Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Graco Manuals
  4. Paint Sprayer
  5. Inline HD 245820
  6. Instructions-parts list manual

Graco Inline HD 245820 Instructions-Parts List Manual

Texture gun
Hide thumbs Also See for Inline HD 245820:

Advertisement

Quick Links

Download this manual
Instructions-Parts List
Inline HDt Texture Gun
Waterbase Compatible
280 bar (28 MPa, 4000 psi) Maximum Working Pressure
Model 245820, Series B
Ball end valve needle - abrasive material compatible
U.S. Patent No. Des. 342,654
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.

Table of Contents

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . .
2
3
5
10
11
12
12
309495E
ti13864

Advertisement

loading

Related Manuals for Graco Inline HD 245820

Summary of Contents for Graco Inline HD 245820

  • Page 1: Table Of Contents

    ......Graco Phone Number ....

  • Page 2: Warning

    ADVERTÊNCIA WARNING Perigo de incêndio e explosão: os solventes e os vapores da pintura Fire and explosion hazard: Solvent and paint fumes can ignite or poderão explodir ou incendiar. explode. Para ajudar a evitar incêndio e explosão: To help prevent a fire and explosion: DUtilize unicamente em áreas extremamente bem ventiladas.

  • Page 3: Operation

    Operation Pressure Relief Procedure Gun Trigger Safety 1. To lock gun safety, release trigger and rotate safety toward trigger, Fig. 1. WARNING NOTE: Do not force trigger valve open with safety engaged. This could result in component failure. INJECTION HAZARD System pressure must be manually relieved to prevent system from starting or spraying accidentally.
  • Page 4 Operation Spraying Relieve pressure; page 3. 2. Lock gun trigger safety. Vent 3. Install tip and guard. 4. Use lowest possible pump pressure to obtain desired flow rate. ti13867a Fig. 3 Flushing Safety 5. Unlock gun trigger safety. WARNING 6. Squeeze trigger. Fluid flow begins with slightest FIRE AND EXPLOSION HAZARD pressure on trigger and stops when trigger is To reduce risk of a fire, explosion, or...

  • Page 5: Service

    2. Disconnect gun from hose. trigger safety is damaged. Reassemble gun or return it to your nearest Graco distributor. Do 3. Fig. 4. Loosen stem nut (1) and spring housing not use gun until problem is corrected.
  • Page 6 Service Valve Stem and Seal Service 11. Lubricate and torque seal retainer (27) into gun body (17) to 100–125 in-lb (11.3–14.1 NSm). If fluid leaks past v-block seal (3), v-block seal or valve stem (24) may be worn or damaged. Use following CAUTION procedure to replace v-block seal or valve stem.
  • Page 7 Service ti13868a NOTES: Torque to 6–10 in-lb (0.68–1.13 NSm) Torque to 26–32 ft-lb (35.3–43.4 NSm) Apply lithium base grease to threads Apply lithium base grease Torque to 100–125 in-lb (11.3–14.1 NSm) Apply high strength anaerobic sealant (red) Fig. 4 Gun Disassembly and Assembly 4.
  • Page 8 Service Gun Disassembly and Assembly 11. Install fluid tube assembly (19) through gun handle (14) and screw it into gun body (17). Torque fluid (continued) tube assembly (19) to 200–250 in-lb (22.6–28.2 NSm). Secure fluid tube assembly with setscrew Assembly (42), and torque setscrew to 6–10 in-lb (0.7–1.13 1.
  • Page 9 Service ti13869a NOTES: Torque to 6–10 in-lb (0.68–1.13 NSm) Torque to 200–250 in-lb (22.6–28.2 NSm) Torque to 26–32 ft-lb (35.3–43.4 NSm) Apply low strength anaerobic sealant (blue) Apply lithium base grease to threads Apply lithium base grease Apply high strength anaerobic sealant (red) When removing fluid hose, use wrench on end of fluid tube assembly (19) hex to avoid loosening fluid tube assembly (19) Torque to 100–125 in-lb (11.3–14.1 NSm)

  • Page 10: Parts

    Parts Model 245820 † 14 32 † † † ti13869a Ref. Ref. Part No. Description Qty. Part No. Description Qty. 100975 NUT, hex; No. 5–40 188247 SCREW, spring adjustment 102233 BALL; stainless steel 236234 STEM, valve 102921 SEAL, v-block; polyurethane 188271 RETAINER, seal 102924...

  • Page 11: Technical Data

    Technical Data Maximum Working Pressure ..4000 psi (280 bar) Weight ......33.79 oz. (958 g) Outlet Port Size .

  • Page 12: Graco Warranty

    With the exception of any special extended or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.

This manual is also suitable for:

Inline hd b series