1. Manuals
  2. Brands
  3. Skoda Manuals
  4. Automobile
  5. Rapid NH 2013
  6. Maintenance, workshop manual

Skoda Rapid NH 2013 Maintenance, Workshop Manual

Hide thumbs Also See for Rapid NH 2013:
Table of Contents

Advertisement

Quick Links

Service
Skoda Rapid - Maintenance, Workshop Manual
Maintenance
Rapid NH 2013 ➤
Rapid NH 2014 ➤
Edition 06.2018
Service Department. Technical Information

Advertisement

Table of Contents
loading

Related Manuals for Skoda Rapid NH 2013

Summary of Contents for Skoda Rapid NH 2013

  • Page 1 Service Skoda Rapid - Maintenance, Workshop Manual Maintenance Rapid NH 2013 ➤ Rapid NH 2014 ➤ Edition 06.2018 Service Department. Technical Information...
  • Page 2 Service Maintenance H e a d i n g 1. General points 2. Inspections 3. Engines 4. Gearbox 5. Chassis 6. Electrical System 7. Body 8. Exhaust-emission analysis 9. Miscellaneous Technical information should always be available to the foremen and mechanics, because their careful and constant adherence to the instructions is essential to ensure vehicle road-worthiness and safety.

  • Page 3: Table Of Contents

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Contents General points ............
  • Page 4 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 5.11 Tyre pressure monitoring indicator: calibration ........139 Electrical System .

  • Page 5: General Points

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 General points (SIGG000213; Edition 06.2018) ⇒ “1.1 Vehicle identification number”, page 1 ⇒ “1.2 Type plate”, page 3 ⇒ “1.3 Vehicle data sticker”, page 4 ⇒ “1.4 Storage of ŠKODA new vehicles”, page 4 ⇒...
  • Page 6 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 The vehicle identification number can also be found at the bottom left of the front window corner. 1 - Manufacturer's world code XW8 - Manufacturing plant in Russia XWW - Manufacturing plant in Kazakhstan TMB - other Škoda manufacturing plants...

  • Page 7: Type Plate

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 6 - Internal code 7 - Model year: C - 2012 D - 2013 E - 2014 F - 2015 G - 2016 H - 2017 J - 2018...

  • Page 8: Vehicle Data Sticker

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 The identification plate starting from MY 2016 is located on the bottom of the right B pillar -arrow-. Vehicle data sticker WARNING Only valid for vehicles manufactured up to CW 45/2017 The vehicle data carrier is not available for cars manufactured after CW 45/2017.
  • Page 9 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 “Severe conditions” exist, for instance, if the vehicle is operated continuously under one or several of the conditions stated below: ♦ Towing a trailer or when fitted with a roof rack.

  • Page 10: Determine The Age Of The Vehicle

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Changing the code of the service intervals Note Conditions for recoding of service intervals ⇒ “6.11 Changing the code of the service intervals”, page 157 Determine the age of the vehicle The age of the vehicle can be determined according to the sticker affixed to the window.

  • Page 11: Inspections

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Inspections ⇒ “2.1 Pre-Delivery Inspection -PDI- (Export)”, page 7 ⇒ “2.2 Pre-sales Inspection - domestic (Czech Republic)”, page 9 ⇒ “2.3 Delivery Inspection (Export)”, page 13 ⇒ “2.4 Inspection”, page 17 ⇒...
  • Page 12 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 • Immediately check the newly delivered vehicles for completeness and damage (liquidate the transport damage at the expense of the insurance). For this purpose, compare as-delivered condition of vehicle with order form.

  • Page 13: Pre-Sales Inspection - Domestic (Czech Republic)

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Pre-sales Inspection - domestic (Czech Republic)
  • Page 14 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 • Immediately check the newly delivered vehicles for completeness and damage (liquidate the transport damage at the expense of the insurance). For this purpose, compare as-delivered condition of vehicle with order form.
  • Page 15 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Check the tyre pressure (including spare wheel or emergency wheel ), if ⇒ “5.7 Tyres: check”, page 127 necessary correct the tyre pressure to partial load, fit valve caps –...
  • Page 16 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Check vehicle log book for completion, correct language - all in the vehicle log ⇒ “1.8 Checking the vehicle log book”, page 6 book pouch – Attach the “ŠKODA CONNECT” mirror tag to the interior mirror (only for vehicles ⇒...

  • Page 17: Delivery Inspection (Export)

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Delivery Inspection (Export)
  • Page 18 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 • If the vehicles are not transported onwards within two weeks or delivered to the customer, the “care programme for new and used vehicles” must be carried out ⇒...
  • Page 19 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Set the temperature to 22 °C (Climatronic) ⇒ “6.9 Climatronic: set the temperature to 22 °C”, page 147 – Key switch for front passenger airbag deactivation: check “ON/OFF” is working ⇒...
  • Page 20 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Fill out the Owner's Manual, stick a part of the vehicle data sticker without a legend in the Owner's Manual and a part of the vehicle data sticker with the legend on the luggage compartment floor in the vehicle next to the spare wheel.

