Toshiba IK-WR01A Operation Manual
  1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Security Camera
  5. IK-WR01A
  6. Operation manual

Toshiba IK-WR01A Operation Manual

Toshiba network camera operation manual ik-wr01a
Hide thumbs Also See for IK-WR01A:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
NETWORK CAMERA
: IK-WR01A
Model
Operation Manual
To get started, read the separate "Safety Precautions" carefully.
For information on the latest products and peripheral devices, refer to
the following Web page.
Ihttp://www.netcam.toshiba.com
The above URL is subject to change without prior notice. If the URL
changes, refer to the Toshiba website
(http://www.cctv.toshiba.com).
This User's Guide applies to the firmware version R1.01 and later.
WR01-01

Advertisement

Table of Contents
loading

Related Manuals for Toshiba IK-WR01A

Summary of Contents for Toshiba IK-WR01A

  • Page 1 For information on the latest products and peripheral devices, refer to the following Web page. Ihttp://www.netcam.toshiba.com The above URL is subject to change without prior notice. If the URL changes, refer to the Toshiba website (http://www.cctv.toshiba.com). This User’s Guide applies to the firmware version R1.01 and later. WR01-01...

  • Page 2: Important Safety Instructions

    Important Safety Instructions Be sure to read “IMPORTANT SAFEGUARDS” in the separate “Safety Precautions.”...

  • Page 3: Table Of Contents

    INTRODUCTION FEATURES & DESCRIPTION IK-WR01A has the following features: (1) Flush/Surface mount. (2) IP66 Standard for dust and water resistance. (3) Built in vari-focal lens with auto-iris Focal length 3.0~8.0mm. (4) Incorporated 1/3" type CCD image sensor gives high resolution and excellent sensitivity 480 lines horizontal resolution 0.4 lx minimum illumination with tint dome cover...
  • Page 4 INTRODUCTION (Cont.) GViewing ... 34 Viewing Images ... 34 Camera Window Screen ... 35 • Menu that is displayed when right-clicking on the image ... 35 • Adjusting Images on the Camera ... 36 Adding Images ... 38 GViewing Logs ... 39 GAbout Recording Images ...

  • Page 5: Names And Features Of Parts

    Names and Features of Parts Mode Setting Switch BLC (Backlight Compensation Switch) With the switch on, it adjusts the backlight automatically to obtain the best possible image. Sets camera synchronization to line lock with the switch on. Available only with AC24V. Lens Iris ADJ Counterclockwise: The picture becomes darker.
  • Page 6 INTRODUCTION (Cont.) Video Out Jack Connect a video monitor to the video output jack. RJ45 Connector (Option) Ethernet Port Connect a LAN cable to the port. A PoE compatible hub is also supported. AC24V/DC12V Power Plug Terminal Connect an AC24V/DC12V power plug to the terminal.

  • Page 7: Installation/Setup

    Installation/Setup G Connecting to a Video Monitor G Line-Lock Control G Adjusting a Lens G Setting Up the Network Camera Environment G Connecting the Camera and Personal Computer by Network G Using the Camera Search Application “Camera Finder” G Changing Administrator Login ID and Password G Setting up Access Restriction G Configuring the Network...

  • Page 8: Ginstallation

    INSTALLATION Connect the cable of the camera and the cable from the designated power supply with respective connectors. Screws for securing the camera and mounting base to the ceiling or wall are not supplied with the unit. Use appropriate screws. NOTE •...
  • Page 9 Tilt rotation Horizontal rotation Remove three silver transport protection screws. Transport Protection Screws (silver) To obtain a level image, turn the Horizontal Adjustment Ring. Turn the pan lock counterclockwise to loosen it. Adjust the pan direction of the lens. After adjustment, turn pan lock 1 clockwise to tighten it.
  • Page 10 INSTALLATION (Cont.) The lens tilt angle can be adjusted by loosening the tilt lock 2. After adjusting, tighten the tilt lock 2. Adjust the zoom position by loosening the zoom lock lever 3. After adjusting, tighten the zoom lock lever When installing the camera on a wall, manipulate the horizontal adjustment ring 4 to adjust the inclination of the image.

  • Page 11: Installing The Camera Unit

    Installing the Camera Unit I Installation to Wall or Ceiling with Mounting Base (Surface Mount Installation) • When installing the camera unit on the wall, mount it with the drain groove on the downside. Do not block the drain groove. •...

