KVH Industries TracVision R5 Installation Manual
  1. Manuals
  2. Brands
  3. KVH Industries Manuals
  4. Antenna
  5. TracVision R5
  6. Installation manual

KVH Industries TracVision R5 Installation Manual

Hide thumbs Also See for TracVision R5:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual
TracVision
These instructions explain how to install the TracVision R5/R4
satellite TV antenna system on an RV or motor coach. Complete
instructions on how to use the system are provided in the User's
Guide and your selected receiver's user manual.
Step
1.
2.
3.
4a.
4b.
5.
6.
7.
8.
9.
10.
12.
13.
14.
15.
Technical Support
If you need technical assistance, please contact KVH Technical
Support:
North America, South America, Australia:
Phone: +1 401 847-3327
Email: techs@kvh.com
Europe, Middle East, Asia:
Phone: +45 45 160 180
Email: support@kvh.dk
54-0359 Rev. A
R5/R4 Installation Guide
®
See Page
2
TracVision Antenna
3
4
5
6
7
Baseplate
8
9
10
RF2
(Optional -
11
Systems Only)
12
13
14
16
17
18
TV 2
19
Radome
Vehicle
Power
11-16 VDC
RF1
TV 1
1

Advertisement

Table of Contents
loading

Related Manuals for KVH Industries TracVision R5

Summary of Contents for KVH Industries TracVision R5

  • Page 1: Table Of Contents

    TracVision R5/R4 Installation Guide ® These instructions explain how to install the TracVision R5/R4 satellite TV antenna system on an RV or motor coach. Complete instructions on how to use the system are provided in the User’s Guide and your selected receiver’s user manual.
  • Page 2 TracVision R4, R5, R4SL, R5SL, C3 Addendum PLEASE READ! Important Addendum to Your Product Manual This addendum applies to the following TracVision antenna models: R4, R5, R4SL, R5SL, and C3. New Switchplate Design The switchplate provided with your system differs slightly from the version shown in your manual.
  • Page 3 TracVision R5SL/R4SL/R5/R4/C3 Addendum PLEASE READ! Important Addendum to Your Product Manual This addendum applies to the following TracVision antenna models: R4, R5, R4SL, R5SL, and C3. Power Supply and Grounding Kit A 15-volt, 4-amp power supply and grounding kit are now included with your TracVision system.

  • Page 4: Satellite Receiver

    TracVision R5SL/R4SL/R5/R4/C3 Addendum Installing the Grounding Block Follow the steps below to install the grounding block. a. Connect the grounding block in-line with the antenna’s RF cable(s), between the antenna and the receiver(s), as shown in the diagram below. b. Mount the grounding block to a structure inside the vehicle/vessel.

  • Page 5: Inspect Parts And Get Tools

    Inspect Parts and Get Tools 1. Unpack the box and ensure it contains everything shown on the supplied Contents List. Cables for the R5/R4 system are stored beneath the antenna unit during shipping. 2. Carefully examine all of the supplied parts to Always lift the antenna by the ensure nothing was damaged in shipment.

  • Page 6: Plan The Installation

    Plan the Installation Before you begin, consider the following installation guidelines: • Minimize blockage. The antenna needs a clear view of Height of Minimum Distance the sky to receive satellite TV. Using the table as a Obstruction (A) from Antenna (B) guide, mount the antenna a suitable distance away 8"...

  • Page 7: Remove The Shipping Restraints

    Remove the Shipping Restraints 1. At the bottom of the antenna baseplate, cut the two tie-wraps and pull them out of the baseplate tie-wrap holes. You do not need to remove the radome. The tie-wraps secure the antenna mechanism to prevent shipping damage. You do not need to remove the radome in order to remove the shipping restraints.

  • Page 8: Mount The Antenna (Standard)

    Mount the Antenna (Standard) You can mount the antenna with the baseplate connectors facing the rear of the vehicle (standard orientation), or with the baseplate connectors facing the front of the vehicle (alternate orientation). Follow the steps below to mount the antenna in the standard orientation.

