User Check List - Hoover Space Explorer User Manual

2. Remove the filter pack from the recess by pressing the button. [18]
Gently tap and wash the filter packs using hand warm water [19]. Remove excess
water from the filter with a dry cloth and leave to dry fully before re-using. [20]
Reassemble filter packs once fully dry and refit to the cleaner.
REMEMBER: Do not use hot water or detergents. In the unlikely event of the
filters becoming damaged, fit a Genuine Hoover replacement. Do not try and
use the product without a dust bag or filter fitted.
Cleaning the Permanent Dust Bag* (certain models only)
To maintain optimum performance we recommend that you wash the permanent dust bag
after every 5 full bags. Empty the contents of the Bag into a bin, wash the Bag under hand
warm water, remove excess water with a dry cloth and leave to dry fully before replacing.
Removing a blockage from the system
If the bag check indicator is red:
1. Check if the bag is full. If so, refer to 'Replacing The Dust Bag'.
2. If it is not full, then;
A. Do the filters need cleaning? If so, refer to 'Cleaning the Filter'.
B. Check if there is any other blockage in the system - Use a rod or a pole to
remove any blockage from telescopic tube or flexible hose.
C. Check for and clear any blockage in the Nozzle.
WARNING: - The bag check indicator will turn red if the cleaner is used when full, if there is a
blockage or if the filters are dirty. If the cleaner is used for a significant period of time with the
bag check indicator red, a thermal cut out will switch the cleaner off to prevent overheating. The
bag check indicator turn green once the cleaner has switched off to signal that the thermal cut
out has been activated. If this should happen, switch the cleaner off, unplug and correct the
fault. It will take about 45 minutes for the cut out to automatically reset.
ACCESSORIES AND NOZZLES
To obtain the best performance and energy efficiency
correct nozzles are used for the main cleaning operations. These nozzles are indicated
in the diagrams by the letters GP, HF or CA.
A nozzle type GP can be used to clean both carpet and hard floor.
A nozzle type HF is suitable for use only on hard floor.
A nozzle of type CA is suitable for use only on carpet.
The other nozzles are accessories for specialist cleaning tasks and are recommended
for occasional use only.
It is important to note that this vacuum cleaner is supplied with an Energy Label as required
by European Regulation (EU) 665/2013.
If the label shows a red prohibition circle on the left covering the carpet symbol, then this
#1
it is recommended that the
3
indicates that the vacuum cleaner is not suitable use on carpets.
If the label shows a red prohibition circle on the right covering the hard floor symbol, then
this indicates that the vacuum cleaneris not suitable for use on hard floors.
#1
Dust pick up ability carpet, dust pick up ability hard floor, and energy efficiency in ac-
NOTE:
cord with Commission Regulations (EU) 665/2013 and (EU) 666/2013.
Please see the model specification on the packaging label for inclusion of accessories to
individual models.
All accessories can be fitted to the hose handle or the end of the telescopic tube.
• 2 in 1 accessory – For corners and hard to reach areas and bookshelves, frames, keyboards
and other delicate areas [Q]. Remove the 2in1 accessory from the rear of the cleaner [11] and fit
onto the end of the handle. [12]
• Parquet Nozzle**– For parquet floors and other delicate floors. [Z1, Z2]
• Pet Hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep cleaning
on textile surfaces and other hard to clean areas. Particularly suitable for pet hairs removal. [W]
• Allergen Remover Mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for deep cleaning
on textile surfaces and other hard to clean areas. Particularly suitable for allergen removal. [X]
• Grand Turbo Nozzle* – Use the Grand Turbo Nozzle for deep cleaning on carpets. [Y]
IMPORTANT: Do not use the Grand Turbo Nozzle or Mini Turbo Nozzles on rugs with long fringes,
animal hides and carpet pile deeper than 15mm. Do not keep the nozzle stationary while the brush
is rotating.

USER CHECK LIST

should you have a problem with the product, complete this simple user checklist before
calling your local HOOVER service.
• Is there a working electricity supply to the cleaner? Please check with another
electrical appliance.
• Is the dust bag over-filled? Please refer to 'Cleaner Maintenance'.
• Is the filter blocked? Please refer to 'Cleaner Maintenance'.
• Is the hose or nozzle blocked? Please refer to 'Removing a blockage from the system'.
• Has the cleaner overheated? If so, it will take approximately 45 minutes for the cut
out to automatically reset.
•
IMPORTANT INFORMATION
HOOVER spares and Consumables
Always replace parts with genuine HOOVER spares. These are available from your local
HOOVER dealer or direct from Hoover. When ordering parts always quote your model number.
*Certain Models Only ** Certain models only, nozzles may vary according to model
GB