Related Manuals for Belkin Pre-N
Summary of Contents for Belkin Pre-N
-
Page 1: Adsl Modem
Network your computers and share your ADSL Internet access User Manual ADSL Modem with wireless Pre-N Router �� �� ������� ������ ����� �������� ��������������������� ������� �������������� ������� F5D8630-4A... -
Page 2: Table Of Contents
Benefits of a Home Network ......1 Advantages of a Belkin Wireless Network ....1 2 Make Sure You Have the Following . -
Page 3: Introduction
Introduction Thank you for purchasing the Belkin ADSL Modem with High-Speed Mode Wireless G Router (the Router). In minutes you will be able to share your Internet connection and network your computers with your new Router. The following is a list of features that make your Router an ideal solution for your home or small office network. -
Page 4: Make Sure You Have The Following
Make Sure You Have the Following Package Contents • MIMO ADSL Modem Router • RJ11 Telephone Cord - Gray • RJ45 Ethernet Networking Cable - Yellow • ADSL Microfilter* • Power Adapter • User Manual CD *ADSL microfilter varies by country. If it’s not included, you will need to purchase one. -
Page 5: Knowing Your Router
Knowing your Router The Router is designed to be placed on a desktop. All of the cables exit from the rear of the Router for better organization and utility. The LED indicators are easily visible on the front of the Router to provide you with information about network activity and status. - Page 6 Knowing your Router Knowing your Router WLAN Status LED The WLAN Status LED is solid GREEN when you enable the wireless LAN function. It flashes when the Router is transmitting or receiving data wirelessly. Green Green - blinking ADSL LED The ADSL LED flashes GREEN during negotiation with your ISP.
- Page 7 Knowing your Router Back Panel ����� DSL Line This port is for connection to your ADSL line. Connect your ADSL line to this port. Ethernet Ports The Ethernet ports are RJ45, 10/100 auto-negotiation. The ports are labeled 1 through 4. These ports correspond to the numbered LEDs on the front of the Router.
-
Page 8: Connecting Your Router
Connecting your Router Connecting your Router Positioning your Router Your wireless connection will be stronger the closer your computer is to your Router. Typical indoor operating range for your wireless devices is between 100 and 200 feet. In the same way, your wireless connection and performance will degrade somewhat as the distance between your Router connected devices increases. -
Page 9: Connecting Your Computers
Connecting your Router Connecting your Computers Power off your computers and networking equipment. Connect your computer to one of the rear of the Router labeled “connections to your computers” by using an Ethernet networking cable (one Ethernet network cable is supplied). YELLOW RJ45 ports on the... -
Page 10: Connecting Your Adsl Line
Connecting your Router Connecting your Router Connecting your ADSL Line Connection for the Router to the ADSL line varies by country and region. Typically it involves a microfilter or a microfilter with built-in splitter to allow simultaneous use of ADSL service and telephone service on the same telephone line. - Page 11 Connecting your Router Note: One RJ11 telephone cord is supplied. When inserting an RJ11 plug, be sure the tab on the plug clicks into position to ensure that it is properly seated. If you have a dedicated ADSL service telephone line with an RJ11 wall jack, simply connect a telephone cord from the wall jack to gray RJ11 port labeled “DSL line”...
-
Page 12: Powering Up Your Router
Connecting your Router Powering Up your Router Connect the supplied power adapter to the Router power-input plug labeled “Power”. Note: For safety and performance reasons, only use the supplied power adapter to prevent damage to the Router. After connecting the power adapter and the power source is turned on, the Router’s power icon take a few minutes for the Router to fully start up. -
Page 13: Setting Up Your Computers
Setting Up your Computers In order for your computer to properly communicate with your Router, you will need to change your computer’s “TCP/IP Ethernet” settings to “Obtain an IP address automatically/Using DHCP”. This is normally the default setting in most home computers. You can set up the computer that is connected to the ADSL modem FIRST using these steps. -
Page 14: Manually Configuring Network Adapters
You will also need to delete the Gateway address from the Gateway tab and DNS Configuration entries in order to properly be configured for connection to the Belkin router. Restart the computer. When the computer restarts, your network adapter(s) are now configured for use with the Router. - Page 15 Setting Up your Computers Set up the computer that is connected to the cable or DSL modem by FIRST using these steps. You can also use these steps to add computers to your Router after the Router has been set up to connect to the Internet.