  • Page 21: Inspection

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Inspection ⇒ “2.4.1 Inspection”, page 17 ⇒ “2.4.2 Extended scope of inspection”, page 19 ⇒ “2.4.3 Additional work up to MY 2016”, page 21 ⇒ “2.4.4 Additional work from MY 2017”, page 24 2.4.1...
  • Page 22 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Deadline for completion ⇒ “2.7 service intervals”, page 37 Work involved Chapter – Check that Škoda Connect services work, enable workshop mode - vehicles with PR ⇒ “6.21 Škoda Connect services”, page 167 number EL2 and EL5 –...
  • Page 23 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 2.4.2 Extended scope of inspection...
  • Page 24 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Deadline for completion ⇒ “2.7 service intervals”, page 37 Work involved Chapter – Interior lights: check ⇒ “6.3 Interior lights: check”, page 142 – Check for corrosion ⇒...
  • Page 25 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 2.4.3 Additional work up to MY 2016...
  • Page 26 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 According to the time and kilometre schedule Chapter After service interval display ⇒ “2.7 service intervals”, page 37 – Engine oil and filter: change engine oil and replace filter ⇒...
  • Page 27 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 According to the time and kilometre schedule Chapter At 180,000 km, then every 30,000 km ⇒ “3.18 Checking particle filter”, page 105 – Check diesel particle filter - common rail diesel engines with diesel particle filter...
  • Page 28 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 2.4.4 Additional work from MY 2017...
  • Page 29 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Work involved Maturity according to time or kilometer date Chapter – Change brake fluid After 3 years, then every 2 years Every 2 years ⇒ “5.4 Change brake fluid”, page 119...
  • Page 30 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Work involved Maturity according to time or kilometer date Chapter Operation in normal weather and traffic Dust-rich countries conditions (low-dust countries) ⇒ “2.6.3 Dust-rich countries”, page 32 –...
  • Page 31 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Additional work - different intervals in tropical/other countries Work involved Maturity according to time or kilometer date Chapter Tropical countries Other countries ⇒ “2.6.4 Tropical countries”, page 33 –...

  • Page 32: Oil Change Service

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Oil change service Deadline for completing the service internal for engine oil change (including engine oil and oil filter) ⇒ “2.7 service intervals”, page 37...
  • Page 33 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 For each oil change service: ♦ Check the use by date of the first aid kit. ♦ Ask the customer if he wishes a wiper blade change.

  • Page 34: Country Allocation Due To Fuel Quality, Dust Content And Temperature

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Country allocation due to fuel quality, dust content and temperature ⇒ “2.6.1 Country overview for petrol fuels which do not comply with the EN 228 standard”, page 30 ⇒...
  • Page 35 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Democratic Republic of Kuwait Zambia Congo Djibouti Laos Saudi Arabia Dominican Republic Lesotho Senegal Dubai Lebanon Seychelles Ecuador Liberia Sierra Leone El Salvador Libya Singapore Ivory Coast...
  • Page 36 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Democratic Republic of Cuba Philippines United Arab Emirates Congo Djibouti Kuwait Puerto Rico Vietnam Dominican Republic Laos Republic of Congo Western Sahara Dubai Lesotho Rwanda Central African Republic...
  • Page 37 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Egypt Liberia Tajikistan Ecuador Macau Tanzania El Salvador Madagascar Thailand Ivory Coast Malawi Togo Eritrea Mali Tunisia Fren. Guyana Morocco Turkey Fiji Mauretania Turkmenistan Philippines Mauritius Uganda...
  • Page 38 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 India Senegal Indonesia Sudan Iraq Zambia Israel South Sudan Yemen Sierra Leone Jordan Somalia Kuwait Swaziland Cameroon Syria Kenya Thailand 2.6.5 Countries with shortened spark plug in‐...
  • Page 39 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Country 30 000 km/2 years 20 000 km/2 years 15 000 km/year 10 000 km/year China Costa Rica Democratic Republic of Congo Djibouti Dominican Republic Dubai Ecuador...
  • Page 40 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Country 30 000 km/2 years 20 000 km/2 years 15 000 km/year 10 000 km/year Macau Madagascar Malawi Malaysia Mali Morocco Mauretania Mauritius Mexico Mongolia Mozambique Myanmar (Burma) Namibia Nepal (Indian sub‐...

  • Page 41: Service Intervals

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Country 30 000 km/2 years 20 000 km/2 years 15 000 km/year 10 000 km/year Swaziland Tajikistan Taiwan Tanzania Thailand Togo Trinidad and Tobago Chad Tunisia Turkey...
  • Page 42 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Service intervals - events: Service-event Deadline for completion Inspection According to the display- after 2 years or 30,000 km and then every 1 year/30,000 km Extended scope of inspection - only in conjunction with inspection First one after 3 years or 60,000 km, then every 2 years/60,000 km...
  • Page 43 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 2.7.2 Service intervals from MY 2017...
  • Page 44 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Inspection Service-event Maturity during operation with fuels according to Maturity during operation with fuels »not according to« of standard EN 228 or EN 590 in normal weather and...
  • Page 45 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Service-event Maturity during operation with fuels according to standard EN Maturity during operation with fuels »not according to« of the EN 228 228 or EN 590 in normal weather and traffic conditions standard ⇒...

  • Page 46: Service Tables With Variations For The Individual Markets Up To My 2016

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Service tables with variations for the in‐ dividual markets up to MY 2016 ⇒ “2.8.1 Market area - Russia”, page 42 ⇒ “2.8.2 Market region - Australia”, page 44 2.8.1...
  • Page 47 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 service intervals Of-to Service-event Interval Since operation Inspection with engine oil change Every 15,000 km or 1 year Extended scope of inspection Every 30,000 km or 2 years 3) Depending on what occurs first.
  • Page 48 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 2.8.2 Market region - Australia Note Valid up to MY 2015. ♦ The tables include only deviating intervals. ♦...
  • Page 49 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Work involved Interval Description of work Air filter: replace Every 45 000 km ⇒ “3.15 Replace air filter element”, page 93 5) Depending on what occurs first.

