8.3. Disc Tray
(1) Open the Disc Tray. (refer to Item No.2).
(2) Take the Disc Tray (p) off.
(When inserting Disc Tray, confirm the boss on the Slide
Cam set to the ditch on the Disc Tray.)
8.4. Traverse unit
(1) Remove 4 top screws (s) and 4 Dampers (p).
(2) Detach a : Traverse unit.
s : Special Screw (Front)
a : Main chassis unit
p : Disc Tray
8.5. Abandonment of Main chassis unit
(1) Remove 6 bottom screws, then detach the
p : Sub chassis (L)/(R).
(2) Remove 2 top screws then detach the c : Loading motor
ass'y.
(3) Remove 1 bottom screws, then detach the c : SW P.W.B.
ass'y.
(4) Remove 3 top S.Washers, then detach 3 p : Gears.
8.6. Abandonment of Traverse unit
(1) Remove 4 top screws, then detach the m : S.tilt plate,
p : S.tilt base, 2 m : Spring, p : Shaft holder (L)/(R).
(2) Take off m: Shaft (Main)/(Sub) from c : PU ass'y.
(3) Remove 3 bottom screws, then detach the c : T/T motor
ass'y.
(4) Remove 2 top S.Washers, then detach 2 p : Gears.
(5) Remove 2 top screws, then detach the c : Feed motor
ass'y.
※ Please abandon discretion refer to the figure below and
the Exploded view of the DVD Mechanism.
m : Spring
p : Sub Chassis (L)/(R)
p : Traverse arm
p : Slit Washer
p : Gear
s : Screw
p : Loader belt
s : Screw
p : DAMPER
m : Main chassis ass'y
p : Slide cam
s : Screw
s : Screw
c : Loading Motor & SW P.W.B. ass'y
8.3. ディスクトレイ
(1) ディスクトレイを開いておきます。(2. 項参照 )
(2) ディスクトレイを前方へ引き抜きます。
(組立時はスライドカムのボスとディスクトレイの溝が
合っているか確認してください。 )
8.4. トラバースユニット
(1) 天面側からのねじ 4 本とダンパー 4 個をはずします。
(2) a:トラバースユニットをはずします。
s : Special Screw (Rear)
p : DAMPER
8.5. メインシャーシ部の廃棄
(1) 底面からねじ 6 本をはずし、p:サブシャーシ (L)/(R) を
はずします。
(2) 天面からねじ 2 本をはずし、c:ローディングモーター
ass'y をはずします。
(3) 底面からねじ 1 本をはずし、c:SW 基板をはずします。
(4) スリットワッシャー3個をはずし、 ギア3個をはずします。
8.6. トラバース部の廃棄
(1) 天面からねじ 4 個をはずし、m:S. ティルトプレート、
p:S. ティルトベース、m:バネ 2 個、p:シャフトホ
ルダー ( 左右 ) をはずします。
(2) c:ピック ass'y から m:シャフト ( メイン )( サブ ) を
はずします。
(3) 底面からねじ 3 本をはずし、c:T/T モーター ass'y をは
ずします。
(4) スリットワッシャー 2 個をはずし、ギア 2 個をはずし
ます。
(5) 天面からねじ 2 本をはずし、c:Feed モーター ass'y を
はずします。
※ 下図や分解図を参照して分別廃棄して下さい。
m : Shaft (Main)/(Sub)
c : PU ass'y
s : Screw
p : Shaft holder(L/R)
m : Spring
c : T/T Motor ass'y
9
DVD-2910/955
2
a : Traverse unit
Boss ( ボス )
Ditch ( 溝 )
s : Screw
m : S. tilt plate
m : Spring
p : S. tilt base
p : Slit Washer
s : Screw
m : Pu chassis ass'y
s : Screw
c : Feed Motor ass'y
p : Gear