A A c c r r a a c c k k e e d d f f r r a a m m e e c c r r e e a a t t e e s s a a t t i i p p p p i i n n g g r r i i s s k k . . I I f f c c r r a a c c k k e e d d f f r r a a m m e e i i s s

f f o o u u n n d d , , i i m m m m e e d d i i a a t t e e a a t t t t e e n n t t i i o o n n i i s s n n e e e e d d e e d d t t o o r r e e p p a a i i r r t t h h e e f f r r a a m m e e

b b y y h h a a v v i i n n g g i i t t p p r r o o f f e e s s s s i i o o n n a a l l l l y y r r e e p p a a i i r r e e d d b b y y a a w w e e l l d d e e r r , , o o r r h h a a v v i i n n g g

t t h h e e f f r r y y e e r r r r e e p p l l a a c c e e d d . .

To inspect the casters and frame do the following:

• Inspect casters and the tube steel frame by removing side panels and using a

flashlight to look for cracking or bent frame (Figure 1).

• Inspect that the fryer sits level, casters are mechanically sound to hold the weight of

the fryer and the tube steel frame is not cracked or bent.

• If the fryer is sitting out of level, inspect the condition of the floor. Have any missing

or cracked tiles replaced.

• If there is a slope due to a floor drain, the fryer may need to be repositioned so the

caster is not near this slope.

8 8 . . 8 8 I I n n s s p p e e c c t t t t h h e e P P o o w w e e r r C C o o r r d d

F F i i r r e e R R i i s s k k a a n n d d E E l l e e c c t t r r i i c c a a l l S S h h o o c c k k P P o o s s s s i i b b l l e e . . I I f f a a n n y y o o f f t t h h e e s s e e

c c o o n n d d i i t t i i o o n n s s a a r r e e f f o o u u n n d d , , t t a a k k e e t t h h e e f f r r y y e e r r o o u u t t o o f f s s e e r r v v i i c c e e u u n n t t i i l l a a

n n e e w w p p o o w w e e r r c c o o r r d d o o r r p p l l u u g g c c a a n n b b e e i i n n s s t t a a l l l l e e d d . . A A l l w w a a y y s s a a d d h h e e r r e e t t o o

l l o o c c a a l l e e l l e e c c t t r r i i c c a a l l c c o o d d e e u u p p o o n n i i n n s s t t a a l l l l a a t t i i o o n n o o f f t t h h e e p p o o w w e e r r c c o o r r d d . .

Replace any power cord with torn or damaged sheathing, exposed wire or fraying.

Replace the plug if there are any signs of damage, cracking, loose wires, burnt

connections.

• Check the data plate mounted just above the lid, on the left side of the back shroud,

to determine the correct power supply.

• Ensure the appliance is equipped with an external circuit breaker which will

disconnect all ungrounded (unearthed) conductors. The main power switch on this

appliance does not disconnect all line conductors.

227

Table of Contents