  • Page 50: Engines

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Engines ⇒ “3.1 Engine overview”, page 46 ⇒ “3.2 Engine fitted”, page 52 ⇒ “3.3 Visual inspection of engine and parts in the engine com‐ partment for leaks and damage”, page 54 ⇒...
  • Page 51 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Petrol engines Engine codes CBZA CBZB CAXA CGPC Emission standard EU-5 EU-5 Manufacturing (from...through) 09.12…05.15 07.12…05.15 10.12 ...05.15 10.12 ...05.15 Displacement in litres Output (kW at rpm)
  • Page 52 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Engine codes CFNA CJZC CJZD CWVA Bore (∅ mm) 76.5 76.5 Stroke (mm) 86.9 75.6 75.6 86.9 Compression ratio 10.5 10.5 10.5 10.5 Hydraulic valve clearance compensation...
  • Page 53 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Engine codes CWVB CZCA CHZB CHZC Catalytic converter Turbocharging Charge air cooler Lambda probe Number of cylinders / valves per cylinder 8) Unleaded petrol 91 RON may also be used for engines for which unleaded petrol 95 RON is specified, although engine power output will be slightly reduced.
  • Page 54 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Diesel engines Engine codes CAYC CLNA CAYB Emission standard Manufacturing (from...through) 07.12…05.15 02.13…05.15 08.13…05.15 Displacement in litres Output (kW at rpm) 77/4400 77/4400 66/4200 Max. torque (Nm at rpm) 250/1500 - 2500 250/1500 - 2500 230/1500 - 2500 Bore (∅...
  • Page 55 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Engine codes CUSB CXMA Output (kW at rpm) 66/3500 85/3500 Max. torque (Nm at rpm) 230/1750 - 2500 250/1500 - 3000 Bore (∅ mm) 79.5 79.5 Stroke (mm) 95.5...

  • Page 56: Engine Fitted

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Engine fitted The Engine codes and serial number are located in the front at the engine/gearbox joint. In addition, a sticker with the Engine codes and serial number is affixed to the timing belt guard.
  • Page 57 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Engine with identification characters CFNA Engine with identification characters CLSA Engine with identification characters CJZC, CJZD, CZCA, CWVA, CWVB, CHZB, CHZC. The engine identification characters are on the crankcase next to the gearbox -arrow-.

  • Page 58: Visual Inspection Of Engine And Parts In The Engine Compartment For Leaks And Damage

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Engine with identification characters CUSB, CXMA. The engine code and engine number are located on the separating layer be‐ tween the engine and the transmission. In addition, a sticker with the “engine identification characters”...

  • Page 59: Replace Engine Oil Filter

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 ♦ for fuel system, ♦ for cooling and heating system ♦ for oil system ♦ for air conditioning system ♦ for suction and air system ♦ for exhaust system ♦...
  • Page 60 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Vehicles with replacement oil filter element Remove replacement oil filter element – Unscrew the screw cap for the oil filter into the height of the lug -a- -arrow- (or by around 3 revolutions if the lug is no longer present) and allow it to remain in this position for a few minutes so that the oil can flow out of the oil filter element.

  • Page 61: Replacing Engine Oil Filter For Diesel Engines Up To My 2015

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 3.4.2 Replacing engine oil filter for petrol en‐ gines starting from MY 2016 Special tools and workshop equipment required ♦ Old oil collection and suction device, e.g. - VAS 6622- ♦...

  • Page 62: Replacing Engine Oil Filter For Diesel Engines Starting From My 2016

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Unscrew the screw cap for the oil filter -1-. – Remove oil filter element -3-. – Clean the sealing surface on the screw cap for the oil filter and on the oil filter housing.

  • Page 63: Replacing Toothed Belt For Camshaft Drive And Tensioning Pulley

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Replacing toothed belt for camshaft drive and tensioning pulley – Removing and Installing toothed belt Engine ⇒ Engine; Rep. gr. 15 . Replacing the V-ribbed belt Removing and installing V-ribbed belt ⇒ Engine; Rep. gr. 13 .
  • Page 64 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Check timing belt for: ♦ Tears or splits -A-, cross-sectional fractures ♦ Lateral catches -B- ♦ Fraying or chunking -C- ♦ Crack in the base tooth -D- ♦...
  • Page 65 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Disconnect plug connection -1-. – Unlock catches -arrows-, remove air guide pipe. – Press release buttons on the hose -1- to remove the activated charcoal filter.

  • Page 66: Inspecting Engine Oil Level

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Check timing belt for: ♦ Tears or splits -A-, cross-sectional fractures ♦ Lateral catches -B- ♦ Fraying or chunking -C- ♦ Crack in the base tooth -D- ♦...

  • Page 67: Drain Off Engine Oil And Top Up

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Dipstick starting from MY 2016 A - The oil must not be topped up. B - Oil can be topped up to the -A- range. C - Oil must be topped up. The oil level must then at least be in the upper part of measuring field -B-.
  • Page 68 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Vehicles with petrol engines with replacement oil filters – Loosen oil filter and unscrew ⇒ “3.4.1 Replacing engine oil filter for petrol engines up to MY 2015”, page 55...
  • Page 69 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Vehicles with petrol engines with replacement oil filter element – Unscrew the screw cap for the oil filter into the height of the lug -a- -arrow- (or by around 3 revolutions if the lug is no longer...
  • Page 70 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 DANGER! Instructions for engines with exhaust gas turbocharger: After the first engine start, change the engine oil and the oil filter and comply with the following: ♦ The engine must only run in idle when the oil pressure warning light is lit in the dash panel insert.
  • Page 71 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Allow the engine oil to drain, catch the oil in a suitable con‐ tainer. Note Observe the disposal instructions! – Locate a new oil seal -2- on a new oil drain plug -3-.
  • Page 72 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Top up with engine oil, specification ⇒ “3.10.5 Oil level, Volkswagen engine oil standards”, page 72 – Reinsert the screw cap. – Start engine and check for leaks.
  • Page 73 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 3.10.3 Vehicles with a diesel engine; draining and topping up with engine oil, up to MY 2015 – Undo the screw cap for the oil filter -1- and keep in this position...
  • Page 74 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Check the engine oil level again and top up with oil if neces‐ sary. – Wait at least 3 minutes after topping up the oil again before inspecting the oil level again.
  • Page 75 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Disconnect the connector -arrow- for the oil level and oil tem‐ perature sender - G266- -1-. – Deposit the connector -arrow- for the oil level and oil temper‐...
  • Page 76 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Tightening torque Oil drain plug – Install a new oil filter ⇒ “3.4.4 Replacing engine oil filter for diesel engines starting from MY 2016”, page 58 – Pour in oil as stated in the specifications ⇒...
  • Page 77 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Engine oil capacities Petrol engines Approximative oil capacity with oil filter change Max. oil capacity after engine repair VW-engine oil standards QI1, QI2, QI3, QI4 1.0 l/70 kW TSI CHZB 4.0 l...
  • Page 78 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Diesel engines Approximative oil capacity with oil filter change Max. oil capacity after engine repair VW-engine oil standards QI1, QI2, QI3, QI4 1.6 l/77 kW TDI CR CAYC 4.3 l...
  • Page 79 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 WARNING On Škoda vehicles, the VW standard for engine oils VW 508 00/509 00 has been introduced for some engines. An engine oil according to VW engine oil standard 508 00/509 00 reduces the CO 2 emissions and can reduce fuel consump‐...

