTING (ENGINE) Troubleshooting (Engine) Symptom Possible Problem Solution Spark plug bridging? Check gap, insulation or replace spark plug. Carbon deposit on spark plug? Clean or replace spark plug. Short circuit due to defi cient spark plug Check spark plug insulation, replace if worn. insulation? Improper spark plug gap? Set to proper gap.
  • Page 40 TROUBLESHOOTING (ENGINE) Troubleshooting (Engine) - continued Symptom Possible Problem Solution Air cleaner dirty? Clean or replace air cleaner. Improper level in carburetor? Check fl oat adjustment, rebuild carburetor. Weak in power, compression is proper and does not misfi re. Defective spark plug? Clean or replace spark plug.

  • Page 41: Electric Motor Wiring 1Ø, 230 Vac, 60 Hz

    ELECTRIC MOTOR WIRING 1Ø, 230 VAC, 60 HZ CLOCKWISE ROTATION LOW VOLTAGE (CW) CONFIGURATION MOTOR AMP SETTING CONTROL DETAIL A BLACK WHITE SET TO 22 AMPS WIRE NUTS BLACK 1Ø, 230 VAC 60 Hz. WHITE SWITCH BOX 5HP, 1725 RPM ELECTRIC MOTOR GND.

  • Page 42: Electric Motor Wiring 3Ø, 230 Vac, 60 Hz

    ELECTRIC MOTOR WIRING 3Ø, 230 VAC, 60 HZ CLOCKWISE LOW VOLTAGE ROTATION CONFIGURATION (CW) MOTOR AMP SETTING CONTROL DETAIL A BLACK WHITE SET TO 13 AMPS WIRE NUTS WIRE BLACK 3Ø, 230 VAC, 60 Hz. WHITE SWITCH BOX 5HP, 1725 RPM ELECTRIC MOTOR GND.

  • Page 43: Electric Motor Wiring 3Ø, 460 Vac, 60 Hz

    ELECTRIC MOTOR WIRING 3Ø, 460 VAC, 60 HZ CLOCKWISE HIGH VOLTAGE ROTATION CONFIGURATION (CW) MOTOR AMP SETTING CONTROL DETAIL A BLACK WHITE SET TO 7.5 AMPS WIRE WIRE NUTS BLACK 3Ø, 460 VAC, 60 Hz. WHITE SWITCH BOX 5HP, 1725 RPM ELECTRIC MOTOR GND.

  • Page 44: Explanation Of Code In Remarks Column

    A blank entry generally indicates that the item is not sold assembly/kit that can be purchased, or is not available separately or is not sold by Multiquip. Other entries will for sale through Multiquip. be clarified in the “Remarks” Column.