- Page 16 Setting Up your Computers Setting Up your Computers If not already set, at “Configure:”, choose “Using DHCP Server”. This will tell the computer to obtain an IP address from the Router. Close the window. If you made any changes, the following window will appear.
- Page 17 Setting Up your Computers Manually Configuring Network Adapters in Mac OS X Click on the “System Preferences” icon. Select “Network” (1) from the “System Preferences” menu. Select “Built-in Ethernet” (2) next to “Show” in the Network menu.
- Page 18 Setting Up your Computers Setting Up your Computers Select the “TCP/IP” tab (3). Next to “Configure” (4), you should see “Manually” or “Using DHCP”. If you do not, check the PPPoE tab (5) to make sure that “Connect using PPPoE” is NOT selected.
-
Page 19: Recommended Web Browser Settings
Setting Up your Computers Recommended Web Browser Settings In most cases, you will not need to make any changes to your web browser’s settings. If you are having trouble accessing the Internet or the advanced web-based user interface, then change your browser’s settings to the recommended settings in this section. - Page 20 Setting Up your Computers Make sure there are no check marks next to any of the displayed options: “Automatically detect settings”, “Use automatic configuration script”, and “Use a proxy server”. Click “OK”. Then click “OK” again in the “Internet Options” page. Netscape Navigator 4.0 or Higher Start Netscape.
-
Page 21: Configuring Your Router With The Setup Wizard
Configuring your Router with the Setup Wizard Running the Setup Wizard You can access the web-based management user interface of the Router using the Internet browser on a computer connected to the Router. Type “192.168.2.1” (do not type in anything else such as “http://”... -
Page 22: Connecting To The Wireless Lan
Configuring your Router with the Setup Wizard Configuring your Router with the Setup Wizard The Setup Wizard will start automatically for express configuration (recommended) Click “Next” to continue. The first step is to select your country and ISP, and click “Next”. If your country and/or ISP is not listed, select “Other Country”... - Page 23 LAN settings: SSID = Belkin54g Note: Belkin strongly recommends that you enable wireless security to WEP or WPA and change SSID to something of your own. Please read the User Manual for details on levels of wireless security and how...
- Page 24 Configuring Your Router with the Setup Wizard Double-check the settings shown on the following screen. You can click “Back” to change the settings or click “Next” to confirm Note: You can always restart the Setup Wizard or use the Navigation Menu on the left to change your setting.
-
Page 25: Manually Configuring Your Router
Manually Configuring your Router Understanding the Web-Based User Interface The home page shows you a quick view of the Router’s status and settings. All advanced setup pages can be reached from this page. (10) Quick-Navigation Links You can go directly to any of the Router’s UI pages by clicking directly on these links. - Page 26 Manually Configuring your Router Manually Configuring your Router take you to a separate login page where you will need to enter a password. When you are logged into the Router, you can make changes to the settings. When you are finished making changes, you can log out of the Router by clicking the “Logout”...
-
Page 27: Changing Lan Settings
Manually Configuring your Router Changing LAN Settings All settings for the internal LAN setup of the Router can be viewed and changed here. Clicking on the header of the LAN tab tab’s header page. A quick description of the functions can be found here. - Page 28 Manually Configuring your Router Manually Configuring your Router LAN Settings IP Address The “IP address” is the internal IP address of the Router. The default IP address is “192.168.2.1”. To access the setup interface, type this IP address into the address bar of your browser.
- Page 29 IP address to change. Local Domain Name The default setting is “Belkin”. You can set a local domain name (network name) for your network. There is no need to change this setting unless you have a specific advanced need to do so. You can...
-
Page 30: Internet Wan
Manually Configuring your Router Manually Configuring your Router DHCP Client List You can view a list of the computers (known as clients), which are connected to your network. You are able to view the IP address the computer, the host name one), and the MAC address Card (NIC). - Page 31 Manually Configuring your Router Connection Type From the “Connection Type” page, you can select one of these five connection types based on the instruction provided by your ISP: • PPPoE • PPPoA • Dynamic IP (1483 Bridged) • Static IP (IPOA) •...
-
Page 32: Setting Your Isp Connection Type To Pppoe Or Pppoa
Manually Configuring your Router Manually Configuring your Router Setting your ISP Connection Type to PPPoE or PPPoA PPPoE (Point-to-Point Protocol over Ethernet) is the standard method of connecting networked devices. It requires a user name and password to access the network of your ISP for connecting to the Internet. - Page 33 Manually Configuring your Router Setting your Connection Type to Dynamic IP (1483 Bridged) This connection method bridges your network and ISP’s network together. The Router will obtain an IP address automatically from your ISP’s DHCP server. 1. VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) parameter here.