  • Page 9: Mount The Antenna (Alternate)

    Mount the Antenna (Alternate) If you wish to mount the antenna with the baseplate connectors facing the front of the vehicle (alternate orientation), you will need to remove the radome, drill drain holes in the antenna baseplate, then seal the existing factory-drilled drain holes. Follow the steps below to mount the antenna in the alternate orientation.

  • Page 10: Cut The Switchplate Mounting Hole

    Cut the Switchplate Mounting Hole 1. Find a dry, flat location inside the vehicle within 27 feet of the antenna to mount the switchplate. The switchplate must be easily accessible to the user. 2. Using the template supplied in Appendix F on A full-scale panel cutout template page 33, cut out the switchplate mounting hole in has been provided for you in...

  • Page 11: Wire The Antenna

    Wire the Antenna " 1. Drill a 3/4 hole in the roof for the cable access hole. Smooth the edges of the hole to prevent chafing of the cable. 2. Connect the antenna data/power cable to the antenna’s center connector and lock in place. Data/Power (to 2nd Receiver) (to Switchplate)

  • Page 12: Seal The Cable Access Hole

    Seal the Cable Access Hole 1. Seal the cable access hole with a liberal amount of silicone sealant, RTV, or equivalent to protect against leakage. 2. Install the clamshell ventilator, supplied in the kitpack, over the cable access hole using three of the supplied #6 screws.

  • Page 13: Wire The Receiver(S)

    Wire the Receiver(s) If you cut the RF cable(s), be sure to use an Augat IT1000 crimp/strip tool (KVH Part # 19-0242) to attach an F-connector. Do not use a screw-on, push-on, or twist-on connector. Low quality connectors will degrade system performance and allow water/rain to penetrate the cable.

  • Page 14: Wire The Switchplate

    Wire the Switchplate The TracVision system requires an 11-16 VDC power input. A quick-tripping circuit breaker should be installed between the switchplate and vehicle power. Circuit overload protection should be rated for 5 amps. If vehicle power fluctuates widely or is noisy, a 12 VDC 5-amp AC/DC power supply should be installed (KVH Part # 19-0402 or equivalent).

  • Page 15: Mount The Switchplate

    Mount the Switchplate 1. Fit the switchplate flush into the switchplate panel cutout that you made earlier. C. Switchplate Cover B. Switchplate A. Panel Cutout 3.82" (97 mm) 2.36" (60 mm) 2.05" (52 mm) Screw Cavities " (4 mm) " (2.5 mm) 3.19"...

  • Page 16: 11A. Install Satellites (Dish 311 Receivers Only)

    Install Satellites (DISH 311 Receivers Only) The following instructions explain how to install satellites for DISH Network service for use with DISH 311 receivers only. DISH Network does not currently support the use of any other receivers for mobile customers. This procedure does not require a PC.

  • Page 17: 11B. Install Satellites

    Install Satellites If your TracVision system is preconfigured to track your desired satellite pair (see sidebar at left), skip to “Test the System” on page 18. To select a different satellite pair, you will need to connect a PC to the antenna and start the KVH Flash Update Wizard.
  • Page 18 Install Satellites ctd. Follow the steps below to select which satellites to track. Enter all Satellite Installation Names commands in the “TracVision Antenna Comms” window. Satellite Install Name 4. Type HALT then press Enter. † North American Satellites ° 5. Select any two satellite names from either the DSS_72 DIRECTV 72.0 North American or European satellite library.

  • Page 19: Find The Skew Angle (Europe Only)

    Find the Skew Angle (Europe Only) To optimize channel reception, you need to set the LNB skew Approximate Latitude/Longitude angle. Refer to your satellite service provider for the proper skew Grid # Latitude Longitude angle for your specific satellite service and geographic location. You can also find the skew angle for satellites in the TracVision 67°N 7°W...

  • Page 20: Set The Skew Angle (Europe Only)

    Set the Skew Angle (Europe Only) 1. Turn off the antenna and remove the appropriate vehicle fuse to disconnect power. Ensure power is removed from both the antenna and the receiver(s) or multiswitch connected to RF1. 2. Remove the eight screws securing the radome. Before servicing the antenna unit, Remove the radome and set it aside in a safe turn off the antenna and disconnect...