  • Page 12: Installation To Junction Box With Bracket (Flush Mount Installation)

    INSTALLATION (Cont.) I Installation to Junction Box with Bracket (Flush Mount Installation) Screws (not supplied) Screws Mount camera base with three supplied screws B. (Shorter screw(M4x10)) Tighten and lock the screws firmly. Unit: mm (inches) 4 6 m m ( 1 . 8 1 in c h ) Junction Box 8 3 .

  • Page 13: Change Of Dome Cover

    I Change of Dome Cover Dome replacement When the dome cover is damaged or to be replaced with a transparent cover, call your distributor or sales person. Firmly tighten three mounting screws. Take care not to let dirt or foreign object enter between the parts.

  • Page 14: Gconnecting To A Video Monitor

    Since this camera uses 24V AC UL Listed Class 2 power supply or 12V DC power supply, it should be connected to a power supply that allows for at least 5w consumption. Because the IK-WR01A uses a mechanism, a sufficient power supply with adequate current specifications is required.

  • Page 15: About The Power Select Switch

    About the POWER SELECT Switch CAUTION : The IK-WR01A operates with one of the following power source: 12vDC, 24vAC or PoE. Set the power selection switch on the camera to the correct power source before turning the camera on. DO NOT RE-SET THE POWER SELECTION SWITCH WHEN THE UNIT IS ON.

  • Page 16: Gline-Lock Control

    Line-Lock control Matching the vertical synchronization with the power frequency is called the Line-Lock. This function is activated when the LL of Mode Setting Switch is on. When two or more cameras are switched by video switcher for viewing by a monitor TV, the vertical sync.

  • Page 17: Line Lock Phase

    I LINE LOCK PHASE When a video switcher switches two or more cameras, the picture may fluctuate on the video monitor due to the different AC line phase of each camera. In this case, adjust the V PHASE controller to get a stable image. Line Lock V PHASE CONTROL NOTE The camera is synchronized to the power frequency of 60...

  • Page 18: Gadjusting A Lens

    Adjusting a Lens Back Light Compensation By turning on the back light compensation switch, the camera controls the back light automatically to ensure proper exposure in the specified area when using an auto iris lens or fixed iris lens with the “AES” mode. For setting the metering area of back light compensation, refer to page 37.

  • Page 19: Auto White Balance (Awb)

    NOTE When there is a large difference in contrast between the subject and the surrounding (e.g. when the background is extremely bright), the BLC effect may be limited. Auto White Balance (AWB) The camera has an auto white balance capability in the range of 2,500K to 10,000K color temperature of light.

  • Page 20: Requirements For Network Camera Monitoring System

    Setting Up the Network Camera Environment Requirements for Network Camera Monitoring System ° Administrator’s personal computer This manual refers to a personal computer that has been granted all privileges for configuring, operating, monitoring, and other operations as the “administrator’s personal computer.”...

  • Page 21: Connecting The Camera And Personal Computer By Network

    Connecting the Camera and Personal Computer by Network IAbout the IP Address To connect to the network, the administrator needs to set the network camera IP address. There are two options to set the IP address. • Obtaining an IP address automatically from the DHCP server •...

  • Page 22: Structure Of Connection

    Connecting the Camera and Personal Computer by Network (Cont.) Structure of Connection The following are two methods of connecting the network camera: • Use a crossover cable • Connect with a hub or router G Using a crossover cable to establish a connection (example) IP address 192.168.0.30 Crossover cable is not provided with the product.

  • Page 23: Connecting

    Connecting Connect a LAN cable and then turn the power on. Connect the LAN cable (straight) leading to the camera with a powered hub. Alternatively, use a LAN cable (crossover) to connect the camera with the powered personal computer. When connecting a PoE compatible hub/router, power will be provided to the camera through the LAN cable even though the power plug terminal is not connected.

  • Page 24: Gusing The Camera Search Application "Camera Finder

    G Using “Camera Finder” to Search for a Camera From the “Start” menu, point to “Programs” and “TOSHIBA Network Camera”, and then select “Camera Finder.” Start up “Camera Finder” and click “Search” button. All the cameras currently connected to the network appear.

  • Page 25: G Connecting

    Important Toshiba is not responsible for any damages caused by this software. The “Administrator” button in the “Camera Finder” is invalid for the IK-WR01A. When connecting to the IK-WR01A, be sure to click the “User” button. When you log in as Administrator, set up access restrictions (➝ page. 28).

