Sony 5500 Operation Manual page 82

Automatic time data changes during IN/OUT
point data entry or modification
The table below shows the automatic changes that occur in
time data when either the IN point or OUT point is
changed.
When IN point data is entered or modified:
Status of input data
The time sequence of the IN/
OUT point data is correct.
The time sequence of the IN/
OUT point data is not correct.
The OUT point has not been
input.
When OUT point data is entered or modified:
Status of the input data
The time sequence of the IN/
OUT point data is correct.
The time sequence of the IN/
OUT point data is not correct.
The IN point has not been
input.
Changing Tk data
Use the cursor buttons to move the cursor to the take data
to be changed. Then use the numeric buttons to change the
value. Note that values from 0 to 255 can be entered. Or,
move the cursor to the take data, and press the [F4]
(CHANGE DATA) button or the + button repeatedly to
increase the value in increments of 1. Press the – button
repeatedly to decrease the value in increments of 1. Note
that the value cannot go below 0.
Copying data
Use the cursor buttons to move the cursor to the destination
Mrk or Tk data, and press the RCL button. The Tk data
from the line above is copied to the selected line.
Changing Cut data
Use the cursor buttons to move the cursor to the cut data to
be changed, and then enter the new data using the numeric
buttons and +/– buttons. Pressing the – button enters the
tilde (~). Press the numeric buttons while pressing down
the SFT button to enter uppercase letters (A to J). Note that
a maximum of four characters can be entered.
Or, do the procedure below to change the data.
82
4-4 CUE Menu
IN point OUT point
The data is The data is
changed. unchanged.
The data is The data is
changed. deleted.
The data is The data is
changed. unchanged.
IN point OUT point
The data is The data is
unchanged. changed.
The data is The data is
unchanged. unchanged.
The data is The data is
unchanged. changed.
2 4 6
1
Press the cursor buttons to move the cursor to the cut
data to be changed.
To move the cursor using the numeric buttons
Enter the line number using the numeric buttons. Then
press the [F9] (CUENUM POINT) button. The cursor
will move to the line specified by the numeric buttons.
2
Press the [F4] (CHANGE DATA) button.
R E C D A T E [ 2 0 0 3 / 0 2 / 2 5 ]
C U T N o . E D I T
T I T L E [ i s p l a y S a m p l e
N o . T a p e F o r m a t D u r a t i o n
_
0 5 9 i 1 0 8 0 4 2 2 0 1 : 0 0 : 3 6 : 0 6
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
1 5 9 i 1 0 8 0 4 2 2
a b c d e f g h j i k l m n o p q r s t u v w x y z
0 1 2 3 4 5 6 7 8 9 [ ] ( ) < > @ + - * = ! ? : ;
$ # % & , . " \ ^ _ ' / ~ { }
S P A C E B A C K S E T
S P A C E L E T T E R
3
Press the T or t button to select a character.
R E C D A T E [ 2 0 0 3 / 0 2 / 2 5 ]
C U T N o . E D I T
T I T L E [ i s p l a y S a m p l e
N o . T a p e F o r m a t D u r a t i o n
_
0 5 9 i 1 0 8 0 4 2 2 0 1 : 0 0 : 3 6 : 0 6
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
1 5 9 i 1 0 8 0 4 2 2
a b c d e f g h j i k l m n o p q r s t u v w x y z
0 1 2 3 4 5 6 7 8 9 [ ] ( ) < > @ + - * = ! ? : ;
$ # % & , . " \ ^ _ ' / ~ { }
S P A C E B A C K S E T
S P A C E L E T T E R
4
Press the [F7] (SET LETTER) button or the cursor
center button.
The selected character is entered.
1,3
E O S [ 0 1 : 0 1 : 0 2 : 0 8 ]
] R e s t 1 0 0 %
- - -
0 1 : 0 0 : 3 6 : 0 6 - - -
' H D 1 D 2 C A M
C A N C E L S A V E /
E X I T
E O S [ 0 1 : 0 1 : 0 2 : 0 8 ]
] R e s t 1 0 0 %
- - -
0 1 : 0 0 : 3 6 : 0 6 - - -
' H D 1 D 2 C A M
S A V E /
E X I T