  • Page 80: Cooling System: Check

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Bermuda Cambodia Papua New Guinea Uzbek Bhutan Cameroon Paraguay Venezuela Bolivia Caribbean, left-hand drive Peru United Arab Emirates Botswana Kazakhstan Philippines Vietnam Brunei Kenya Qatar Belarus Burkina Faso...
  • Page 81 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Note When inspecting the antifreeze, read off the exact value on the ♦ light/dark boundary shown on the corresponding scale of the refractometer. Before starting the test, let a drop of water drip onto the meas‐...
  • Page 82 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 The scale -2- of the refractometer - T10007 A- is valid for the coolant additives G13. – Clean the measuring glass of the refractometer after inspect‐ ing the antifreeze.
  • Page 83 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 DANGER! Do not use coolant additives that have not been recommended by ŠKODA AUTO a.s. Current offer on coolant additives ⇒ electronic catalogue of original parts .
  • Page 84 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 The scale -2- of the refractometer - T10007 A- is valid for the coolant additives G13. If the vehicle is filled with the coolant and the antifreeze protection is not adequate, drain part of the coolant from the cooling system.

  • Page 85: V-Ribbed Belt: Check Condition

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 3.11.2 Inspecting coolant level (volume) Inspecting coolant level (volume), up to MY 2015 The coolant expansion reservoir is located on the right of the en‐ gine compartment.

  • Page 86: Routing Of V-Ribbed Belt

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 ♦ Socket Observe the following procedure: – Raise vehicle. – Remove the noise insulation. – Use a socket wrench to crank the engine at vibration damper/ belt pulley -2-.
  • Page 87 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Engine: 1.2 l/55 kW (CGPC) with air-conditioning system 1 - Alternator 2 - Guide pulley 3 - AC compressor 4 - Crankshaft 5 - Tensioning pulley 6 - Coolant pump Engine: 1.4/90 kW (CAXA) with air conditioning unit...
  • Page 88 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Engine: 1.6 l/66 kW TDI CR (CAYB), 1.6 l/77 kW TDI CR (CAYC, CLNA) with air conditioning unit 1 - AC compressor 2 - Crankshaft 3 - Tensioning or guide pulley 4 - Alternator Engine: 1.6 l/77 kW TDI CR (CAYC, CLNA) without air condition‐...

  • Page 89: Replace Spark Plugs

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Engine 1.0 l/70 kW TSI (CHZB), 1.0 l/81 kW TSI (CHZC), 1.2 l/66 kW TSI (CJZC), 1.2 l/81 kW TSI (CJZD), 1.4 l/92 kW TSI (CZCA), 1.4 l/66 kW TDI CR (CUSB), 1.6 l/85 kW TDI CR (CXMA), 1.6l/81 kW MPI (CWVA), 1.6l/66 kW MPI (CWVB) without air conditioning...
  • Page 90 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Engine fitted Change interval Tool for removing the ignition units/plugs 1.2 l/55 kW CGPC Change interval ⇒ “2.4.3 Additional work up to MY 2016”, page 21 -T10118- and -T10094 A- 1.4 l/90 kW...
  • Page 91 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 3.14.1 Replacing spark plugs up to MY 2015 Removing and Installing spark plugs ⇒ Engine; Rep. gr. 28 . 3.14.2 Replace spark plugs - 1.0 l TSI engines –...
  • Page 92 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Coat the ignition coil sealing hoses -arrow- with silicone paste for ignition coil sealing hoses from the ⇒ Electronic Catalogue of Original Parts . – Place all ignition coils loosely into the spark plug shaft.
  • Page 93 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Loosen the hose clamps -1- and -2- and remove the air pipe. – Disconnect plug connections -2-. – Remove screws -1-. – Press extractor -T10530- into the bore of the ignition coil -1- as far as it can go.
  • Page 94 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Coat the ignition coil sealing hoses -arrow- with silicone paste for ignition coil sealing hoses from the ⇒ Electronic Catalogue of Original Parts . – Place all ignition coils loosely into the spark plug shaft.
  • Page 95 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 ♦ Silicone paste for ignition coil sealing hoses ⇒ Electronic Catalogue of Original Parts – Detach hose -2- from air filter housing -1-. – Loosen hose clamp -3- and remove air deflector.
  • Page 96 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Remove ignition coil with extractor -T10530- in -direction of arrow- out of the camshaft housing. – Undo nuts from the extractor -T10530- and remove from the bore of the ignition coil.