- Page 34 Manually Configuring your Router Manually Configuring your Router Setting your ISP Connection to Static IP (IPoA) This connection type is also called “Classical IP over ATM” or “CLIP”, which your ISP provides a fixed IP for your Router to connect to the Internet.
- Page 35 DNS (Domain Name Server) Settings A “Domain Name Server” is a server located on the Internet that translates Universal Resource Links (URLs) like “www.belkin.com” to IP addresses. Many ISPs do not require you to enter this information into the Router. The “Automatic from ISP” box if your ISP did not give you a specific DNS address.
-
Page 36: Wireless
Manually Configuring your Router Manually Configuring your Router Wireless The “Wireless” tab lets you make changes to the wireless network settings. From this tab, you can make changes to the wireless network name (SSID), operating channel, and encryption security settings. Channel and SSID 1. - Page 37 Manually Configuring your Router 2. Changing the Wireless Network Name (SSID) To identify your wireless network, a name called the SSID (Service Set Identifier) is used. The default SSID of the Router is “belkin54g”. You can change this to anything you want to or you can leave it unchanged. If there are other wireless networks operating in your area, you will want to make sure that your SSID is unique (does not match that of another wireless network in the area).
- Page 38 Manually Configuring your Router Manually Configuring your Router 4. Using the Wireless Mode Switch Your router can operate in either two different wireless modes: • 802.11b & 802.11g- Choose this option if you plan to have wireless clients of both 802.11b and 802.11g connect to your network. •...
- Page 39 Manually Configuring your Router Encryption/Security Securing your Wi-Fi Network Here are a few different ways you can maximize the security of your wireless network and protect your data from prying eyes and ears. This section is intended for the home, home office, and small office user.
- Page 40 Most of the new wireless equipment in the market today supports both 64-bit and 128-bit WEP encryption, but you might have older equipment that only supports 64-bit WEP. All Belkin wireless products will support both 64-bit and 128-bit WEP. Encryption Keys After selecting either the “64-bit”...
- Page 41 WPA (with radius server) With this system, a radius server distributes the Network key to the clients automatically. This is typically found in a business environment. For a list of Belkin wireless products that support WPA, please visit our website at www.belkin.com/networking.
- Page 42 Manually Configuring your Router Manually Configuring your Router Sharing the Same Network Keys Most Wi-Fi products ship with security turned off. So once you have your network working, you need to activate WEP or WPA and make sure your wireless networking devices are sharing the same Network key.
- Page 43 Manually Configuring your Router Using a Hexadecimal Key A hexadecimal key is a mixture of numbers and letters from A–F and 0–9. 64-bit keys are five two-digit numbers. 128-bit keys are 13 two-digit Characters. For instance: AF 0F 4B C3 D4 = 64-bit key C3 03 0F AF 0F 4B B2 C3 D4 4B C3 D4 E7 In the boxes below, make up your key by writing in two characters...
- Page 44 Manually Configuring your Router Manually Configuring your Router WEP Setup 64-Bit WEP Encryption Select “64-bit WEP” from the drop-down menu. After selecting your WEP encryption mode, you can enter your key by typing in the hex key manually. A hex (hexadecimal) key is a mixture of numbers and letters from A–F and 0–9.
- Page 45 Manually Configuring your Router 128-Bit WEP Encryption Select “128-bit WEP” from the drop-down menu. After selecting your WEP encryption mode, you can enter your key by typing in the hex key manually. A hex (hexadecimal) key is a mixture of numbers and letters from A–F and 0–9.
- Page 46 Manual’s publication, a security patch download is available free from Microsoft. This patch works only with the Windows XP operating system. You also need to download the latest driver for your Belkin Wireless G Desktop or Notebook Network Card from the Belkin support site.
- Page 47 Manually Configuring your Router Setting WPA-PSK (no server) From the “Security Mode” drop-down menu, select “WPA-PSK (no server)”. For Encryption Technique, select “TKIP” or “AES”. This setting will have to be identical on the clients that you set up. Enter your Pre-Shared key. This can be from eight to 63 characters and can be letters, numbers, or symbols.
- Page 48 Please Note: This section provides information on how to configure your Belkin Wireless G Network Cards to use security. At this point, you should already have your Wireless Router or access point set to use WPA or WEP. In order for you to gain a wireless connection, you will need to set your wireless notebook card and wireless desktop card to use the same security settings.
