Accessories; Maintenance - Lincoln Electric PANTHER K2874-2 Operator's Manual

PANTHER™ Push Pull Gun ACCESSORIES/MAINTENANCE

ACCESSORIES

The following accessories are available for the Panther™ push-pull
gun.
.035-3/64" Aluminum Drive Roll Kit
Features two grooves for feeding aluminum wire. The smaller
groove feeds .035 wire. The larger groove feeds 3/64th wire.
Order KP2876-1
1/16" Aluminum Drive Roll Kit
Features two grooves, each capable of feeding 1/16"
Aluminum wire
Order KP2876-2
Knurled Drive Roll Kit
For feeding steel wires or larger 5356 Aluminum wires
Order KP2911-1
Barrel Liner (45°, 60° Barrels)
Liner for feeding up to1/16" wire.
Order KP2879-1
Barrel Liner (180° Straight Barrel)
Liner for feeding up to1/16" wire.
Order KP2879-2
Gun Barrel
60 degree air-cooled gun barrel
45 degree air-cooled gun barrel
180 degree air-cooled gun barrel
60 degree water-cooled gun barrel
Cable Assemblies
15 foot Air-Cooled Cable Assembly - Panther
25 foot Air-Cooled Cable Assembly - Panther
50 foot Air-Cooled Cable Assembly - Panther
25 foot Water-Cooled Cable Assembly - Panther Order KP2884-2

MAINTENANCE

Safety Precautions
WARNING
WARNING
• Do not operate with covers
• Disconnect input power from
• Do not touch electrically hot
• Only qualified persons should
ELECTRIC SHOCK
can kill. ELECTRIC SHOCK
can kill.
When finished welding, be sure to turn power source off and close
valve on gas cylinder.
WARNING
• Working with flying or falling objects can cause serious eye
injuries.
• Protective eyeware such as safety specticals with side
shields or goggles must be worn at all times.
FLYING FRAGMENTS
FLYING FRAGMENTS
can cause eye injury.
can cause eye injury.
(consult Lincoln Sales Bulletin E12.16)
Order KP2877-60
Order KP2877-45
Order KP2877-180
Order KP2878-60
Order KP2883-1
Order KP2883-2
Order KP2883-3
removed.
welder before installing gun.
part.
install, use or service this
machine.
Wire Conduits for Aluminum Wire
15 foot .035"-1/16" Wire Diameter
25 foot .035"-1/16" Wire Diameter
50 foot .035"-1/16" Wire Diameter
Wire Conduits for Steel Wire
15 foot .035"-1/16" Wire Diameter
25 foot .035"-1/16" Wire Diameter
50 foot .035"-1/16" Wire Diameter
Gas Diffuser
Diffuser designed to accept thread on gas nozzles
Order KP2746-1
Gun Tube Insulator
For insulation of gas nozzle
Gas Nozzle
.50 Thread on Nozzle (Tip Recessed)
.62 Thread on Nozzle (Tip Recessed)
Contact Tips
.035
3/64"
1.
3/64" (5356)
1/16"
Air-Cooled to Water Cooled Retrofit 25'
Cable Assembly 25' Water Cooled
Gun Barrel
1.
For use on lower amperage applications with 5356 wire. Features a smaller
tip inner diameter to reduce arc flaring.
Routine Maintenance
Periodically blow out or vacum any metal wire shavings from Drive
Roll area.
Inspect and replace any worn wire on inlet guide or barrel liner.
NOTE: Oil and spray cleaners can contaminate electrode wire and
cause bad welds. They could also make wire drive rollers slip. Be
careful when using any of these liquids on push-pull gun.
Carefully clean gun with a cleaner that is safe for plastic. Apply
cleaner to rag and wipe gun. Do NOT spray cleaner on gun. Keep
cable dean. Oil, grease gasoline, paint, and solvents degrade cable
insulation.
Routine maintenance for consumable spare parts will depend on Duty Cycle and
particular application.
8
Order KP2881-15
Order KP2881-25
Order KP2881-50
Order KP2912-15
Order KP2912-25
Order KP2912-50
Order KP2773-2
Order KP2742-1-50R
Order KP2742-1-62R
Order KP2744-035A
Order KP2744-364A
Order KP2744-364A5356
Order KP2744-116A
Order KP2884-2
Order KP2878-60