Installation Check Sheet; Specifications - Roland CAMM-1 PRO CM-500 Service Notes

7 Supplement

7-2 INSTALLATION CHECK SHEET

Check Points
Cleaning
Consumables

7-3 SPECIFICATIONS

Specifications
Mechanism ............................................ Media-movement method
Driving method ..................................... Digital control servo motor
Maximum cutting area .......................... [CM-500] 1195 mm (W) x 24998 mm L) (47" x 984-1/2")
Acceptable media widths ...................... [CM-500] Min.90 mm (3-1/2")
7 Width of material that ........................... [CM-500] 0–1270 mm(0"–50")
can be cut off
Acceptable paper widths ....................... [CM-500] Min.90 mm (3-1/2")
Acceptable paper types .......................... High-quality paper
Tools ...................................................... Cutters: Special cutter for CAMM-1 series
Max.cutting speed ................................. During cutting: 850 mm/sec. (in all directions) During tool-up: 1201 mm /sec. (in 45º direction)
Cutting speed ......................................... 10–850 mm/sec. (in increments of 10 mm/sec.)
Blade force ............................................ 20–350 gf (in increments of 10 gf)
Mechanical resolution ........................... 0.0125 mm/step (*0.000492"/step)
Software resolution ............................... 0.025 mm/step (0.000984"/step)
Distance accuracy .................................. Error of less than +/- 0.2% of distance traveled, or 0.1 mm (0.00394"), whichever is grater
Repetition accuracy ............................... 0.1 mm or less (excluding stretching/contraction of the material)
Interface ................................................. Parallel (Centronics compatible), Serial (RS-232C)
Buffer size ............................................. 2 Mbyte
Instruction system ................................. CAMM-GLIII (mode1, mode2)
Switches ................................................ Power switch, Pen force slider
Control switches .................................... MENU, ENTER, TEST, SETUP, PAUSE, SHEET CUT,
LED ....................................................... POWER LED, SETUP LED, PAUSE LED
Display .................................................. Liquid crystal display unit: 16-character by 2 lines
Power consumption ............................... 1.0 A / 117 V
Acoustic noise level .............................. Cutting mode: under 62 dB (A)
Dimensions ............................................ Main unit: [CM-500] 1586 mm (W) x 286 mm (D) x 281 mm (H) (62-1/2" (W) x 11-5/16" (D) x 11-1/8" (H))
Weight ................................................... Main unit: [CM-500] 41 kg (90.4 lb.)
Operating temperature ........................... 5–40ºC (41–104ºF)
Operating Humidity ............................... 35–80% (non-condensing)
Accessories ............................................ [100V Only] • AC cord 100V 3P: 1 • Adapter plug (100V): 1 • MANUAL,USE JP CM-500/400/300: 1
56
It must be recommended to use water or alcohol for cleaning the following parts.
PLATEN, GRIT ROLLERS, PINCH ROLLERS, BLADE HOLDER CAP
Explain the consumables and how to replace them.
1. Blade
2. Cutter Pad (Protection)
[CM-400] 1000 mm (W) x 24998 mm (L) (39" x 984-1/2")
[CM-300] 737 mm (W) x 24998 mm (L) (29" x 984-1/2")
Max.1372 mm (54")
[CM-400] Min.90 mm (3-1/2") Max.1178 mm (46")
[CM-300] Min.50 mm (2") Max.915 mm (36")
(50–540 mm(2"–21"), 582–915 mm(23"–36"))
[CM-400] 0–1067 mm(0"–42")
[CM-300] 0–812 mm(0"–32")
Max.1372 mm (54")
[CM-400] Min.90 mm (3-1/2") Max.1178 mm (46")
[CM-300] Min.50 mm (2") Max.915 mm (36")
(50–540 mm(2"–21"), 582–915 mm(23"–36"))
Pens: Water-based fiber-tipped pens, and Tick water-based fiber-tipped pens (options)
Range for assured repetition accuracy(*)
For material with a width exceeding 610 mm (24"): Length 4,000 mm (157-7/16") (CM-500/400 only)
For material with a width 610 mm (24") or less: Length 8,000 mm (315-15/16")
0.5 A / 220–230 V
Standby mode: under 40 dB (A)
(According to ISO 7779)
[CM-400] 1391 mm (W) x 286 mm (D) x 281 mm (H) (54-13/16" (W) x 11-5/16" (D) x 11-1/8" (H))
[CM-300] 1128 mm (W) x 286 mm (D) x 281 mm (H) (44-7/16" (W) x 11-5/16" (D) x 11-1/8" (H))
With stand: [CM-500] 1586 mm (W) x 756 mm (D) x 1142 mm (H) (62-1/2" (W) x 29-13/16" (D) x 44-15/16" (H))
[CM-400] 1391 mm (W) x 756 mm (D) x 1142 mm (H) (54-13/16" (W) x 29-13/16" (D) x 44-15/16" (H))
[CM-300] 1128 mm (W) x 756 mm (D) x 1142 mm (H) (44-7/16" (W) x 29-13/16" (D) x 44-15/16" (H))
With stand: [CM-500] 67.5 kg (148.8 lb.)
[Others] • Power cord: 1 • Blade holder (XD-CH2): 1 • Blade (ZEC-U5025): 1
• Test-use water based fiber tipped pen: 1 • Test-use sheet: 1 • Test-use application tape: 1
• Tweezers: 1 • Replacement blade for separating knife: 1 • CAMM-1 DRIVER for Windows
• MANUAL,USE EN CM-500/400/300
Reference
: On demand ** Life time (general guide) of the several types
: On demand of blade is mentioned in the user's manual.
, , ,
0.5 A / 230–240 V
[CM-400] 35 kg (77.2 lb.) [CM-300] 27 kg (59.5 lb.)
[CM-400] 60 kg (132.3 lb.) [CM-300] 50 kg (110.2 lb.)
®
95 disk: 1