- Page 49 Manually Configuring your Router Connecting your Computer to a Wireless Network that Requires a 64-Bit or 128-Bit WEP Key Double-click the “Signal Indicator” icon to bring up the “Wireless Network” screen. The “Advanced” button will allow you to view and configure more options of your wireless card. Under the “Wireless Network Properties”...
- Page 50 Manually Configuring your Router Manually Configuring your Router Connecting your Computer to a Wireless Network that Requires WPA-PSK (no server) Double-click the “Signal Indicator” icon to bring up the “Wireless Network” screen. The “Advanced” button will allow you to view and configure more options of your wireless card.
- Page 51 Under the “Authentication” tab, select the settings that are indicated by your network administrator. Click “OK” to save the settings. Setting Up WPA for a Non-Belkin Wireless Desktop and Wireless Notebook Cards For non-Belkin WPA Wireless Desktop and Wireless Notebook Cards that are not equipped with WPA-enabled software, a file from Microsoft called “Windows XP Support Patch for Wireless Protected...
- Page 52 Manually Configuring your Router Manually Configuring your Router Important: You also need to ensure that the wireless card manufacturer supports WPA and that you have downloaded and installed the latest driver from their support site. Supported Operating Systems: Setting Up Windows XP Wireless Network Utility to Use WPA-PSK In order to use WPA-PSK, ensure you are using Windows Wireless Network Utility by doing the following: Under Windows XP, click “Start >...
-
Page 53: Wireless Bridge
Manually Configuring your Router Select “TKIP” or “AES” under “Data Encryption”. This setting will have to be identical to the Router that you set up. Type in your encryption key in the “Network Key” box. Click “OK” to apply settings. Wireless Bridge Wireless Bridging or Wireless Distribution System (WDS) is used to connect Wireless Routers and Access points together to extend a network. -
Page 54: Firewall
Manually Configuring your Router Manually Configuring your Router Wireless channels must match between Router and AP. Security settings (WEP) must match between Router and AP. If MAC filtering is enabled, user must be sure to add the WLAN MAC address(es) of the Router/AP in order to allow communication with each other. - Page 55 Manually Configuring your Router Virtual Servers Virtual servers allow you to route external (Internet) calls for services such as a web server (port 80), FTP server (Port 21), or other applications, through your Router to your internal network. Since your internal computers are protected by a firewall, machines from the Internet cannot get to them because they cannot be “seen”.
- Page 56 Manually Configuring your Router Manually Configuring your Router Client IP Filters The Router can be configured to restrict access to the Internet, email, or other network services at specific days and times. To restrict Internet access to a single computer for example, enter a name of the filter in “Filter Name”...
- Page 57 Manually Configuring your Router DMZ (Demilitarized Zone) If you have a client PC that cannot run an Internet application properly from behind the firewall, you can open the client up to unrestricted two-way Internet access. This may be necessary if the NAT feature is causing problems with an application such as a game or video conferencing application.
-
Page 58: Utilities
Manually Configuring your Router Manually Configuring your Router Utilities The “Utilities” screen lets you manage different parameters of the Router and perform certain administrative functions. Restart Router Sometimes it may be necessary to restart or reboot the Router if it begins working improperly. - Page 59 Manually Configuring your Router Restarting the Router to Restore Normal Operation Click the “Restart Router” button. The following message will appear. Click “OK” to restart your Router. Restore Factory Defaults Using this option will restore all of the settings in the Router to the factory (default) settings.
- Page 60 Manually Configuring your Router Manually Configuring your Router Saving/Backup Current Settings You can save your current configuration by using this feature. Saving your configuration will allow you to restore it later if your settings are lost or changed. It is recommended that you back up your current configuration before performing a firmware update.
- Page 61 Manually Configuring your Router When the save is complete, you will see the window below. Click “Close”. The configuration is now saved. Restore Previous Settings This option will allow you to restore a previously saved configuration. Click “Browse”. A window will open that allows you to select the location of the configuration file.
- Page 62 Manually Configuring your Router Manually Configuring your Router Firmware Update From time to time, Belkin may release new versions of the Router’s firmware. Firmware updates contain feature improvements and fixes to problems that may have existed. When Belkin releases new firmware, you can download the firmware from the Belkin update website and update your Router’s firmware to the latest version.