  • Page 97: Replace Air Filter Element

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Place air filter housing -1- into the ball pins. – Position hose -2- on the air filter housing -1-. – Position air deflector and secure hose clamp -3-.

  • Page 98: Remove And Install Air Filter Element, 1.0 L Tsi Engines

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 3.15.2 Remove and install air filter element, 1.0 l TSI engines Removing – Release the spring clip -1- and pull air guide hose -2- off. – Unclip vacuum line -1- from the air filter housing and loosen spring clip -2-.
  • Page 99 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Remove air filter housing upwards. – Unscrew the screws -1- from the air filter lower part. – Remove bottom part of the air filter and take out air filter ele‐...

  • Page 100: Replacing Air Filter Element For 1.2 L Tsi And 1.4 L Tsi Petrol Engines Starting From My 2016

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Replace the fastening elements – Remove the fastening elements -1- upwards. – Press the new fastening elements back into the appropriate guides. Note The fastening elements -1- must not be greased or otherwise lu‐...
  • Page 101 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Unscrew the screws -1- from the air filter bottom part. – Carefully release the locking tabs -arrows- on the air filter up‐ per part (risk of breakage).

  • Page 102: Replacing Air Filter Element For 1.6 L Mpi Petrol Engines Starting From My 2016

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 3.15.4 Replacing air filter element for 1.6 l MPI petrol engines starting from MY 2016 Removing – Detach air guide hose -1- from air filter top part.

  • Page 103: Replacing Air Filter Element, 1,4 L Tdi Cr Diesel Engine

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Insert the air filter element -16- in the centre of the air filter bottom part -18-. – Position the air filter top part -8- on the air filter bottom part -18- carefully and without using increased force.
  • Page 104 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Push the coolant pipe out of the air filter housing -5- and de‐ posit on the side. – Disconnect the connector -3- on the air mass meter - G70- .

  • Page 105: Cleaning Air Filter Housing

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Locate the air filter lower part -3- on the air filter upper part -1-. – Bolt together the air filter lower part air and air filter upper part with screws -1-, and tighten to the required tightening torque.

  • Page 106: Replacing The Fuel Filter (Diesel Engines)

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 3.16 Replacing the fuel filter (diesel engines) ⇒ “3.16.1 Replacing the fuel filter (diesel engines), up to MY 2015”, page 102 ⇒ “3.16.2 Replacing the fuel filter (diesel engines), starting from MY 2016”, page 104...
  • Page 107 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Correctly fit locating lug -2- with the guide -arrow- in the area of the retaining lugs -3- at the fuel filter -1-. – Clip retaining ring -2- onto the fuel filter -1-.
  • Page 108 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 3.16.2 Replacing the fuel filter (diesel engines), starting from MY 2016 Special tools and workshop equipment required ♦ Protective gloves ♦ Protective goggles Note Make sure no diesel fuel runs onto the coolant hoses. If nec‐...

  • Page 109: Replace Fuel Filter - Petrol Engines

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Push the fuel filter -1- out of the holder. – Remove the fuel filter -1- from the fuel filter holder in upward direction. Installing – Insert a new filter into the fuel filter holder.
  • Page 110 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Note After replacing the particle filter, carry out“adaption of the engine control unit after replacing particle filter”, i.e. set the limit value for the ash mass to -0-.

  • Page 111: Multipurpose Additive For Petrol Engines

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 3.19 Multipurpose additive for petrol engines ⇒ “3.19.1 Markets in which the multi-purpose additive for petrol engines must be used”, page 107 ⇒ “3.19.2 Recommendation for use of multi-purpose additive for petrol engines”, page 107...
  • Page 112 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Add multi-purpose additive -G 001 770 A2 (90 ml)- or -G 001 780 M3 (200 ml)- for petrol engines in the fuel tank at each service event.

  • Page 113: Multi-Purpose Additive For Diesel Engines

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 3.20 Multi-purpose additive for diesel en‐ gines ⇒ “3.20.1 Markets in which the multi-purpose additive for diesel engines must be used”, page 109 ⇒ “3.20.2 Recommendation for use of multi-purpose additive for diesel fuel”, page 109...
  • Page 114 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Country Egypt Morocco Albania Mauretania Equatorial Guinea Macedonia Argentina Moldova Azerbaijan Myanmar Belize Dutch overseas territories Benin Nigeria Bhutan Pakistan Brazil Panama Brunei Paraguay Burkina Faso Saudi Arabia...

  • Page 115: Gearbox

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Gearbox ⇒ “4.1 Check final drive and joint boots for leaks and damage”, page 111 ⇒ “4.2 6-speed automatic gearbox 09G: check ATF level and quality, refill or replace ATF”, page 111...
  • Page 116 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Note The ATF temperature is read off at the ⇒ Vehicle diagnostic ♦ tester. The ATF level changes with ATF temperature. ♦ Checking ATF level when ATF temperature is too low may re‐...
  • Page 117 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – if an ATF temperature of 35 °C is reached, unscrew the ATF inspection plug -A-. – Always replace gasket ring -arrows- for ATF inspection plug ⇒ Electronic Catalogue of Original Parts .
  • Page 118 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Shorten the vent pipe to the dimension -a-, so that it does not touch the bottom of certain ATF bottles. Cut dimension to length -a-: 210 mm.
  • Page 119 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Screw in the adapter for ATF oil filling - VAS 6262/2- by hand in the location of the gearbox inspection plug -arrow 1- and connect adapter for oil filling - VAS 6262- or -VAS 6262A- .

  • Page 120: Chassis

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Chassis ⇒ “5.1 Inspecting thickness of front and rear brake pads/linings”, page 116 ⇒ “5.2 Clean rear drum brake (noises, glue brake pad)”, page 118 ⇒ “5.3 Inspecting brake system for leaks and damage”, page 118 ⇒...
  • Page 121 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Note When removing the inspection pin, ensure that the grinder ♦ does not move otherwise this can result in an incorrect meas‐ urement. On certain vehicles (e.g. with steel rims), where the inspection ♦...