  • Page 26: Gchanging Administrator Login Id And Password

    Changing Administrator Login ID and Password Be sure to change the default login ID and password. You are able to change important information and settings of the camera through the Administrator Login. To have higher security, be sure to change your login ID and the password. Remember this new login ID and password.
  • Page 27 Enter “root” in the Current login ID field and “ikwb” in the Current Password field. Enter a new login ID in the New login ID field and a new password in the New Password field and New Password (Confirm) field. Enter the same password in the New Password field and the New Password (Confirm) field.

  • Page 28: Gsetting Up Access Restriction

    Setting up Access Restriction You can set up the access restriction by requiring the user to enter the user ID and password for the Administrator login or the registered user ID and password. Click “Configuration” on the left side of the “Camera Window”...
  • Page 29 Click the “Set/Change” button. New user ID and password for the User login are stored in the network camera. Check “ON” in the “User authorization required” section. Click the “Set” button. A screen appears, asking you to enter a user name and password. Enter the Administrator login ID and password in the field of user name and password, respectively ➝Click the “OK”...

  • Page 30: Configuring The Network Manually

    Configuring the Network Manually You can change the settings of network connection manually. • Enter an IP address manually if you are not using, or do not want to use the DHCP server. Log in as Administrator. Click “Configuration” on the left side of the “Camera Window”...
  • Page 31 Select “Manually.” The default setting is “Automatically by DHCP.” Fill in “IP Address,” “Subnet Mask,” “Default Gateway,” “DNS1” and “DNS2.” Important If you do not know the subnet mask, consult the provider or network system administration support center. You do not need to enter the default gateway if the network camera will not be accessed from another network.

  • Page 33: Viewing And Operation

    Viewing and Operation G Viewing G Viewing Logs...

  • Page 34: Viewing Images

    Viewing Viewing Images The images in the network camera can be displayed with the Internet browser on the personal computer. Search for the network camera with the “Camera Finder” ¡ Log into the camera. The browser starts up and then the Camera Window screen appears for the network camera.

  • Page 35: Camera Window Screen

    ICamera Window Screen Name of camera (¡ page.57) * Cannot be operated through the User login. IMenu that is displayed when right-clicking on the image Current date and time of camera (¡ page 58) To record images (¡ page.51) To record currently displayed images (¡ page.53) Image on the camera...

  • Page 36: Adjusting Images On The Camera

    Viewing (Cont.) Adjusting Images on the Camera You can set up the image quality and resolution for the images on the camera. To perform the operation, you need to log in as Administrator. When you log in as User, the operation is disabled.
  • Page 37 G Flickerless You can set up the function to reduce the flickering caused by lighting such as fluorescent lights. On: To activate the flicker compensation Off: Not to activate the flicker compensation (Default: Off) G Area (BLC) You can set up the target area for back light compensation (¡ page.18). Selectable settings: 1 to 5 (default: 1) G AE Level The camera adjusts the brightness of the image automatically.

  • Page 38: Adding Images

    Viewing (Cont.) Adding Images You can add and view images on the other camera. Enter the IP address of other camera in the “Watching:” field ¡ Click “Add.” An image on the other camera is added on the Camera Window screen. Up to 9 images can be displayed on the Camera Window screen.

  • Page 39: Viewing Logs

    Viewing Logs You can view a list of logs. To perform the operation, you need to log in as Administrator. When you log in as User, the operation is disabled. Click “View log” on the left side of the Camera Window screen.

  • Page 41: Gabout Recording Images

    Recording G About Recording Images G Recording Images on FTP Server G Recording Images on a Personal Computer...
  • Page 42 About Recording Images Network camera can record images according to your need. Recordable media and its recordable contents are as follows. Recordable Media FTP Server Personal Computer Recordable Contents Data of “Periodic FTP by Schedule” Data of “Motion Detection” Image data recorded by “Image Recording” (JPEG) (➝...

  • Page 43: Recording Images On Ftp Server

    Recording Images on FTP Server By using FTP server, it becomes possible to manage periodic transferring and saving of huge amounts of recorded image data. The recordable images on an FTP server include “Periodic Recording Data by Schedule” or “Recording by FTP by Motion Detection”. Record Settings Click “Configuration”...

