Panasonic Panafax UF-885 Service Manual page 144

Panasonic UF-885 / 895
Code Mode
420 RCV
421 RCV
422 XMT
427 G3 RCV
433 XMT
RCV
434 XMT or RCV
436 G3 RX
456 RCV
457 RELAYXMT
CONF.XMT/
POLL
459 RCV
490 RCV
494 RCV
495 XMT/RCV
496 XMT
501 XMT/
RCV(V.34)
502 XMT/
RCV(V.34)
503 XMT/
RCV(V.34)
504 RCV/V.34
(Polling)
505 XMT/V.34
(Polling)
540 XMT ECM
541 XMT ECM
542 XMT ECM
543 XMT ECM
544 XMT ECM
550 RCV ECM
554 RCV ECM
555 RCV ECM
570 RCV
571 XMT
580 XMT
581 XMT
601 XMT
144
Information Codes
Phase Description of Problem
B T1 timer (35 sec.) elapsed without detecting 300
bps signal.
B Busy Tone is detected after sending NSF Signal. Remote station disconnectes the line.
B Content of NSF (or DIS) or NSC (or DTC) was
invalid.
B DCN received to NSF/CSI/DIS transmitted.
B, D T.30 Protocol abnormal.
B CD (response from Modem) did not turn OFF
within 180 sec. after receiver detected FLAG
signal.
C DCN received after transmitting FTT.
B Received relay transfer request or confidential
document to distribute to a end receiving station
or all confidential mailboxes are used.
B Remote unit does not have Relayed XMT or
Confidential Comm. capability.
C Failed training in Phase C.
C Sum of error line exceeded the limit (Parameter
70) by 64 lines.
C Interval between two EOLs was more than 10
sec. when receiver received message data.
C During reception, CD turned OFF or continued
ON for long time.
During communication, lost loop - current.
C CS of modem is not able to turn ON.
B Remote unit does not have Modem
compatibility.
B, C, D During reception, CD turned OFF or continued
ON for long time.
During communication, lost loop - current.
B, C, D CS of modem is not able to turn ON during
training.
B Polling is rejected from the remote station.
B Polling XMT is rejected.
B No response after transmitting 3rd CTC or DCN
received.
D No response after transmitting 3rd EOR or
received DCN.
D No response to the 3rd RR transmitted or
received DCN.
D T5 timer (60 sec.) elapsed without MCF.
D Stopped Transmission after EOR Transmission. Line is faulty.
C Timer between frames in phase C has elapsed. Defective remote station.
D Transmitted ERR after receiving EOR.
D Transmitted PIN after receiving EOR.
B Password or machine code did not match during
remote diagnostic communication.
B Remote unit did not have the remote diagnostic
function.
B Sub-address transmission to a unit that has their
DIS bit 49 (NSF bit 155) OFF.
B Sub-address Password transmission to a unit
that has their DIS bit 50 (NSF bit 156) OFF.
ADF Door was opened during ADF
transmission.
Cause
There is wrong incoming call.(non-facsimile
communication)
Transmitter is defective.
FCB PCB or LCU PCB is defective.
Wrong number is dialed.
There is an incompatibility.
The interface is incompatible.
Defective remote station.
Remote unit is defective.
FCB PCB or LCU PCB is defective.
Transmitter is defective or incompatible.
Line quality is poor.
Line quality is poor. (Training signal is distorted
due to line noise)
FCB PCB or LCU PCB are defective.
Line quality is poor.
FCB PCB or LCU PCB are defective.
Transmitter is defective.
Line quality is poor. (EOL is damaged due to
line noise)
FCB PCB or LCU PCB are defective.
Line is disconnected.
Transmitter is defective.
FCB PCB or LCU PCB are defective.
FCB PCB is defective.
Line is disconnected.
Transmitter is defective.
FCB PCB or LCU PCB are defective.
FCB PCB is defective.
Line is disconnected.
No polling document is set.
No polling document is set.
Incompatible interface.
Line is faulty.
LCU PCB abnormal.
Remote unit is abnormal.
Remote unit is abnormal.
LCU PCB abnormal.
Faulty line.
Faulty line and Operator Call requested by RX
side.
Sub-address transmission to a unit that has no
Sub-address function.
Sub-address transmission to a unit that has no
Sub-address function.