Troubleshooting; Side Burner Troubleshooting - Weber Summit E-670 Owner's Manual

PROBLEM
Burners burn with a yellow or orange flame, in
conjunction with the smell of gas. (This is normal for the
burner lighting tube).
Symptoms:
Burners do not light, or Burners have a small flickering
flame in the HI position, or Grill temperature only
reaches 250° to 300° in the HI position.
Some countries have regulators with an excess gas flow
safety device.
Burner does not light, or flame is low in HI position.
Experiencing flare-ups:
m CAUTION: Do not line the slide-out
grease tray with aluminum foil.
Burner flame pattern is erratic. Flame is low when
burner is on HI. Flames do not run the whole length of
the burner tube.
Inside of lid appears to be "peeling." (Resembles paint
peeling.)
Cabinet doors are not aligned.
Grill seems to lose heat when cooking in cold weather
temperatures of 10°C (50°F) or colder.
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our
web site. Log onto www.weber.com.
PROBLEM
Side Burner does not light.
Some countries have regulators with an excess gas flow
safety device.
Flame is low in HI position.
Push button ignition does not work.
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our
web site. Log onto www.weber.com.
28

TROUBLESHOOTING

CHECK
Inspect Spider/Insect screens for possible obstructions
(blockage of holes).
The excess gas flow safety device, which is part of the
grill-to-cylinder connection, may have been activated.
Is LP fuel low or empty?
Is fuel hose bent or kinked?
Does burner light with a match?
Did you use the snap igniter several times until the main
burner lit? Refer to "MAIN BURNER IGNITION".
Does the igniter work? Do you see a spark when you
repeatedly use the snap igniter?
Are you preheating grill in the prescribed manner?
Are the cooking grates and FLAVORIZER bars heavily
coated with burned-on grease?
Is the slide-out grease tray dirty and not allowing grease
to flow into catch pan?
Are burners clean?
The lid is porcelain enamel or stainless steel, not paint. It
cannot "peel". What you are seeing is baked on grease that
has turned to carbon and is flaking off.
THIS IS NOT A DEFECT.
Check the adjustment pin on the bottom of each door.
Is there frost/ice on the outside of the LP cylinder?

SIDE BURNER TROUBLESHOOTING

CHECK
Is gas supply off?
The excess gas flow safety device, which is part
of the grill-to-cylinder connection, may have been
activated.
Is the fuel hose bent or kinked?
Does burner light with a match?
Is there a fresh battery installed?
Are the wires connected properly to the igniter
module?
Is there plastic wrapping around the new battery?
SOLUTION
Clean Spider/Insect screens. Refer to "ANNUAL
MAINTENANCE".
To reset the excess gas flow safety device, turn all burner
control knobs and the cylinder valve off. Disconnect the
regulator from the cylinder. Turn burner control knobs to
HI. Wait at least 1 minute. Turn burner control knobs to
OFF. Reconnect the regulator to the cylinder. Turn cylinder
valve on slowly. Refer to "MAIN BURNER IGNITION".
Refill LP cylinder.
Straighten fuel hose.
If you can light burner with a match, then check the ignition
system.
Make sure you hold the control knob in for two seconds
after snapping the igniter and seeing the orange flame
from the burner lighting tube.
Try manually lighting the burner. Refer to "MAIN BURNER
MANUAL IGNITION". Call Customer Service.
All burners on HI for 10 to 15 minutes for preheating.
Clean thoroughly. Refer to "CLEANING".
Clean slide-out grease tray.
Clean burners. Refer to "MAINTENANCE".
Clean thoroughly. Refer to "CLEANING".
Loosen adjustment nut(s). Slide door(s) until aligned.
Tighten nut.
The liquid propane in the cylinder turns to vapour too
slowly to supply the burners with gas. This is due to the
air temperature cooling the LP cylinder, which slows the
vaporisation process. Turn off burner control knobs and
the LP cylinder. Replace with a spare LP cylinder and
resume cooking.
SOLUTION
Turn gas supply on.
To reset the excess gas flow safety device close the LP tank valve
and turn all burner control knobs to the OFF position. Open the
grill and side burner lids. Slowly turn the LP tank valve until it
is completely open. Wait several seconds then ignite your side
burner. Refer to "SIDE BURNER IGNITION".
Straighten hose.
If match lights burner, check igniter. Refer to "SIDE BURNER
MAINTENANCE".
Verify that the battery is in good condition and installed correctly.
Refer to "ELECTRONIC IGNITION SYSTEM OPERATIONS."
Be sure that wires are correctly inserted into terminals on
ignition box. Refer to "SIDE BURNER MAINTENANCE."
Remove plastic wrapping.