  • Page 21: Test The System

    TracVision Switchplate 4. Within a few minutes, a picture should appear on the TV. 5. (TracVision R5 Only) Take a road test and verify that the antenna tracks the satellite while the vehicle is moving. 6. When you have finished testing, shut down the system.

  • Page 22: Educate The Customer

    Educate the Customer Be sure to give the manuals to the customer and explain how to use the product. The customer also needs to know the following: • The receiver must be activated before it can receive satellite TV programming. •...
  • Page 23 Appendix A System Specifications Physical Characteristics 11-16 volts DC @ 2.5 amps Power nominal, 3.5 amps peak 32" (81 cm) wide x 14.8" (38 cm) Dimensions/Weight high, 33 lbs (15 kg) European system: Single output N. American system: Dual output Maintenance Port EIA, RS232 @ 9600 bps,8,N,1 Pointing System...
  • Page 24 TracVision RF Connectors DC Power The TracVision R5/R4 has the capability of switching from one satellite to another when you choose TV channels that are carried by your DC In RHCP...
  • Page 25 Appendix C User-defined Satellites The TracVision R5/R4 satellite library has two vacancies that you may use to program two user-defined satellites, in case you want to install/watch a satellite not already in the KVH satellite library. To install a user satellite, you will need to obtain the...
  • Page 26 Appendix C User-defined Satellites 3. Type the following command (see the Key below) then press Enter. SATCONFIG,USERX,YYY,Z,D,L Key: = 1 or 2 (This represents the first or second user-defined satellite. Your TracVision system allows up to two user-defined satellites.) YYY= longitude (0-180) = E (East) or W (West) = decoding type (1 = DSS-A, 2 = DSS-B, 3 = DVB)
  • Page 27 – horizontal high & horizontal low – right – left The TracVision R5/R4 antenna requires that the fields for all transponder categories be filled in. If the selected satellite does not have information for one or more of the transponder...
  • Page 28 Appendix C User-defined Satellites An Example of Configuring a User-defined Satellite (Europe) The following is an example of configuring the fictional YOURSAT 101 as the USER1 configured satellite. Prior to configuring this satellite or any others, be certain to get the most up-to-date information from one of the sources previously discussed.
  • Page 29 Appendix C User-defined Satellites An Example of Configuring a User-defined Satellite (N. America) The following is an example of configuring the fictional YOURSAT 101 as the USER1 configured satellite. Prior to configuring this satellite or any others, be certain to get the most up-to-date information from one of the sources previously discussed.

  • Page 30: Switchplate

    Appendix D Replaceable Parts The TracVision R5/R4 system has been designed with durability and low maintenance in mind. If you experience an operating problem or otherwise require technical assistance, contact your local KVH-authorized dealer or distributor. If an authorized dealer/distributor is not located nearby, contact KVH Technical Support (see sidebar).
  • Page 31 (tie-wraps) removed during installation must be replaced. The following instructions explain how to repack the TracVision R5/R4 antenna unit for shipping. 1. Remove the four plugs from the forward and rear tie-wrap holes on the bottom of the baseplate.
  • Page 32 Appendix E Reshipping Instructions 3. Gently rotate the rotating plate until the LNB is aligned with the forward mounting plate arrow. Baseplate Rotating Plate Forward Mounting Plate Arrow Reshipping Orientation 4. Thread one tie-wrap through the rear tie-wrap When moving the rotating plate by holes and through the rotating plate, as shown hand, go slowly! Hitting the below.
  • Page 33 7. Place the entire antenna unit into its shipping box using the original packaging material. Secure the box to a pallet to ensure upright transport. The repacking process is complete! The TracVision R5/R4 is now ready for reshipment. If you need to return the antenna, be sure to obtain an RMA number from KVH’s Technical Support...
  • Page 34 Appendix F Switchplate Template 54-0359 Rev. A...

This manual is also suitable for:

Tracvision r4

Table of Contents