  • Page 122: Clean Rear Drum Brake (Noises, Glue Brake Pad)

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Remove the rubber plugs -1- from the brake carrier plates -2-. – Inspect the thickness of the brake linings through the inspec‐ tion holes in the brake carrier plates.

  • Page 123: Change Brake Fluid

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Ensure that the brake hoses do not touch any parts of the ve‐ hicle when the steering is turned to full left or full right lock.
  • Page 124 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Extract brake fluid from the brake fluid reservoir. – Switch on the extraction function of the brake filling and bleed‐ ing device , e.g. -VAS 5234- .
  • Page 125 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Use an extraction hose with end part to extract as much brake fluid as possible from the brake fluid reservoir. WARNING Drained (used) brake fluid must never be used again.
  • Page 126 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Screw the thread plug -1- of the brake filling and bleeding de‐ vice , e.g. -VAS 5234- , onto the brake fluid reservoir. 1 - Thread plug...
  • Page 127 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Provide a catch pan for used brake fluid. Note Use the tool set for brake bleeding - VAS 6564- to loosen and ♦ tighten. While doing so, pull the bleeder hose through the socket insert with a corresponding hollow adapter piece from this set.
  • Page 128 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Fit the bleeder hose -A- on the slave cylinder -arrow- and open the bleeder valve. Continued for all vehicles – Open vent valve and allow approx. 0.15 litres of brake fluid to flow out.
  • Page 129 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Fit bleeder hose -1- of catch pan onto the bleeder valve of the rear right wheel. Note Slacken the bleeder valves using the set of tools for brake ♦...

  • Page 130: Brake Fluid Level: Check

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Brake fluid level: check. Only use new original brake fluid N.052.766.Z0 as per US stand‐ ard FMVSS 571.116, DOT 4 and VW standard 501 14 . WARNING ♦...

  • Page 131: Tyres: Check

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Check sealing boots -arrow- of steering joints for leaks, dam‐ age and correct position. – Check the rubber-metal bearings -arrow- of the axles for the following damage: ♦...

  • Page 132: Inspecting Tyre Tread Depth (Including Spare Wheel) And Entering

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Inspection: – Inspect the tyre tread and side wall for damage, if necessary remove any foreign bodies from the tyres, such as nails or glass splinters. – Inspect tyres for scrubbing, tread worn down on one side, po‐...
  • Page 133 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Move the pin -1- with the grinder of the inspection pin -3- in such a way that the measurement pin of the inspection pin -4- rests fully against the inner tread of the tyre.
  • Page 134 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Tyre pressure values Rapid NH Engine Tyres Tyre pressure (kPa/bar) half load full load Front axle Rear axle Front axle Rear axle 1.2 l/55 kW MPI 175/70 R14 210/2.1 220/2.2...
  • Page 135 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Tyre pressure values Rapid NH Green Line Engine Tyres Tyre pressure (kPa/bar) half load half load full load Normal Comfort Front axle Rear axle Front axle Rear axle Front axle Rear axle 1.6 l/66 kW TDI CR 185/60 R15 260/2.6...
  • Page 136 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Engine Tyres Tyre pressure (kPa/bar) half load full load Front axle Rear axle Front axle Rear axle 1.6 l/66 kW TDI CR 220/2.2 220/2.2 240/2.4 310/3.1 1.6 l/77 kW TDI CR 220/2.2...
  • Page 137 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 5.7.4 Check the tyre pressure (including spare wheel) and if necessary correct pressure, up to MY 2016 Special tools and workshop equipment required ♦ Tyre pressure tester e.g. VAS 5216 Caution ♦...
  • Page 138 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Tyre pressure values Rapid NH Engine Tyres Tyre pressure (kPa/bar) half load half payload - eco-mode full load Front axle Rear axle Front axle Rear axle Front axle Rear axle 1.2/66 kW TSI...
  • Page 139 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Engine Tyres Tyre pressure (kPa/bar) half load half payload - eco-mode full load Front axle Rear axle Front axle Rear axle Front axle Rear axle 1.2/81 kW TSI 220/2.2...
  • Page 140 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Engine Tyres Tyre pressure (kPa/bar) half load half payload - eco-mode full load Front axle Rear axle Front axle Rear axle Front axle Rear axle 1.2 l/55 kW MPI 210/2.1...
  • Page 141 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Engine Tyres Tyre pressure (kPa/bar) half load half payload - eco-mode full load Front axle Rear axle Front axle Rear axle Front axle Rear axle 1.6 l/81 kW MPI 220/2.2...

  • Page 142: Tightening Wheel Bolts To Specific Torque

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Tightening wheel bolts to specific torque Tightening torque for steel and light alloy wheel rims: 120 Nm. Transport lock: remove the front axle locking components On vehicles with a basic chassis, blocking components are at‐...

  • Page 143: Tyre Pressure Monitoring Indicator: Calibration

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Note The tyre sealant in the bottle is perishable. ♦ Therefore, the best before date is given on the bottle -arrow-. ♦ – Check the best before date and enter it in the maintenance tables.
  • Page 144 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 • the tyre structure is damaged • the vehicle is loaded on one side • the wheels on an axle are heavily loaded (e.g when operating a trailer, on steep gradients).

  • Page 145: Electrical System

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Electrical System ⇒ “6.1 Electric consumers: check they are functioning”, page 141 ⇒ “6.2 Front and rear exterior lighting: check”, page 142 ⇒ “6.3 Interior lights: check”, page 142 ⇒...

