Kenwood NX-200 Service Manual page 52

NX-200(G)
Item
Panel tuning mode
Maximum 1) Adj item: [Nv NDEV]
Deviation Adjust: [‫]٭٭٭٭‬
(NXDN) 2) Adj item:
adjust *3 [NvL NDEV]→
[NvL' NDEV]→
[Very [NvC NDEV]→
Narrow] [NvH' NDEV]→
[NvH NDEV]
Adjust: [‫]٭٭٭٭‬
PTT: ON
Press [ ] key to store
the adjustment value.
5. Maximum 1) Adj item: [An ADEV]
Deviation Adjust: [‫]٭٭٭٭‬
(Analog) 2) Adj item:
adjust *3 [AnL ADEV]→
[AnL' ADEV]→
[Narrow] [AnC ADEV]→
[AnH' ADEV]→
[AnH ADEV]
Adjust: [‫]٭٭٭٭‬
Press [ ] key to store
the adjustment value.
[Wide] 1) Adj item: [Aw ADEV]
Adjust: [‫]٭٭٭٭‬
2) Adj item:
[AwL ADEV]→
[AwL' ADEV]→
[AwC ADEV]→
[AwH' ADEV]→
[AwH ADEV]
Adjust: [‫]٭٭٭٭‬
Press [ ] key to store
the adjustment value.
*3: Refer to the "Necessary Deviation adjustment item for each signaling and mode" table on pages 55 and 56.
Regarding Maximum Deviation (Analog), it is common with the adjustment of all analog signalings.
6. QT 1) Adj item: [An QT]
Deviation Adjust: [‫]٭٭٭٭‬
adjust *4 Deviation meter
LPF: 3kHz
[Narrow] HPF: OFF
PTT: ON
Press [ ] key to store
the adjustment value.
52
ADJUSTMENT
Condition
PC test mode
equipment
1) Adj item: [Maximum Deviation
Deviation (NXDN meter
Very Narrow)] Oscilloscope
2) Adj item: [Low],
[Low'], [Center],
[High'], [High]
PTT: Press
[Transmit] button.
Press [Apply All]
button to store the
adjustment value.
1) Adj item: [Maximum
Deviation (Analog
Narrow)]
2) Adj item: [Low],
[Low'], [Center],
[High'], [High]
Press [Apply All]
button to store the
adjustment value.
1) Adj item: [Maximum
Deviation (Analog
Wide)]
2) Adj item: [Low],
[Low'], [Center],
[High'], [High]
Press [Apply All]
button to store the
adjustment value.
1) Adj item: [QT Devia- Deviation
tion (Analog Narrow)] meter
Deviation meter Oscilloscope
LPF: 3kHz
HPF: OFF
PTT: Press
[Transmit] button.
Press [Apply]
button to store the
adjustment value.
Measurement
Test-
Unit Terminal Unit
Panel ANT Panel [Panel
Panel ANT Panel [Panel
Adjustment
Specifi cations /
Parts Method
1337Hz 1311~1363Hz
tuning
mode] [PC test mode]
[ ], Press [Apply All]
[ ] button to store the
adjustment value
[PC test after all adjustment
mode] point was adjusted.
[ ],[ ]
Write the same 2050~2150Hz
adjustment value of
"NXDN Deviation [PC test mode]
[Narrow]" for each Press [Apply All]
adjustment point. button to store the
Transmit at each adjustment value
adjustment point and after all adjustment
check that the Analog point was adjusted.
deviation is between
2050Hz and 2150Hz.
Deviation meter
LPF: 15kHz
HPF: OFF
[Panel tuning mode]
PTT: ON
[PC test mode]
PTT: Press
[Transmit] button
Write the same 4150~4250Hz
adjustment value of
"NXDN Deviation [PC test mode]
[Narrow]" for each Press [Apply All]
adjustment point. button to store the
Transmit at each adjustment value
adjustment point and after all adjustment
check that the Analog point was adjusted.
deviation is between
4150Hz and 4250Hz.
Deviation meter
LPF: 15kHz
HPF: OFF
[Panel tuning mode]
PTT: ON
[PC test mode]
PTT: Press
[Transmit] button
Write the value as 0.35kHz±0.05kHz
tuning followings.
mode] 513 (Reference
[ ], value)
[ ]
[PC test
mode]
[ ],[ ]
Remarks