- Page 63 Manually Configuring your Router System Settings The “System Settings” page is where you can enter a new administrator password, set the time zone, enable remote management, and turn on and off the UPnP function of the Router. Setting or Changing the Administrator Password The Router ships with NO password entered.
- Page 64 Internet and get a response. You cannot set the clock yourself. Enabling Remote Management Before you enable this advanced feature of your Belkin Router, MAKE SURE YOU HAVE SET THE ADMINISTRATOR PASSWORD. Remote management allows you to make changes to your Router’s settings from anywhere on the Internet.
- Page 65 Click on the “Apply Changes” button to save your settings. Enabling/Disabling UPnP UPnP (Universal Plug-and-Play) is yet another advanced feature offered by your Belkin Router. It is a technology that offers seamless operation of voice messaging, video messaging, games, and other applications that are UPnP-compliant. Some applications require the Router’s firewall to be configured in a specific way to operate...
-
Page 66: Troubleshooting
Troubleshooting Troubleshooting Problem: The ADSL LED is not on. Solution: Check the connection between the Router and ADSL line. Make sure the cable from the ADSL line is connected to the port on the Router labeled “DSL Line”. Make sure the Router has power. The Power LED panel should be illuminated. - Page 67 Solution: If you are unable to connect to the Internet from a wireless computer, please check the following items: Look at the lights on your Router. If you are using a Belkin Router, the lights should be as follows: •...
- Page 68 Troubleshooting Troubleshooting Does the name of your wireless network appear in the results? Yes, my network name is listed—go to the troubleshooting solution titled “I can’t connect to the Internet wirelessly, but my network name is listed”. No, my network name is not listed—go to the troubleshooting solution titled “I can’t connect to the Internet wirelessly, and my network name is not listed”.
- Page 69 This setting is found on the Router’s wireless “Channel and SSID” configuration page. If you are still unable to access the Internet after completing these steps, please contact Belkin Technical Support. Problem: My wireless network performance is inconsistent. Data transfer is sometimes slow.
- Page 70 Problem: I am having difficulty setting up Wired Equivalent Privacy (WEP) security on a Belkin Router or Belkin Access Point. Solution Log into your Wireless Router or access point. Open your web browser and type in IP address of the Wireless Router or access point.
- Page 71 The “Advanced” button will allow you to view and configure more options of the Card. Once the “Advanced” button is clicked, the Belkin Wireless LAN Utility will appear. This Utility will allow you to manage all the advanced features of the Belkin Wireless Card.
- Page 72 Download the patch here: http://www.microsoft.com/downloads/details.aspx?FamilyID=009d8425-ce2b- 47a4-abec-274845dc9e91&displaylang=en You also need to download the latest driver for your Belkin Wireless 802.11g Desktop or Notebook Network Card from the Belkin support site. Other operating systems are not supported at this time. Microsoft’s patch only supports devices with WPA-enabled drivers such as Belkin 802.11g products.
- Page 73 Troubleshooting Problem: I am having difficulty setting up Wi-Fi Protected Access (WPA) security on a Belkin Wireless Router or Belkin Access Point for a home network. Solution: From the “Security Mode” drop-down menu, select “WPA-PSK (no server)”. For “Encryption Technique”, select “TKIP” or “AES”. This setting will have to be identical on the clients that you set up.
- Page 74 Troubleshooting Problem: I am having difficulty setting up Wi-Fi Protected Access (WPA) security on a Belkin Wireless Card for a home network. Solution: Clients must use the same key that the wireless router or access point uses. For instance if the key is “Smith Family Network Key” in the wireless router or access point, the clients must also use that same key.
- Page 75 Click “OK, then “Apply” to save the settings. Problem: I am having difficulty setting up Wi-Fi Protected Access (WPA) security and I am NOT using a Belkin Wireless Card for a home network. Solution: If you are NOT using a Belkin Wireless Desktop or Wireless Notebook Network Card and it is not equipped with WPA-enabled software, a file from Microsoft called “Windows XP Support Patch...
- Page 76 The most common wireless networking standard, 802.11b, transmits information at 11Mbps; 802.11a and 802.11g work at 54Mbps; and Pre-N works at 108Mbps. Pre-N, the precursor to the upcoming 802.11n release, promises speeds that exceed 802.11g, and up to twice the wireless coverage area. See...
- Page 77 Troubleshooting Wireless Comparison Chart Speed 11Mbps Common household devices such as cordless phones and microwave ovens may interfere with the unlicensed band 2.4GHz Compatible with 802.11g Depends on interference - typically 100–200 ft. indoors Mature – widely adopted 54Mbps 54Mbps Common household devices such as...