  • Page 146: Front And Rear Exterior Lighting: Check

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Check electric windows, electrically-adjustable exterior mir‐ rors (heated, adjustable), central locking and comfort locking. – Inspect heating of front seats. – Check heated windows. – Inspect radio, navigation system for proper reception and ab‐...
  • Page 147 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Operate the volume control. – Carry out station programming – Inspect station search – Check CD/DVD or SD player (insert CD/DVD or SD and play) Use the latest version of the cartographic data (data) approved by Škoda Auto for the radio navigation system (RNS)

  • Page 148: Setting Clock

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Setting clock ⇒ “6.6.1 Setting clock, up to MY 2015”, page 144 ⇒ “6.6.2 Setting clock, starting from MY 2016”, page 145 6.6.1 Setting clock, up to MY 2015 Vehicles without an information display The clock is set using the operating buttons -1- and -3-.

  • Page 149: Connect Diagnostic Unit

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 6.6.2 Setting clock, starting from MY 2016 Set the clock with the buttons on the instrument cluster Control button -1- is used to set the clock. 0.0/SET –...

  • Page 150: Adapt Language Variants To Driver's Instructions

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Adapt language variants to driver's in‐ structions ⇒ “6.8.1 Selecting language in the dash panel insert, up to MY 2015”, page 146 ⇒ “6.8.2 Adapting language variants to driver's instructions, start‐...

  • Page 151: Climatronic: Set The Temperature To 22 °C

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Set the desired language taking account of the diagnostic unit display. Adjust the language variant for vehicles with infotainment radio/ navigation The adjustment of the language variants for driver's instructions...

  • Page 152: Resetting Service Interval Display (Sid)

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 6.10 Resetting service interval display (SID) ⇒ “6.10.1 Display the remaining kilometres and days until the next inspection service.”, page 148 ⇒ “6.10.2 Reset service interval display in MY 2013”, page 150 ⇒...
  • Page 153 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Press the button -1- 4 times. The remaining kilometres and days until the next inspection serv‐ ice appear in the display -2-. The “Wrench” symbol appears in the display for approx. 10 s and the number of remaining days and number of kilometres until the next inspection service is displayed.
  • Page 154 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Hold the button -2- on the windscreen wiper lever pressed for longer than 1 second. This will show the information display of the »MAIN MENU«. Observe the instructions ⇒...
  • Page 155 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Hold the button -2- on the windscreen wiper lever pressed for longer than 1 second. This will show the information display of the »MAIN MENU«. Observe the instructions ⇒...
  • Page 156 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 WARNING When resetting the service interval display with vehicle diag‐ nosis, measurement and information system -VAS- , note the following: Remove the checkmark at the “work with targeted fault finding”...
  • Page 157 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Vehicles without an information display – Switch off ignition. – Hold button -3- pressed and at the same time turn on the ig‐ nition until a “wrench” symbol is displayed on the dash panel insert display: –...
  • Page 158 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Hold button -3- pressed and at the same time turn on the ig‐ nition until a “wrench” symbol is displayed on the dash panel insert display: –...
  • Page 159 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 6.10.4 Reset service interval display from MY 2016 WARNING The vehicles are equipped with a two-channel service interval display with a different service message. This two-channel service interval display must be reset in 2 steps.
  • Page 160 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 WARNING ♦ Vehicles with variable service intervals (QI6) by default are automatically recoded to fixed service intervals as a result of this procedure. ♦ The coding can only be reset to variable service intervals (QI6) with the -VAS- if the following conditions are met ⇒...

  • Page 161: Changing The Code Of The Service Intervals

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Switch on ignition. – Hold down the button -1- until the following message 0.0/SET is displayed in the instrument cluster: Delete inspection? – Release button -1- , press again and hold.
  • Page 162 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 and legislation of the relevant country ⇒ Owner's Manual for the headlight beam setting device . Test and setting conditions • Tyre pressure o.k. • Lenses must neither be damaged nor soiled.
  • Page 163 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Caution The inclination value is marked on the top of the headlight housing. The headlights must be set to this value. The inclination value in “%” does not have a minus symbol.

  • Page 164: Checking The Operation Of The Fog Lights With The "Corner" Function (Static Cornering Light)

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Note To make it easier to determine the kink -4-, alternately cover ♦ and release the left half of the headlight (in the direction of motion) Afterwards, check the low beam again.

  • Page 165: Checking The Fog Lights

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 6.14 Checking the fog lights Note The headlight setting change is a repair measure. ♦ Headlight adjustment is charged separately. ♦ Inspecting the headlight beam setting – Check whether the light/dark limit touches the adjusting line and runs horizontally over the total width of the control screen.

  • Page 166: Time-Delayed Locking Mechanism After Closing The Tailgate - Activate/Deactivate

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Connect the vehicle diagnosis, measurement and information system -VAS- with corresponding diagnostic cable. Connect the diagnostic unit to the diagnostic connector ⇒ “6.7 Connect diagnostic unit”, page 145 –...

  • Page 167: Replace Ocu Control Unit

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 6.18 Replace OCU control unit ( control unit for emergency call module and commu‐ nication unit - J949- ) – Remove OCU control unit ( control unit for emergency call module and communication unit - J949- ) ⇒...
  • Page 168 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 • The status LED -2- of the ERA Glonass system is then lit green at the latest within approx. 2 minutes after ignition is switched If the status LED -2- of the ERA Glonass system is green, the system is ready.

  • Page 169: Era Glonass: Run System Test

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 6.20 ERA Glonass: run system test WARNING To run the ERA Glonass system test, the ERA Glonass system must active ⇒ “6.19 ERA Glonass: check that the emergency call system is ready”, page 163...
  • Page 170 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Open “SOS” cap in -direction of arrow-. Emergency call button Status LED Button for test emergency call – Press the button for test emergency call -3- for 3 seconds (e.g.

