1. Manuals
  2. Brands
  3. NCR Manuals
  4. Computer Hardware
  5. 7702-K134
  6. Upgrade manual

NCR 7702-K134 Upgrade Manual

Memory upgrade
Hide thumbs
Table of Contents

Advertisement

Quick Links

Kit Instructions
Memory Upgrade
7702-K134/138
Issue C

Advertisement

Table of Contents
loading

Related Manuals for NCR 7702-K134

Summary of Contents for NCR 7702-K134

  • Page 1 Kit Instructions Memory Upgrade 7702-K134/138 Issue C...
  • Page 2 NCR, therefore, reserves the right to change specifications without prior notice. All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances, photographs are of equipment prototypes. Software screen images are representative, and in some cases, may not match a customer’s installed software exactly.

  • Page 3: Table Of Contents

    Table of Contents Memory Upgrade Kit Contents RealPOS XR7 (7702) Installation Procedures RealPOS XR5 (7603) Installation Procedures SelfServ 75 (7705) Kiosk Installation Procedures Turn off the kiosk Removing the EBox cover Installing the Memory Module Installing the EBox cover Cable Connection...
  • Page 4 Revision Record Issue Date Remarks Jun 2014 First Issue Jul 2018 Added installation procedures for SelfServ 75 Kiosk Jul 2019 Updated procedures for 7705 Kiosk...

  • Page 5: Memory Upgrade

    Kiosk. Refer to the terminal sections in this document for installation procedures. Kit Contents Kit number Description 7702-K134 4 GB Memory Module, DDR3, 1600 7702-K138 8 GB Memory Module, DDR3, 1600 Warning: Disconnect the AC power cord before disassembling the Terminal.

  • Page 6: Realpos Xr7 (7702) Installation Procedures

    Memory Upgrade RealPOS XR7 (7702) Installation Procedures Memory configurations containing a single memory module should be installed in the lower socket (Socket 1). Memory can be expanded by installing a second module in the upper socket (Socket 2). 1. Lay the terminal face down on a flat surface. Caution: Always use a soft material (cloth, foam) to protect the display screen when placing the terminal face down.
  • Page 7 Note: After powering up the terminal, re-flash the SPI/BIOS to ensure the latest version is installed and verify that the terminal is fully functional (see the BIOS Updating Procedures chapter in the NCR RealPOS XR7 User Guide (B005-0000-2332). During this operation you will see a prompt for terminal model and serial number information.

  • Page 8: Realpos Xr5 (7603) Installation Procedures

    Memory Upgrade RealPOS XR5 (7603) Installation Procedures 1. Open the Top Cover. 2. Open the latches at the ends of one of the Memory Module Sockets. 3. Align the DIMM in the socket and push it straight down by applying pressure on the ends smoothly with both hands as indicated by the arrows below (Note that the DIMM connector is keyed).

  • Page 9: Selfserv 75 (7705) Kiosk Installation Procedures

    Memory Upgrade SelfServ 75 (7705) Kiosk Installation Procedures Installing the Memory Module to a 7705 kiosk involves the following procedures: 1. Turn off the kiosk. 2. Remove the EBox cover. 3. Install the Memory Module. Turn off the kiosk Before installing the Memory Module, the kiosk must be completely powered down using the procedures indicated in this section.
  • Page 10 Memory Upgrade 5. If a Sidecar is present, push the Sidecar PSU (Orange) switch to the "0" position. 6. If a UPS is present, push the power switch to shut it down. 7. Disconnect the AC Power Cable from the AC power source.

  • Page 11: Removing The Ebox Cover

    Memory Upgrade Removing the EBox cover Caution: Properly hold and support the EBox cover while loosening or tightening the screws that secure the EBox cover to the EBox chassis. ! Important: Though the cables do not need to be disconnected while removing the EBox cover and installing the Memory Module, it is recommended to take a picture of the cable connections to the EBox and of the cable routing.

  • Page 12: Installing The Memory Module

    Memory Upgrade Installing the Memory Module Caution: Hold the memory modules at the sides only. Never hold more than one module at a time. Never bend or twist the modules as this could seriously damage the contacts. Observe anti-static precautions when handling the memory modules. To install a Memory Module, perform the following steps: 1.
  • Page 13 Memory Upgrade 2. Align the notch on the Memory Module to the notch on the socket and push the module straight down by applying pressure on the ends smoothly with both hands. 3. Ensure that the edges of the module engage the socket latches and that the latches are completely closed.

  • Page 14: Installing The Ebox Cover

    Memory Upgrade Installing the EBox cover Caution: Properly hold and support the EBox cover while loosening or tightening the screws that secure the EBox cover to the EBox chassis. 1. Mount the cover on the chassis, inserting the mounting keyholes over the screws. 2.

  • Page 15: Cable Connection

    Memory Upgrade Cable Connection Note: Depending on the Kiosk configuration, not all device cables may be present. EBOX I/O Panel Cable USB 3.0 Ports 19-inch Touchscreen USB Mini Hub (from top Box USB Mini Hub) RS 232 (COM 1) Note Acceptor USB 1 PIN Pads (IPP350, VX805/820) or UX300 MSR USB 2 Barcode Scanner USB 3...

This manual is also suitable for:

7702-k138

Table of Contents