  • Page 44: Ftp General Settings

    Recording Images on FTP Server (Cont.) Configure each setting items. I FTP General Settings You can control the settings to connect to an FTP server. GFTP sever: Select either one of them below and enter correct information. Server Name • IP Address •...
  • Page 45 NOTE • When selecting “Periodic”, network camera logs in to FTP server automatically a minute before the scheduled recording starts. When the scheduled recording stops, there may be some unsent image data left in the camera. The camera will not log out from the FTP server until all images have been transferred.

  • Page 46: Periodic Ftp By Schedule

    Recording Images on FTP Server (Cont.) IPeriodic FTP by Schedule You can control the settings to record images for Periodic FTP by Schedule. To run the recording, select “Periodic” in “Connection to FTP Enable” (➝ page. 43). 1) Configure recording schedule Select one of the setting items for each day of a week.
  • Page 47 NOTE • The cycle may shift depending of Resolution (image size) and networking conditions. 4) Enter “File Name” Select one of two patterns, enter characters in the part described as (keyword). File name will be shown like this: e.g. Pattern1: (keyword) yy mm dd HH MM SS 00.JPG Pattern2: LV (keyword) yyyy mm dd HH MM SS ***N.JPG NOTE •...

  • Page 48: Ftp By Motion Detection

    Recording Images on FTP Server (Cont.) IFTP by Motion Detection You can control the settings to record images for FTP by Motion Detection. To configure the motion detection, select “Enable” in or “Motion Detect” in the alarm settings (➝ page. 64) To run the recording, select “Motion Detection”...
  • Page 49 4) Enter “File Name” Enter characters in the part described as (keyword). File name will be shown like this: e.g. MD (keyword) yyyy mm dd HH MM SS ***N--A.JPG NOTE • You cannot use these characters: \ / : ; , ” | ? * < > Followings are the meaning of each part.

  • Page 50: File Transfer Order

    Recording Images on FTP Server (Cont.) File Transfer Order • Basically, files are transferred in recorded order. However, files may not be transferred depending on the conditions of networking or FTP server. (The camera will not backup data.) NOTE • Depending on the conditions of networking and the FTP server, there may be occasions when files will not transfer.

  • Page 51: Grecording Images On A Personal Computer

    Recording Images on a Personal Computer You can record images in the JPEG file or AVI file format on a personal computer. Image Recording Feature Right-click on the image of the “Camera Window” screen. The operating menu appears on the screen. Click “Image Recording.”...
  • Page 52 Recording Images on a Personal Computer (Cont.) Click the “Start” button. The recording operation starts. To stop the recording, right-click on the image ¡ Click “Stop Image Recording” in the displayed operating menu. Mark here to save images as an AVI file. Mark “Auto”...

  • Page 53: Recording Current Image Data As Still Image

    Recording Current Image Data as Still Image Right-click on the image of the “Camera Window” screen. The operating menu appears on the screen. Click “Save Current Picture As.” A screen appears, asking you to specify the destination folder and file name. Specify the destination folder and file name.

  • Page 55: Updating The Firmware

    Setting up G How to Set up G System Settings G User Settings G Admin Settings G Alarm Settings G Network Settings G Mail Settings G FTP Client Settings G DDNS Settings G Updating the Firmware G Saving the Settings on a Personal Computer...

  • Page 56: General Configuration

    How to Set up Only the Administrator is authorized to set up configurations for the network camera. You can select the setup items by clicking “Configuration” on the “Camera Window” screen. General Configuration Click “Configuration” on the left side of the “Camera Window”...
  • Page 57 System Settings You can change a camera name and control time set. Click “Configuration” on the left side of the “Camera Window” screen. • The Configuration menu appears on the left side of the screen. Click “System” on the left side of the screen. •...

  • Page 58: Restoring The Default Settings

    System Settings (Cont.) GSetting up a format to display date/time 1) Select the “Date-Time Displaying Format” from the pull-down menu. • yyyy-mm-dd HH:MM:SS (ex. 2004-9-15 14:23:32) • dd Mmm yyyy HH:MM:SS (ex. 15 Sep 2004 14:23:32) • mm-dd-yyyy HH:MM:SS (ex. 9-15-2004 14:23:32) (default: dd Mmm yyyy HH:MM:SS) 2) Click the “Change”...

  • Page 59: Rebooting The Network Camera

    IRebooting the network camera You can restart the network camera. 1) Click “Reboot IP Camera.” A confirmation message appears, asking whether or not the camera should be rebooted. 2) Click “OK.” IUpdating the Firmware You can update the firmware on the network camera. Click “Firmware update.”...