  • Page 171: Škoda Connect Services

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 6.21 Škoda Connect services ⇒ “6.21.1 Check that Škoda Connect services work, enable work‐ shop mode - before beginning service and repair work on the vehicle”, page 167 ⇒...

  • Page 172: Body

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Body ⇒ “7.1 Airbag: check for proper operation”, page 168 ⇒ “7.2 Front passenger airbag: check ON/OFF is working and switch to ON ”, page 168 ⇒ “7.3 Inspecting underbody protection for damage”, page 169 ⇒...

  • Page 173: Inspecting Underbody Protection For Damage

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 After the ignition is switched on the airbag warning light “PAS‐ SENGER AIRBAG OFF” -arrow- must light up in the centre of the dash panel for a few seconds. Then the warning light goes out for approx.

  • Page 174: Checking Body Paintwork And Underbody Protection For Damage (Before Sale)

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Checking body paintwork and under‐ body protection for damage (before sale) Scope of testing applies to: Pre-Delivery Inspection -PDI- (Export) Pre-sales Inspection - domestic (Czech Republic) Delivery Inspection (Export)
  • Page 175 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Note If fluid is filled into the washer fluid reservoir, add windscreen ♦ washer fluid (in summer) or an antifreeze (if there is a risk of frost).
  • Page 176 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Set the position of the windscreen wiper arms in such a way that the window edge maintains the dimension -a- and -b-. a - 27 +2/-2 mm...
  • Page 177 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 For Spaceback vehicles Version -I- a = 183 ± 2 mm Version -II- a = 52 ± 2 mm Inspect rear window spray nozzle For Sedan vehicles The spray should strike the rear window in the points -arrows- when the vehicle is stationary.

  • Page 178: Door Locks, Locking Buttons And Child Lock: Check Functioning Correctly

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 On vehicles with reverse camera cleaning system, the spray should be applied to the area -1-. Note If the spray flows out unevenly or insufficiently, replace the handle (repair measure).

  • Page 179: Replacing The Dust And Odour Filter Element

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Rear right door – Turn the slot of the child safety lock into position -B-, the child safety lock is activated. The inside door lock is now blocked. The door can only be opened from the outside.

  • Page 180: Stick The Sticker Škoda Assistance

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Sticking the vehicle data sticker into the Owner's Manual – Stick the vehicle data sticker -2- onto the second inside back page of the Owner's Manual (left half) under “Documentation of vehicle delivery”...

  • Page 181: Front Flap Lock: Lubricate

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Check cleanliness of the support wedge surfaces, if necessary clean these surfaces from mechanical contaminations and corrosion. – Check the turning of the key in the lock.
  • Page 182 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Attach the “ŠKODA CONNECT” mirror tag -arrow- to the in‐ terior mirror. 7. Body...

  • Page 183: Exhaust-Emission Analysis

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Exhaust-emission analysis ⇒ “8.1 Exhaust-Emission Analysis on Models with Petrol En‐ gines”, page 179 ⇒ “8.2 Exhaust-Emission Analysis on Models with Diesel En‐ gines”, page 182 Exhaust-Emission Analysis on Models...
  • Page 184 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Caution ♦ A lit exhaust emissions warning lamp in the dash panel insert indicates an error in the exhaust-related systems. These faults (including sporadic ones) are stored in event memory.
  • Page 185 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Test values for exhaust emission analysis on models with petrol engines The values are valid for the date of issuing of this workshop man‐ ual. Engine identification charac‐...

  • Page 186: Exhaust-Emission Analysis On Models With Diesel Engines

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Engine identification characters Engine temperature Catalyst warming-up time Recommended idling speed (rpm) CO content at idle speed (measured after catalyst) Recommended increased idling speed (rpm) Lambda value when engine is running at fast idling...
  • Page 187 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Test conditions for vehicles with EOBD • Faultless function of the engine without extraordinary inequal‐ ities in the engine running behaviour. • Oil temperature at least 80 °C •...
  • Page 188 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Note All tubes and plug connections, which had been removed or ♦ disconnected for the test and adjustment, must be correctly re-inserted or connected. The exhaust gas probe must be fully inserted into the exhaust ♦...
  • Page 189 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Engine identification characters CUSB CXMA Soot emission max. opacity value (1/m) - homologation value Probe no. Measurement mode Measurement time slice 0.5 s 0.5 s 18) The PR number on the vehicle data sticker (valid only for cars manufactured up to CW 45/2017) and in the electronic information system ⇒...
  • Page 190 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 An example arrangement of PR numbers on the vehicle data sticker -arrow-. Note The standard position of the PR number on the vehicle data ♦ sticker is in the area -arrow-.

  • Page 191: Miscellaneous

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Miscellaneous ⇒ “9.1 Tow starting/Towing”, page 187 ⇒ “9.2 Road test”, page 188 ⇒ “9.3 Raise vehicle”, page 189 Tow starting/Towing Note A towing rope or towing bar must only be fitted to the appro‐...

  • Page 192: Road Test

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Remove cap for towing lug -in direction of arrow- and store cap. When installing, position the cap again on the towing lug. Note Comply with the legal regulations on towing.

  • Page 193: Raise Vehicle

    Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 – Check automatic gearbox: selector lever setting, selector lever lock, switching response, display in the dash panel insert. – Inspect steering clearance of the vehicle standing on its wheels, with engine running by turning the steering wheel one way and then the other (wheels straight ahead).
  • Page 194 Rapid NH 2013 ➤ , Rapid NH 2014 ➤ Maintenance - Edition 06.2018 Rear fixation point -arrow A- WARNING ♦ To avoid damage use a suitable rubber or wood insert. ♦ Under no circumstances must the vehicle be placed on the engine, gearbox, front or rear axle.

This manual is also suitable for:

Rapid nh 2014

Table of Contents