  • Page 45: Suggested Spare Parts

    SUGGESTED SPARE PARTS EM12 SERIES MECHANICAL MIXER HONDA GX390U1QA2 GASOLINE ENGINE 1 to 3 units 1 to 3 units Qty. Description 3....9807955846 ..SPARK PLUG 1....17620Z0T305 ..TANK CAP, CHROME PLATED 6....491010 ....LATCH KIT, CABINET 3....17210ZE3010 ..AIR CLEANER ELEMENT 1....EM200293B ..PADDLE ARM, TOW END 2....17218ZE3000 ..FILTER OUTER 1....EM200294B ..PADDLE ARM CTR.
  • Page 46 1-1/2 inches. INSPECT BEFORE TOWING TIGHTNESS OF WHEEL NUTS CAUTION TIRE PRESSURE ESSICK CONSTRUCTION PRODUCTS. A MULTIQUIP 1. Use manufacturer’s recommended torque values COMPANY DRUM LOCK POSITIONING when tightening wheel lug nuts. SEE OPERATION MANUAL FOR PROPER 2. Use manufacturer’s recommended tire pressure DRUM LOCK POSITIONING values when inating tires.
  • Page 47 NAMEPLATE AND DECALS ASSY. PART NO. PART NAME QTY. REMARKS 948630 DECAL; PUSH TO STOP 510891 DECAL; MQ ESSICK (SMALL) 510883 DECAL; MQ ESSICK (LARGE) 521229 DECAL; WARNING, BODILY INJURY 521232 DECAL; CAUTION INSPECT BEFORE TOW 2 520935 DECAL; SAFETY INSTRUCTIONS 521228 DECAL;...
  • Page 48 PADDLE BLADES ASSY. PAGE 46 — EM12M SERIES PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #2 (09/09/19)
  • Page 49 PADDLE BLADES ASSY. PART NO. PART NAME QTY. REMARKS 492584 NUT, LOCK 1/2" DIA. NC EM200294B PADDLE ARM, CENTER (TOW END) EM200292 INSERT, PADDLE ARM ........8....REPLACES P/N 200292 EM200296B PADDLE ARM, ENGINE END 6109170 WASHER, FLAT 1/2" ..........8....REPLACES P/N 504322 EM200297 U-BOLT ..............4....REPLACES P/N 200297 EM200295B...
  • Page 50 DRUM AND SHAFT ASSY. PAGE 48 — EM12M SERIES PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #2 (09/09/19)
  • Page 51 DRUM AND SHAFT ASSY. PART NO. PART NAME QTY. REMARKS 805919 DRUM AND SHAFT ASSY.........1....INCLUDES ITEMS W/# EM203449 DRUM GRILL EM924015 PIN, COTTER ............2....REPLACES P/N 505070 6109170 WASHER, FLAT 1/2" DIA........3....REPLACES P/N 492600 804915 DRUM 12 CU. FT..........1....DRUM ONLY EM963692 BOLT, 1/2"...
  • Page 52 PADDLE SHAFT ASSY. PAGE 50 — EM12M SERIES PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #2 (09/09/19)
  • Page 53 PADDLE SHAFT ASSY. PART NO. PART NAME QTY. REMARKS 507844 SPRING EM200287 ADJUSTING NUT EM969012 NUT, NYLOC 3/8" ..........8....REPLACES P/N 505066 EM703 SCREW, ALLEN 3/8" .........4....REPLACES P/N 492470 492584 NUT LOCK 1/2" DIA NC EM963102 BOLT, G5 ............6....REPLACES P/N 492393 3249 CAP, DUST 804887...
  • Page 54 FRAME ASSY. PAGE 52 — EM12M SERIES PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #2 (09/09/19)
  • Page 55 FRAME ASSY. PART NO. PART NAME QTY. REMARKS 804917 CHASSIS ASSY. 804903 HANDLE, DRUM LOCK 509000 PIN, COTTER EM14810 SPRING JOLTER 501269 SPACER 516477 WHEEL/TIRE ASSY. EM941277 HUB COMPLETE, 5 LUGS 492534 NUT, CASTLE 3/4" 507444 WASHER, FLAT 3/4" 504708 WASHER, FLAT 3/4"...
  • Page 56 TOW BAR ASSY. NOTE: OPTIONAL TOW BARS PAGE 54 — EM12M SERIES PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #2 (09/09/19)

  • Page 57: Tow Bar Assembly

    TOW BAR ASSY. PART NO. PART NAME QTY. REMARKS 516580 CLEVIS SAFETY HOOK, 1/4" HLC-1 TOW BAR (LOOP) ..........1....CONTACT SALES HPC-1 TOW BAR (1" PIN) ..........1....CONTACT SALES HBC-1 TOW BAR (BALL HITCH 2-IN) ......1....CONTACT SALES 10176 EM124 BOLT EM12M SERIES PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #2 (09/09/19) — PAGE 55...
  • Page 58 CABINET ASSY. PAGE 56 — EM12M SERIES PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #2 (09/09/19)
  • Page 59 CABINET ASSY. PART NO. PART NAME QTY. REMARKS 804913 ENGINE, COVER 492581 NUT, 1/4"-20 NYLON LOCKNUT 492595 WASHER, FLAT 3/16 512881 RIVET ...............12....REPLACES P/N 503723 802751 HANDLE, COVER 513312 BOLT, 1/4" X 1" 491010 RUBBER LATCH KIT ENGINE HOUSING 492397 SCREW, HEX 1/2"...
  • Page 60 ENGINE ASSY. NOTES: REFER TO “TRANS. ASSY.” FOR PART NO. REFER TO “CLUTCH ASSY.” FOR PART NO. PAGE 58 — EM12M SERIES PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #2 (09/09/19)
  • Page 61 ENGINE ASSY. PART NO. PART NAME QTY. REMARKS 521691 ENGINE, HONDA GX390U1QA2 MODIFIED 1 1456 NUT, HEX 3/8" ...........4....REPLACES P/N 492554 0166A WASHER, LOCK 3/8" DIA.........4....REPLACES P/N 492624 3019092 WASHER, FLAT 3/8" 511122 FITTING, ENGINE 492379 SCREW CAP 3/8" 801570 BRONZE PILOT BUSHING 13376...
  • Page 62 1Ø 230 VAC, 60 HZ ELECTRIC MOTOR ASSY. NOTES: REFER TO “TRANSMISSION ASSY.” FOR PART NO. REFER TO “CLUTCH ASSY.” FOR PART NO. PAGE 60 — EM12M SERIES PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #2 (09/09/19)
  • Page 63 1Ø 230 VAC, 60 HZ ELECTRIC MOTOR ASSY. PART NO. PART NAME QTY. REMARKS EM939228 MOTOR, ELECTRIC 5HP, 1PH EM963610 BOLT 3/8" NC X 1-1/4" G5 .........8....REPLACES P/N 492376 3019092 WASHER, FLAT 3/8" .........12....REPLACES P/N 492598 511122 FITTING, ENGINE 0166A WASHER, LOCK 3/8"...
  • Page 64 3Ø 230/460 VAC, 60 HZ ELECTRIC MOTOR ASSY. NOTES: REFER TO “TRANSMISSION ASSY.” FOR PART NO. REFER TO “CLUTCH ASSY.” FOR PART NO. PAGE 62 — EM12M SERIES PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #2 (09/09/19)
  • Page 65 3Ø 230/460 VAC, 60 HZ ELECTRIC MOTOR ASSY. PART NO. PART NAME QTY. REMARKS EM939229 MOTOR, ELEC. 5HP, 3PH EM963610 BOLT 3/8" ............8....REPLACES P/N 492376 3019092 WASHER, FLAT 3/8" .........12....REPLACES P/N 492598 511122 FITTING, ENGINE 0166A WASHER LOCK 3/8" DIA........4....REPLACES P/N 492624 1456 NUT, HEX 3/8"...
  • Page 66 CLUTCH ASSY. PAGE 64 — EM12M SERIES PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #2 (09/09/19)