  • Page 60: User Settings

    User Settings You can set up access rights. Click “Configuration” on the left side of the “Camera Window” screen. • The Configuration menu appears on the left side of the screen. Click “User” on the left side of the screen. •...
  • Page 61 G Storing the user name and password 1) Enter the user name, password and password (confirm) for a new user in the field of “User ID,” “Password” and “Confirm,” respectively in “Add a user or change password.” 2) Click the “Set/Change” button. •...
  • Page 62 Admin Settings You can change the Administrator ID and password. Click “Configuration” on the left side of the “Camera Window” screen. • The Configuration menu appears on the left side of the screen. Click “Admin” on the left side of the screen. •...
  • Page 63 Configure each item. G Changing the Administrator ID and password 1) Enter the current login ID and the current password in “Current Login ID” and “Current Password,” respectively. 2) Enter new login ID, new password and new password (confirm) in “New Login ID,”...

  • Page 64: Alarm Settings

    Alarm Settings You can configure the motion detection. If you set the function of the “Motion Detect” to “Enable”, an alarm will notify you when a change is detected. Click “Configuration” on the left side of the “Camera Window” screen. •...

  • Page 65: Setting The Motion Detection

    Setting the motion detection. G Setting the motion detection 1) Select one of the followings in “Motion Detect:” Enable : To turn motion detection on. Disable : To turn motion detection off. (Default: Disable) 2) Select the “Sensitivity” level from the pull-down menu. High : Generates an alarm upon detection even to the slightest change in brightness.

  • Page 66: Network Settings

    Network Settings You can configure an IP address for network connection. Click “Configuration” on the left side of the “Camera Window” screen. • The Configuration menu appears on the left side of the screen. Click “Network” on the left side of the screen. •...
  • Page 67 G Configuring the HTTP port number 1) Enter the HTTP port number in “HTTP Port Number” (default: 80). • For most applications, select 80 (default: 80). 2) Click the “Change” button. G DNS update to DNS 1/2 Server When you set a domain name (FQDN) for the camera, you can access the camera with the domain name.
  • Page 68 Mail Settings You can configure the camera to send an email up to 10 addresses when any motions are detected. Click “Configuration” on the left side of the “Camera Window” screen. • The Configuration menu appears on the left side of the screen. Click “Mail”...
  • Page 69 “Receiver email address 10.” 6) Click the “Save Settings” button. 7) Enter the mail title in “Subject” (default: TOSHIBA Network Camera). If a check is added to “Camera Name automatically,” the camera name is set automatically as the subject.
  • Page 70 FTP Client Settings You can store images on an FTP server. Click “Configuration” on the left side of the “Camera Window” screen. • The Configuration menu appears on the left side of the screen. Click “FTP client” on the left side of the screen. •...
  • Page 71 DDNS Settings You can utilize the DDNS. Configure the connection for a DDNS server. Click “Configuration” on the left side of the “Camera Window” screen. • The Configuration menu appears on the left side of the screen. Click “DDNS” on the left side of the screen. •...

  • Page 72: Updating The Firmware

    Download the latest firmware. G Create a folder where you want to save the latest firmware. G Access to the following Toshiba Web page on the Internet. URL: http://www.netcam.toshiba.com G Download the latest firmware according to the instructions on the Web page.

  • Page 73: Click "Firmware Update

    Click “Firmware update.” • The Firmware update screen appears on the right side of the display. Click the “Browse” button. • A screen appears, allowing you to select a file. Select the file of the latest firmware you downloaded in the above “Before Starting”...

  • Page 74: Gsaving The Settings On A Personal Computer

    Saving the Settings on a Personal Computer You can save the settings of the network camera on a personal computer. Click “Configuration” on the left side of the “Camera Window” screen. • The Configuration menu appears on the left side of the screen. Click “System”...

  • Page 75: Importing The Settings Saved On A Personal Computer

    Importing the Settings Saved on a Personal Computer Click “Import new configurations” on the System setting screen. • The Import new configuration screen appears on the right side of the display. Click the “Browse” button. • A screen appears, allowing you to select a file. Select the file on settings you saved.