-
Page 78: Technical Support Information
Technical Support Information Technical Support Information Technical Support For latest software updates or if you have any further questions regarding installation of this product, please visit www.belkin.com/networking 877-736-5771 or 310-898-1100 ext. 2263 Europe: 00 800 223 55 460 Australia: 1800 235 546... -
Page 79: Appendixes
DNS is an acronym for Domain Name Server. A Domain Name Server is a server located on the Internet that translates URLs (Universal Resource Links) like www.belkin.com to IP addresses. Many ISPs do not require you to enter this information into the Router. If you... - Page 80 Appendixes Appendixes You have to double-click on a desktop icon other than your browser to get on the Internet. To set the Router to use PPPoE, type in your user name and password in the spaces provided. After you have typed in your information, click “Apply Changes”.
-
Page 81: Virtual Servers
It scans the air for any available network and allows each computer to automatically select a network from the survey. This occurs if the computer’s SSID is set to “ANY”. Your Belkin Router can block this random search for a network. If you disable the “ESSID Broadcast”... - Page 82 Appendixes Appendixes Client IP Filters The Router can be configured to restrict access to the Internet, email, or other network services at specific days and times. Restriction can be set for a single computer, a range of computers, or multiple computers. MAC Address Filtering The MAC address filter is a powerful security feature that allows you to specify which computers are allowed on the network.
-
Page 83: Administrator Password
Appendixes Administrator Password The Router ships with NO password entered. If you wish to add a password for more security, you can set a password from your Router’s web-based user interface. Keep your password in a safe place as you will need this password if you need to log into the Router in the future. - Page 84 Appendixes Appendixes UPnP UPnP (Universal Plug-and-Play) is a technology that offers seamless operation of voice messaging, video messaging, games, and other applications that are UPnP-compliant. Some applications require the Router’s firewall to be configured in a specific way to operate properly.
-
Page 85: Appendix B: Important Factors For Placement And Setup
To achieve the best wireless network coverage for your “wireless clients” (i.e., computers enabled by Belkin Wireless Notebook Network Cards, Wireless Desktop Network Cards, and Wireless USB Adapters): •... - Page 86 Experiment with more than one of the available channels, in order to find the clearest connection and avoid interference from neighboring cordless phones or other wireless devices. For Belkin wireless networking products, use the detailed Site Survey and wireless channel information included in your User Manual.
-
Page 87: Appendix C: Internet Connection Setting Table
These guidelines should allow you to cover the maximum possible area with your Wireless Router (or access point). Should you need to cover an even wider area, we suggest the Belkin Wireless Range Extender/Access Point. 5. Secure Connections, VPNs, and AOL Secure connections typically require a user name and password, and are used where security is important. - Page 88 Appendixes Country Connection Protocol Europe France PPPoE Germany PPPoE Holland 1483 Bridged PPPoA PPPoA PPPoE Belgium PPPoA Italy PPPoE or PPPoA Spain PPPoE or 1483 Bridged Sweden 1483 Bridged PPPoA Asia Australia PPPoE or PPPoA New Zealand PPPoE or PPPoA Singapore PPPoE VPI/VCI...
-
Page 89: Information
Information FCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY We, Belkin Corporation, of 501 West Walnut Street, Compton, CA 90220, declare under our sole responsibility that the product, to which this declaration relates, complies with Part 15 of the FCC Rules. Operation is... - Page 90 Modifications The FCC requires the user to be notified that any changes or modifications to this device that are not expressly approved by Belkin Corporation may void the user’s authority to operate the equipment. Canada-Industry Canada (IC) The wireless radio of this device complies with RSS 139 &...
- Page 91 Belkin Corporation Limited Lifetime Product Warranty Belkin Corporation warrants this product against defects in materials and workmanship for its lifetime. If a defect is discovered, Belkin will, at its option, repair or replace the product at no charge provided it is returned during the warranty period, with transportation charges prepaid, to the authorized Belkin dealer from whom you purchased the product.
- Page 92 Belkin Tech Support Europe: 00 800 223 55 460 © 2004 Belkin Corporation. All rights reserved. All trade names are registered trademarks of respective manufacturers listed. Apple, AirPort, Mac, Mac OS, and AppleTalk are trade- marks of Apple Computer, Inc., registered in the U.S. and other countries. The mark “Wi-Fi”...