Advertisement
1. overview
1.2 Advice for the installer
The installation and fi rst ignition of the boiler must be
performed by qualifi ed personnel in compliance with
current national regulations regarding installation,
and in conformity with any requirements established
by local authorities and public health organisations.
After the boiler has been installed, the installer must
ensure that the end user receives the declaration
of conformity and the operating manual, and should
provide all necessary information as to how the boiler
and the safety devices should be handled.
This appliance is designed to produce hot water for domestic
use.
It should be connected to a heating system and a distribution
network for domestic hot water, both of which must be
compatible with its performance and power levels.
The use of the appliance for purposes other than those
specifi ed is strictly forbidden. The manufacturer cannot
be held responsible for any damage caused by improper,
incorrect and unreasonable use of the appliance or by the
failure to comply with the instructions given in this manual.
Installation, maintenance and all other interventions
must be carried out in full conformity with the governing
legal regulations and the instructions provided by the
manufacturer.
Incorrect installation can harm persons,
animals and possessions; the manufacturing company shall
not be held responsible for any damage caused as a result.
The boiler is delivered in a carton. Once you have removed all
the packaging, make sure the appliance is intact and that no
parts are missing. If this is not the case, please contact your
supplier.
Keep all packaging material (clips, plastic bags, polystyrene foam,
etc.) out of reach of children as it may present a potential hazard.
In the event of a fault and/or malfunction, turn the appliance
off, turn off the gas cock and do not attempt to repair it
yourself. Contact a qualifi ed professional instead.
Before any maintenance or repair work is performed on the
boiler, make sure you have disconnected it from the electricity
supply by switching the external bipolar switch to the "OFF"
position and removing the fuse.
All repairs, which should only be performed using original
spare parts, should be carried out by a qualifi ed professional.
Failure to comply with the above instructions could
compromise the safety of the appliance and invalidate all
liability on the part of the manufacturer.
In the event of any maintenance or other structural work in
the immediate vicinity of the ducts or fl ue gas exhaust devices
and their accessories, switch the appliance off by switching
the external bipolar switch to the "OFF" position and shutting
off the gas control valve. When the work has been completed,
ask a qualifi ed technician to check the effi ciency of the ducting
and the devices.
Turn the boiler off and turn the external switch "OFF" to clean
the exterior parts of the appliance.
Clean using a cloth dampened with soapy water. Do not use
aggressive detergents, insecticides or toxic products. If the
appliance is used in full compliance with current legislation,
it will operate in a safe, environmentally-friendly and cost-
effi cient manner.
If using kits or optional extras, make sure they are authentic.
4
1.3 CE labelling
The CE mark guarantees that the appliance conforms to the
following directives:
- 2009/142/CEE
relating to gas appliances
- 2004/108/CEE
relating to electromagnetic compatibility
- 92/42/CEE
relating to energy effi ciency
- 2006/95/CEE
relating to electrical safety
1.4 Symbols used on the data plate
1
1
3
3
8
9
12
13
10
11
Legend :
1. Brand
2. Manufacturer
3. Boiler model - Serial number
4. Commercial reference
5. certifi cation number
6. Destination country - gas category
7. Gas setting
8. Installation type
9. Electrical data
10. Maximum domestic hot water pressure
11. Maximum heating pressure
12. Boiler type
13. NOx class / Effi ciency
14. Input rating nominal heating
15. Power ouput heating
16. DHW specifi c fl ow rate
17. Boiler output effi ciency
18. Input rating nominal DHW
19. Gases which may be used
20. Minimum ambient temperature for use
21. Max. central heating temperature
22. Max. domestic hot water temperature
2
4
5
6
7
MAX
MIN
Q
P
15
60/80°C
16
17
19
18
20
21
22
Fig. 1.1
Advertisement
