Retrace Settings Page; Linkage Settings Page - Sony MKS-R4020 Operating Instructions Manual

Invert Display Position
When [Both(2-Line Display)] is selected in [Destination Key
Display Mode] to display the source name and destination
name on two lines on a selection button, this sets which
line is displayed in inverted color.
Top: Invert the top line.
Bottom: Invert the bottom line.
Dest Position (Status & Dest Key)
When [Both(2-Line Display)] is selected in [Destination Key
Display Mode] to display the source name and destination
name on two lines on a selection button, this sets which
line displays the destination.
Also, when displaying the source name and destination
name on two lines, this sets which line displays the
destination.
Top: Display the destination on the top line.
Bottom: Display the destination on the bottom line.
Breakaway
Breakaway Display Mode
Top Level: Display the crosspoints of the top level only.
All Level: Display the crosspoints of all levels.
Breakaway Color
Set the color of buttons when a different source is selected
for each level.
Same as Color Settings: Display the color configured using
[Color Settings] in [Display Settings].
1: Displays white.
2: Displays amber.
3: Displays yellow.
4: Displays green.
5: Displays purple.
6: Displays light blue.
7: Displays dark blue.
8: Displays pink.
Alias Priority
Main LCD
Display Priority #1 to #8
Not supported on the MKS-R4020.
Sub LCD
Display Priority
Select the base name or alias name for the connector
names to display on the STATUS button.
BASE: Display the base name.
1 to 8: Display the Alias1 to Alias8 name.
2-Line Display
Display Priority
Select the base name or alias name for the connector
names to display on the selection button for 2-line display.
BASE: Display the base name.
1 to 8: Display the Alias1 to Alias8 name.

Retrace Settings Page

(Not supported on the MKS-E1620.)
Use to configure the function for retracing the crosspoint
status display and to display the source names of sources.
1
Enter data in the [Retrace Settings] table.
2
Press the [+] icon in [Retrace Settings] to open the
[Retrace] dialog.
3
Enter the destination and source combination and
levels to retrace.
4
Press [Apply] to save the settings. To cancel the
registration, press [Cancel].

Linkage Settings Page

(Not supported on the MKS-E1620.)
Use to configure the panel link function to link multiple
remote control panels.
You can combine remote control panels in a group and link
them by setting one panel as the parent panel and the
others as child panels.
Stand Alone
Select to use a remote control panel in standalone mode.
Child
Select to use a remote control panel as a child panel using
the panel link function.
Authorized: Displays the authorization state from the
parent. "" is displayed in green when authorized
("Not authorized" is displayed when not authorized).
Shared: Displays the status of data sharing with the
parent. Displayed in green when data is shared
successfully ("Not shared" is displayed when data is not
shared).
• Parent IP Address 1: Set the IP address of the LAN1 side
on the parent device. "" is displayed in green on the
right when communication is established with the
parent on LAN1.
• Parent IP Address 2: Set the IP address of the LAN2 side
on the parent device. "" is displayed in green on the
right when communication is established with the
parent on LAN2.
Note
Parent IP Address 1 and 2 are settings for a redundancy
configuration. Specify different IP addresses for the same
parent device.
Parent
Select the remote control panel to use as the parent when
using the panel link function. The name, IP address, and
other information of the remote control panels that can be
configured as the parent device are displayed in a list.
Copy Config button
Copy the settings required by the panel link function to a
child selected in the list.
The Salvo Table, Available Src/Dest, and Control Area items
must be copied. Copy these settings to each child device
after configuring them on the parent device.
19