  • Page 77: Gindex (Glossary)

    Others Index (Glossary) Display of Logs Before Calling Service Personnel... Specifications Appearance Diagram...
  • Page 78 Index (Glossary) AC IN ... 6 Accessories ... Safety Precautions3 Adjust the date and time ... 58 Administrator ... 26 AES ... 18 Alarm settings ... 64 Attaching picture to mail ... 69 AVI ... 52 AWB ... 19 Back light compensation (BLC) ... 18 Before calling service personnel ...
  • Page 79 Hub ... 22 Wire gathering device used in10Base-T/ 100Base-TX network. Build up a network by connecting devices around a hub radially. There are various ports, like 8port, 4port. IP address ... 21 Address information for IP protocol. All devices communicate with IP must have IP addresses.
  • Page 80 TCP/IP. Updating firmware ... 72 URL ... 23 (Uniform Resource Locator) Method for assigning the Internet resource. “http://www.toshiba. com/” is the example of when accessing a website on the Internet. VIDEO OUT ... 6 Video output ... 6 Wall bracket ...
  • Page 81 Display of Logs Display System Boot Change Quality Change resolution Change Brightness Change Contrast Change Saturation Change Hue Set Flickerless Change Area(BLC) Camera Name Set Time Type Set Text Color Change Camera Time Set Daylight Saving Upload IPCamera Set User check Add User Delete User Change Admin...
  • Page 82 Display of Logs (Cont.) Display Set DDNS Set Motion Record FTP down:re-connect FTP Client storage path isn't exist FTP binary mode change fail Mail connect Mail connect fail Send e-mail finish NTP connect fail New client FTP fail to write image Description The DDNS setting is configured The recording at the time of motion detection is set...
  • Page 83 Before Calling Service Personnel... Symptom Cause GThe power of the camera There is no IP address of your is not turned on. network camera GLAN cable is not on The Camera Finder’s Network connected. Camera List. GLAN cable is not connected to the PC.
  • Page 84 Before Calling Service Personnel... (Cont.) Symptom GEntering wrong login ID Error message shows up when and password. trying to login. GCapsLock of the PC is GYou forget your login ID and the password. GDefault gateway is not Cannot access to the camera from configured.
  • Page 85 Symptom Cause GLost the power of the Cannot perform settings. camera during the performance. GLAN cable of the camera has been pulled off during the performance. GLAN cable of the PC has been pulled off during the performance. GLost the power of a hub or router during the performance.
  • Page 86 GWhen many users access to the camera at the same time, the renewal speed of the image becomes slow. GMake sure that the camera is installed in right way. Adjust the setting to place the “Toshiba” logo in the right direction.
  • Page 87 Symptom Cause GMonitor color setting of Colors of the images are poor. your PC is set to 16 bit or less. GThe lens cover of the Focus of the images is poor. camera is not clean, or some dusts are on it. GDistance to an object is too close.
  • Page 88 Before Calling Service Personnel... (Cont.) Symptom GFTP recording function is Recorded images are not not set to ON. saved in FTP GIP address of the FTP server. server, ID/ password or transfer directory is not set properly. GCould not keep the communication with the server during file transfer using FTP.
  • Page 89 About PoE Power Supply Function for Supplying Power via a LAN Cable • There are two PoE (Power Over Ethernet) methods: the Spare Pair method (a power supply method that uses the unused wires) and the Signal Pair method (a power supply method that uses the signal wires).
  • Page 90 Designs and specifications may change without prior notice for better improvement. Some screen displays, pictures and illustrations contained herein may slightly differ from the actual images. IK-WR01A AC 24V 10% 60Hz/DC 12V 10%/ PoE 5.5w 1/3 inch CCD image area sensor 4.96mm (0.195inch) horizontal X 6.0mm...
  • Page 91 Appearance Diagram unit : mm (inches) 48.5 (1.91) 110 (4.33) 155 (6.10)
  • Page 92 Appearance Diagram (Cont.) unit : mm (inches) 150 (5.91) 61.5 (2.42) 41 (1.61) 147.5 (5.81)
  • Page 93 I Bracket unit : mm (inches) 120 (4.72) 46 (1.81) 4-M4 φ φ I Mounting Base 85 (3.35) 46 (1.81) 4.4 (0.17) φ 4-M6 Depth=10 φ φ 15(0.59) 40(1.57) 15(0.59) 55(2.17)
  • Page 94 TOSHIBA AMERICA INFORMATION SYSTEMS. INC Security & Network Video Products 9740 Irvine Boulevard, Irvine California 92618-1697 Phone Number: (877)696-3822...

Table of Contents