Integrated Pump Maintenance (Optional With Pump Package); Capacities - Trane Sintesis RTAF HE series Installation Operation & Maintenance

Integrated Pump Maintenance
Water Pump Maintenance
CAUTION! The lifting eyebolts of the motor are suitable
for the weight of the motor only. It is not allowed to carry
FWD
the complete pump on the lifting eyebolts of the motor.
Power supply

Capacities

Motor
Cooling capacity on water (1)
Heating capacity on water (2)
Fan motor
Check the motor at regular intervals. It is important
Fan power input (3)
to keep the motor clean in order to ensure adequate
Current amps (3)
ventilation. If the pump is installed in a dusty
Start-up amps
environment, both pump and motor must be cleaned Air flow
minimum
and checked regularly.
nominal
maximum
Lubrication
Main coil
Water entering/leaving connections
The pump shaft seal does not require any special
Electric heater (accessory for blower only)
maintenance. Visual leakage check are however required.
Electric power supply
Distinctly visible leakage will require an exchange of the
Heating capacity
seal.
Hot water coil (accessory for blower only)
Heating capacity (4)
G2 filter (filter box accessory)
The bearing of motors must be greased at the shortest
Quantity
period (4000 hours , maintenance nameplate or yearly
Dimensions ( LxWxth)
service). The required grease quantity is 10g per bearing.
G4 filter (filter box accessory)
Quantity
The motor must run during lubrication.
Dimensions ( LxWxth)
Condensate pump (accessory)
Use lithium-based grease.
Water flow - lift height
Not available for FWD30 and FWD45
Sound level (L/M/H speed)
For further details about pump maintenance please
Sound pressure level (5)
consult the pump supplier website.
Sound power level (5)
Unit dimensions
Width x Depth
Figure 41 – Motor bearings
Height
Shipped unit dimensions
Width x Depth
Height
Weight
Colour
Recommended fuse size
Unit alone (aM/gI)
Unit with electric heater (gI)
(1) Conditions: Water entering/leaving temperature: 7/12 °C, Air inlet temperature 27/19°C DB/WB - Nominal air flow
(2) Conditions: Water entering/leaving temperature: 50/45 °C, Air inlet temperature 20°C DB - Nominal air flow
(3) At high speed with nominal air flow.
(4) Water entering/leaving temperature 90/70 °C, air inlet temperature 20 °C DB, Nominal air flow.
(5) A rectangular glass wool duct 1m50 long is placed on the blower.The measurement is taken in the room containing the blower unit.
Heat exchanger operating limits:
FWD:
*water temperature: max 100° C
*absolute service pressure: min 1 bar/max 11 bars
Accessories - Hot water coil:
*water temperature: min. +2° C/max. 100° C
*absolute service pressure: min 1 bar/max 11 bars
4 172
Technical Data
08
(V/Ph/Hz)
(kW) 5,2
(kW) 6,3
(type)
(kW) 0,23
(A) 1,1
(A) 3,2
(m /h) 490
3
(m /h) 820
3
(m /h) 980
3
(type)
(Dia) 3/4"
(V/Ph/Hz) 230/1/50
(kW) 2/4
(kW) 6,3
2
(mm) 386x221x8
-
(mm) -
(type)
(l/h - mm)
(dB(A)) 36/40/43
(dB(A)) 46/50/53
(mm) 890 x 600
(mm) 250
(mm) 933 x 644
(mm) 260
(kg) 32
(A) 8/16
(A) 16 (2kW),25 (4kW)
(Optional with Pump Package)
12 20
230/1/50
8,3 15
11,9 18,9
2 x direct drive centrifugal
0,46 0,65
2,2 3,1
5,5 9,3
980 1400
1650 2300
1970 2600
ISO R7 rotating female
3/4" 1 1/2"
230/1/50 or 400/3/50 400/3/50
8 10
12 17,4
2 2
486x271x8 586x321x8
2 2
486x264x48 586x314x48
Centrifugal
24 - 500
38/41/44 46/50/53
48/51/54 56/60/63
1090 x 710 1290 x 820
300 350
1133 x 754 1333 x 864
310 360
46 61
galvanised steel
8/16 8/16
40 (230V),3*16 (400V) 3*20
30 45
18,8 30,1
20,9 38,2
1,04 1,51
4,7 5,5
14,1 16,5
1800 2700
3000 4500
3600 5400
1 1/2" 1 1/2"
400/3/50 400/3/50
12 12
22,4 34,5
2 2
586*421*8 586*621*8
2 2
586*414*48 586*614*48
47/52/57 47/52/58
57/62/67 57/62/68
1290 x 970 1290 x 1090
450 650
1333 x 1008 1333*1133
460 660
76 118
8/25 8/25
3*25 3*25
UNT-PRC002-GB RLC-SVX19G-GB