Gigabyte W131-X30 Quick Installation Manual

Make sure the system is not turned on or connected to AC power.

Always handle boards carefully. They can be extremely sensi-tive to electrostatic discharge (ESD). Hold boards only by their edges.

After removing a board from its protective wrapper or from the system, place the board component side up on a grounded, static free surface.
Use a conductive foam pad if available but not the board wrapper. Do not slide board over any surface.
Risk of explosion if battery is replaced incorrectly or with an incorrect type. Replace the battery only with the same or equivalent type recommended

by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
ME
Clear
Default 3
Force
CMOS
2
Update
CLR_CMOS Enable 1
ME_UPDATE
30
24 25 26 28 29
Power On
23
Select
S3_MASK
27
22
21
20
Default Enable
19
Password
Clear
1 2 3
BIOS_PWD
Default Enable
ME
Recovery
1 2 3
18
ME_RCVR
Default Enable
BIOS
Recovery
17 16 15 14 13 12 11
1 2 3
BIOS_RCVR
System Appearance
1
2
No. Desription
1 USB 2.0 ports
2 Power button with LED
Power button/ LED:
State Description
Green On System is powered on.
System is not powered on or in ACPI S5 state (power off)
Off
System is in ACPI S4 state (hibernate mode)
PN:12xx
W131-X30 Quick Installation Guide
Pre-installation Cautions
Motherboard Components
Default
No. Code
Enable
1 MLAN
1 2 3 4 2 USB2_LAN1
3 USB2_LAN2
4 COM1_VGA
5 PMBUS
5
6 SYS_FAN1
7 P12V_AUX
8 CPU_FAN
6 9 SYS_FAN2
10 ATX1
11 SD_CN
7
S3
12 SATA_4
3
Default
2
13 SATA_5
Enable
1
14 SATA_2
15 SATA_3
16 SATA_1
17 SATA_0
CPU
18 FP_2
19 FP_1
20 F_USB2
21 IPMB
8
22 TPM
23 BP_1
24 COM2
DIMM_P0_A0 25 PCIE_1
DIMM_P0_A1 26 PCIE_2
27 BAT
DIMM_P0_B0
28 PCIE_3
DIMM_P0_B1
29 PCIE_4
9
30 LED_BMC1
10
1
2
3
4
5
6
7
No. Desription
1 Power supply module cord socket
2 Serial port
3 VGA port
4 USB 3.0 ports
5 GbE LAN ports
6 10/100/1000 Server management LAN port
7 PCIe card bay
10/100/1000 LAN LED:
Speed LED Link/Activity
LED
State Description
Yellow On 1Gbps data rate
Green On 100Mbps data rate
Off
10Mbps data rate
Power Supply
2
1
Description
Server managemnt LAN port
LAN port #1 (top) / USB 3.0 ports (bottom)
LAN port #2 (top) / USB 3.0 ports (bottom)
Serial port (top) / VGA port (bottom)
PMBus connector
System fan connector#1
8 pin power connector (for CPU)
CPU fan connector
System fan connector#2
24 pin main power connector
SD card connector
SATA 3 6Gb/s connector
SATA 3 6Gb/s connector
SATA 3 6Gb/s connector
SATA 3 6Gb/s connector
SATA 3 6Gb/s connector
SATA 3 6Gb/s connector
Secondary front panel header
Front panel header
USB 2.0 header
IPMB connector
TPM connector
HDD back plane board header
Serial port cable connector
PCI Express x8 slot (running at x4)
PCI Express x16 slot (running at x8)
Battery socket
PCI Express x1 slot
PCI Express x16 slot (running at x8)
BMC firmware readiness LED
PCI Express Card
2
1
3
Optical Disc Drive
2
1
System Cover
1
2
1
System Components
6
1
2
3
4
3
5
No. Desription
1 Optical disc drive (Option)
2 Front bezel door
3 Hard Disk Drives
4 Motherboard
5 PCIe card bay
6 Power supply module
Installing CPU/ 安装 CPU
Memory Population Configuration/ 安装内存
Ranks Per
Type DIMM and
Data Width
UDIMM
Unbuffered SR
DDR4 ECC
UDIMM
Unbuffered
DR
DDR4 non-ECC
 All channels in system run at the fastest common frequency.
 Mixing ECC and non-ECC UDIMMs anywhere on the platform is not supported.
 1 and 2 DPC is supported at 2133MHz.

所有通道模式以最快的频率速度运行。

此主板不支持ECC与非ECC内存模组混合使用。
 1 2 DPC 2133MHz
与 均支持
Hard Disk Drive
2
1
Front Bezel Door
2
1
NOTE!
Remove side cover before removing
the front bezel door
Speed (MT/s);
Slot Per Channel (SPC) and
DIMM Per Channel (DPC)
Supported
Voltage
2 Slot Per Channel
1DPC 2DPC
1.2V 2133 2133
1.2V 2133 2133
速度。
1
2