  • Page 67: Clutch Assembly

    CLUTCH ASSY. PART NO. PART NAME QTY. REMARKS EM934022 CLUTCH ASSEMBLY ........1....INCLUDES ITEMS W/$ 2656 NUT, NYLOC 5/16-24 EM963289 BOLT, 5/16-24 X 1-3/4" HEX EM918009 SPRING, RELEASE EM934041 DRIVEN MEMBER EM934040 LOCK, ADJUSTING BOLT HHCS 1/4-20 X 1/2" EM934042 PRESSURE PLATE EM925013 PIN 3/16 X 1-3/8 EM925016...
  • Page 68 TRANSMISSION ASSY. ENGINE CRANKSHAFT NOTES: REFER TO CLUTCH ASSY. SECTION FOR PART NUMBERS REFER TO HONDA ENG. ASSY. SECTION FOR PART NUMBERS PAGE 66 — EM12M SERIES PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #2 (09/09/19)
  • Page 69 TRANSMISSION ASSY. PART NO. PART NAME QTY. REMARKS EM600000 COMP. TRANSMISSION ASSY......1....INCLUDES ITEMS W/# EM600018 LEVER EM600024 LOCK PLATE EM922356 BREATHER EM927048 KEY, WOODRUFF EM801965 GASKET EM600028 CLUTCH YOKE 511233 BREATHER EM914005 OIL SEAL EM600029 SHIFTER SHAFT EM300999 STUD 0730 HHCS 1/4-20X1 181B...
  • Page 70 EM12M — TRANSMISSION ASSY. (CONT'D.) ENGINE CRANKSHAFT NOTES: REFER TO CLUTCH ASSY. SECTION FOR PART NUMBERS REFER TO HONDA ENG. ASSY. SECTION FOR PART NUMBERS PAGE 68 — EM12M SERIES PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #2 (09/09/19)
  • Page 71 EM12M — TRANSMISSION ASSY. (CONT'D.) PART NO. PART NAME QTY. REMARKS EM600020 INTERNAL GEAR EM600012 TRANSMISSION HOUSING EM600021 GASKET EM926036 SNAP RING EM511064 SQUARE HEAD PLUG 1/2" EM911329 SQUARE PIPE PLUG 3/8" EM600131 OUTPUT DRIVE PINION EM010062 SQUARE KEY 3/8" X 3/8" 5218 HHCS 1/2-13 X 1-1/2 10176...

  • Page 72: Engine Service Parts

    ENGINE SERVICE PARTS PAGE 70 — EM12M SERIES PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #2 (09/09/19)
  • Page 73 ENGINE SERVICE PARTS PART NO. PART NAME QTY. REMARKS 17218ZE3000 FILTER, OUTER 17210ZE3010 AIR CLEANER ELEMENT 17620Z0T305 TANK CAP, CHROME PLATED 17672ZE2W01 FUEL FILTER 28462ZE3W01 ROPE, RECOIL 9807955846 SPARK PLUG, BPR5ES (NGK) EM12M SERIES PLASTER/MORTAR MIXER • OPERATION AND PARTS MANUAL — REV. #2 (09/09/19) — PAGE 71...
  • Page 74 We sell worldwide for the brands: Genie, Terex, JLG, MultiQuip, Mikasa, Essick, Whiteman, Mayco, Toro Stone, Diamond Products, Generac Magnum, Airman, Haulotte, Barreto,...

This manual is also suitable for:

Essick em12me51Essick em12mEssick em12me53

Table of Contents