Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Delta Manuals
  4. Control Unit
  5. 160 T6 Series
  6. Manual

Delta 160 T6 Series Manual

Flushvalve
Hide thumbs Also See for 160 T6 Series:

Advertisement

Quick Links

Download this manual
13
14
10c
10b
15
22
Filter Screen
22
2
5
Slip Joint Nut Installation
For valves manufactured
after October 2014.
PLEASE LEAVE this M&I Sheet with the owner, maintenance plumber, etc as
items relating to ongoing maintenance suggestions and procedures are included.
Electronic
Concealed
Flushvalve
8a
8b
11a
11b
11c
12
16
3
18
17
19
20
160__T6__ __ __A series
Write purchase model number here for future reference
9
10a
23
6
25
24
21
24VAC
1
6 VDC
7
6
26
4
213777, Rev. A

Advertisement

loading

Related Manuals for Delta 160 T6 Series

Summary of Contents for Delta 160 T6 Series

  • Page 1 Electronic 160__T6__ __ __A series Concealed Write purchase model number here for future reference Flushvalve 24VAC 6 VDC Filter Screen Slip Joint Nut Installation For valves manufactured after October 2014. PLEASE LEAVE this M&I Sheet with the owner, maintenance plumber, etc as items relating to ongoing maintenance suggestions and procedures are included.
  • Page 2 Item # Part # Description 060799A Universal TECK washers and O-rings repair kit 061025A Universal TECK parts washers and O-rings repair kit 060704A‫٭‬ Transformer (110 to 24 VAC) for 5 sensor modules 060771A‫٭‬ Transformer (110 to 24 VAC) for 10 sensor modules 061273A ‫٭٭‬...
  • Page 3 Table 1 - Cap/Pin/Diaphragm Confi guration Table Cap/Solenoid & Regulating Screw Assembly Flush Volume Poppet Pin Diaphragm Assembly (includes Cap, Solenoid, Regulating Screw) 061341A 060508A ‫5.0٭٭‬L (0.125 gal) ‫٭‬UR - Fixed 061342A 061324A ‫9.1٭٭‬L (0.5 gal) 060507A 061346A UR - Adjustable 1.9L (0.5 gal) 061343A ‫2.4٭٭‬L (1.1 gal)
  • Page 4 BEFORE THE FIRST FLUSH INSTALL FILTER SCREEN (included): Note: Place filter in stop bore with conical screen facing the water flow. Caution: Do not push filter in too far. Let filter seat against face of flush valve tail. Periodic cleaning of the filter screen with water is recommended depending on local water conditions to remove any dirt or sediment.
  • Page 5 ELECTRONIC FLUSH VALVE INSTALLATION INSTRUCTIONS STEP 1 - ROUGH-IN FLUSH VALVE, FRAME Fig. 1A Cable Bushing OR BOX Knockouts NOTE: Due to excess back pressure of low flow water closets, outlet tubes must be braced to prevent tubes from disconnecting. •...
  • Page 6 Fig. 1D BOF = Bottom Of Frame 356mm (14”) 14” square 14” x 20” 4-1/2” square Square stainless steel plate stainless steel plate stainless steel plate 305mm (12”) Stainless (frame 12” x 12”) (frame 12” x 18”) Square Frame (box 4” x 4”) frame Steel Cover outline...

  • Page 7: Step 3 - Operation Mode

    Check that the connection of the hardwire converter is made to the electronic board within the electronic flush valve housing. For further technical assistance, call Delta Commercial Technical Service at 1-800-387-8277 (Canada) or 1-877-509-2680 (U.S.A.). Start-Up: When the system is first powered, a sequence of red lights that strobe across the sensing lens window will signify that the valve is now in operation mode.

  • Page 8: Step 4 - Making Adjustments

    STEP 4 - MAKING ADJUSTMENTS (Optional: Only required if factory settings are not preferred.) • To move from operation mode into set-up mode: remove the plastic plug located in the rear of the sensor module and press the set-up mode button once. A pencil or small screwdriver may be required. When done, place the plug back in the hole. 4.1 Adjusting Sensing Distances: •...

  • Page 9: Cleaning Instructions

    NOTE: DO NOT USE EXCESSIVE FORCE to close the inlet stop stem. We RECOMMEND that the flushometer be flushed while closing the inlet stop. The noise created by the water flow or the flow into the fixture will stop when the inlet water is shut off. NOTE: Always use DELTA COMMERCIAL GENUINE PARTS to maintain the warranty. EXCESSIVE NOISE: PARTIALLY close the inlet stop.
  • Page 10 Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. CAN ICES-3 (A) / NMB-3(A) 2018 Masco Canada Ltd. © For further technical assistance, call Delta Commercial Technical Service at 1-800-387-8277 (Canada) or 1-877-509-2680 (U.S.A.). www.deltacommercialfaucets.com 213777, Rev. A Page 10...