Advertisement
Quick Links
U.S. AND CANADA CALL: TOLL FREE 1-800-225-3958
UNCRATING AND INSPECTION
ASSEMBLY AND INSTALLATION
FRONT BEARING ASSEMBLY
COOKING PROCEDURES
CLEANING PROCEDURES
TROUBLESHOOTING GUIDE
MAINTENANCE PROCEDURES
PARTS LIST
OPTIONAL FEED TRAY
DRIVE SYSTEM
HEATER TUBE INSTALLATION
COMPONENT ARRANGEMENT
HEAT REFLECTOR/CRUMB TRAY
WIRING DIAGRAM
REINSTALLING TOP COVER
FILE:F\USERS\BOB/MANUALS\VAMUAL\EZ10
HG0126
OPERATOR'S MANUAL
HOLMAN CONVEYOR TOASTERS
OVEREASY MODEL EZ10
FOR SERVICE INFORMATION
24 HOURS/DAY 7 DAYS/WEEK
TABLE OF CONTENTS
DRAWINGS
PAGE 1
PAGE 1
PAGE 1a
PAGE 2
PAGE 3
PAGE 4, 5
PAGE 5, 6
PAGE 7
PAGE 3
PAGE 4
PAGE 5
PAGE 7
PAGE 7
PAGE 8
PAGE 9
REVISED 07/25/00 RRD
Advertisement
Related Manuals for Holman EZ10
Summary of Contents for Holman EZ10
- Page 1 OPERATOR'S MANUAL HOLMAN CONVEYOR TOASTERS OVEREASY MODEL EZ10 FOR SERVICE INFORMATION U.S. AND CANADA CALL: TOLL FREE 1-800-225-3958 24 HOURS/DAY 7 DAYS/WEEK TABLE OF CONTENTS UNCRATING AND INSPECTION PAGE 1 ASSEMBLY AND INSTALLATION PAGE 1 FRONT BEARING ASSEMBLY PAGE 1a...
-
Page 2: Uncrating And Inspection
OPERATOR'S MANUAL HOLMAN CONVEYOR TOASTERS OVEREASY MODEL EZ10 UNCRATING AND INSPECTION Unpack unit and components from container. Remove all visible packing material, inspect unit for damage. If damage is discovered, file a claim immediately with the carrier that handled the shipment. - Page 3 MODEL EZ10 SPRING LOADED FRONT BEARING ASSEMBLY Your Holman Conveyor Toaster is equipped with a spring-loaded front bearing assembly as shown below in fig. 1. The spring-loaded bearing assembly keeps the conveyor belt at a constant tension as the unit heats up and cools down. The conveyor belt is set to the proper tension when the white teflon bushing is flush with the end of the extension as shown in fig.
- Page 4 OVEREASY MODEL EZ10 COOKING PROCEDURES A. BREAD TOASTING LIGHTER DARKER LIGHT TO DARK CONTROL ON/OFF SWITCH 1. Switch On/Off switch control to the ON position; turn light to dark control to the center of the dial. 2. Allow warm up time of 5 to 10 minutes.
-
Page 5: Cleaning Procedures
CRUMB TRAY SLIDES BENEATH CONVEYOR BELT NOTE: LUBRICATION OF DRIVE CHAIN WITH A GRAPHITE BASED LUBRICANT IS REQUIRED AS PERIODIC MAINTENANCE. CALL HOLMAN FACTORY SERVICE DEPARTMENT FOR DETAILS. REVISED 1/16/97 MJC Page 3 OPERATOR'S MANUAL HOLMAN CONVEYOR TOASTERS OVEREASY MODEL EZ10... - Page 6 2. Check to see if the toaster is plugged in and all controls are turned to the ON position. B. UNIT HAS HEAT ONLY ON ONE SIDE, CONVEYOR BELT TURNS FREELY. 1. Call Holman Factory Service Department at 1-800-225-3958 as heating element may need replacing. C. CONVEYOR BELT DOES NOT TURN, HEATER TUBES GET HOT.
-
Page 7: Maintenance Procedures
TROUBLE SHOOTING GUIDE (CON'T) D. CONVEYOR BELT RUNS AT ONE SPEED REGARDLESS OF SPEED CONTROL SETTING. 1. Call Holman Factory Service Department at 1-800-225-3958 as speed control should be replaced. MAINTENANCE PROCEDURES A. CONVEYOR BELT AND DRIVE MOTOR DO NOT REQUIRE LUBRICATION. - Page 8 DRIVE CHAIN SIDE PANEL DRIVE SPROCKET DRIVE MOTOR LUBRICATION OF DRIVE CHAIN WITH A GRAPHITE BASED LUBRICANT IS REQUIRED AS PERIODIC MAINTENANCE. CALL HOLMAN FACTORY SERVICE DEPARTMENT FOR DETAILS. Page 6 REV. 12/23/96 MJC OPERATOR'S MANUAL HOLMAN CONVEYOR TOASTERS OVEREASY MODEL EZ10...
- Page 9 INSTRUCTIONS FOR REINSTALLING THE TOP COVER ON THE OVEREASY POSITION THE TOP COVER AS SHOWN ALIGN THE LIP OF THE TOP COVER UNDER THE SLOT IN FRONT OF UNIT SLIDE COVER TOWARD BACK OF UNIT AS FAR AS POSSIBLE LOWER THE REAR OF THE TOP COVER DOWN OVER THE BACK OF THE UNIT AND SECURE WITH THE SCREWS PROVIDED.
- Page 10 WIRING DIAGRAM FOR MODEL EZ10 120 VOLT, 60Hz SINGLE PHASE CONVEYOR MOTOR SPEED CONTROL MOTOR PLUG CONFIGURATION GROUND NEMA 5-15P 120V REV. 11/15/99 REV.12/1/99 MJC PAGE 8 OPERATOR'S MANUAL HOLMAN CONVEYOR TOASTERS MODEL EZ10...
- Page 13 H:\Y2KWDIAG\010533.DWG, 12/16/2003 02:27:20 PM...
- Page 14 MOTOR, 2020 BB REVERSED, FAN BLADE NOT INCLUDED 2U-200511 2R-200721 FAN BLADE 2P-200645 SPROCKET, 25B17 X 5/16 HN-401566 PANEL, SIDE & BACK, EZ10 HA-115383 BLOCK, TERMINAL 3 POS, SM 2P-200665 CHAIN, 17 1/2 INCH HN-115140 2P-200645 SPROCKET, 25B17 X 5/16...