Front View; Utilities Entry Data; Rear View - York SUNLINE 2000 D3CE 036 Installation Instruction

(Direct-Drive Units)
FIELD-SUPPLIED
DISCONNECT SWITCH
LOCATION
CONTROL
FILTER ACCESS
BOX ACCESS
OPENING FOR
PRESSURE CHECK
(829)
⁄
5
32
8
(19)
⁄
3
" PVC FEMALE
4
COND. DRAIN
⁄
7
(1140) 44
8
(See Detail "A")
A, B
WIRING ENTRY
(See Detail "B")
(137)
⁄
3
5
8
(200)
BOTTOM SUPPLY &
RETURN AIR OPENINGS
(SEE NOTE)
B - POWER WIRING ENTRY
A - CONTROL WIRING ENTRY
CLEARANCES (mm/in.)
Front
Back
Left Side (Filter Access)
Right Side (Cond. Coil)
1
Below Unit
2
Above Unit
NOTE:
Units and ductwork are approved for zero clearance to combustible
materials when equipped with electric heaters.
1
Units may be installed on combustible floors made from wood or
class A, B or C roof covering material. (Applicable in USA only).
2
Units must be installed oudoors. Overhanging structures or shrubs
should not obstruct the outdoor coil nor the fan outlet.
(699)
⁄
1
27
2
(495)
⁄
1
19
2
DETAIL "A"
UNIT WITH ECONOMIZER RAIN HOOD
FIG. 5 - DIMENSIONS & CLEARANCES - 036 - 076 UNITS
Unitary Products Group
BLOWER
ACCESS
OPENING FOR
PRESSURE CHECK

FRONT VIEW

(2089) 82
(292)
11
(445)
⁄
1
17
2
⁄
1
(165) 6
2
⁄
1
(445) 17
⁄ 2
3
(171) 6
4
⁄
1
(206) 8
8
⁄
7 UNIT BASE WITH RAILS
7
8
Shown separately to illustrate bottom
duct openings and power connection
locations.
NOTE: For curb-mounted units, refer to the
duct hanger dimensions of the curb for the
proper size of the supply and return air
⁄
3 duct connections.
(213) 8
8
607/24
305/12
(Less Economizer)
914/36
(With Economizer)
607/24
(Less Economizer)
914/36
(With Economizer)
607/24
20/0
1829/72
(For Condenser Air
Discharge)
(19)
⁄
3
" CONDENSATE
4
DRAIN
(must be trapped)
(502)
⁄
3
19
4
(1140)
⁄
7
44
8
OUTDOOR
COIL
COMPRESSOR
ACCESS
ELECTRIC
HEAT
⁄
1
4
ACCESS
(64)
⁄
1
2
2
⁄
1
2
(445)
⁄
1
17
2
(165)
(445)
⁄ ⁄
1
1 6
17
2
2

REAR VIEW

SIDE SUPPLY AND RETURN
AIR OPENINGS
(416)
⁄
3
16
8
(121)
⁄
5
4
8
(260)
⁄
10 1
4
DETAIL "B"
UNIT WITH FIXED OUTDOOR
AIR / BAROMETRIC RELIEF RAIN HOOD
DUCT COVERS - Units are shipped with all air duct
openings covered.
For side duct applications;
1.Remove and discard the supply and return air duct
covers.
2.Connect ductwork to duct flanges on the rear of the
unit.
For bottom duct applications;
1. Remove the side supply air duct cover to gain
access to the bottom supply air knockout panel.
2. Remove and discard the bottom knockout panel.
3. Replace the side duct cover.
4. With filter section access panel removed from the
unit, remove and discard the bottom return air
knockout panel.
5. Replace the filter access panel.
All dimensions are in millimeters and inches.
They are subject to change without notice. Cer-
tified dimensions will be provided upon request.

UTILITIES ENTRY DATA

(292)
⁄
1
11
2
KNOCKOUT
(76)
3
HOLE SIZE
(292)
(DIA.), mm/in.
⁄
11 1
2
(117)
⁄
5 A 22 /
4
8
(
200)
B 51 / 2 **
⁄
7
7
8
*
Knockouts in the bottom of the unit can be located
by the slice in the insulation.
**
Do not remove the 2" knockout ring.
(260)
⁄
1
10
4
B
A
(1140)
⁄
7
44
8
(121)
3
4
530.26-N1YI
USED FOR
Control Wiring
⁄
7
* (Side or
8
Bottom)**
Power Wiring
(Side or
Bottom)
AIR FLOW LEGEND
RETURN AIR
SUPPLY AIR
OUTDOOR AIR
(89)
OUTDOOR AIR
⁄
1
3
2
(Economizer)
⁄
1
(210) 8
4
⁄
8
7