Sears 200.71450 Owner's Manual
  1. Manuals
  2. Brands
  3. Sears Manuals
  4. Battery Charger
  5. 200.71450
  6. Owner's manual
Sears 200.71450 Owner's Manual

Sears 200.71450 Owner's Manual

50/15/2 amp manual battery charger 225/125 amp engine starter with battery tester
Hide thumbs
Table of Contents

Advertisement

Quick Links

OWNER'S
MANUAL
Model No.
200.71450
50/15/2 AMP
MANUAL BATTERY
CHARGER
225/125 AMP
CAUTION:
ENGINE STARTER with
Read and Follow All Safety
BATTERY TESTER
Rules and Operating Instructions
Before Every Use of this Product.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Advertisement

Table of Contents
loading

Related Manuals for Sears 200.71450

Summary of Contents for Sears 200.71450

  • Page 1 Model No. 200.71450 50/15/2 AMP MANUAL BATTERY CHARGER 225/125 AMP CAUTION: ENGINE STARTER with Read and Follow All Safety BATTERY TESTER Rules and Operating Instructions Before Every Use of this Product. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

  • Page 2: Table Of Contents

    FULL THREE-YEAR WARRANTY If, within three years from the date of purchase this battery charger fails due to a defect in materials or work- manship, simply RETURN IT TO THE NEAREST SEARS STORE IN THE UNITED STATES, and Sears will repair or replace it, free of charge.

  • Page 3: Important Safety Instructions

    This may spark or short circuit the battery or another electrical device that may cause an explosion. • Always operate your battery charger in an open, well ventilated area. • Never smoke or allow a spark or flame in the vicinity of the battery or engine.

  • Page 4: Parts

    Parts This section shows an illustration of your battery charger. Use it to become familiar with where all the parts are located, and what they look like. Replacement Parts List Sears 71450 Item Description Handle Negative (BLK) cable w/clamps Positive (RED) cable w/clamps...

  • Page 5: Before Using Your Battery Charger

    Before Using Your Battery Charger It is important to prepare your charger for use. This section will tell you how to assemble the charger, ground and connect the power cord, and prepare to charge a battery. Assembling your charger It is important to fully assemble your charger before use.

  • Page 6: Plugging It In

    3. Tap the other axle cap onto the opposite end of the axle and place the axle assembly onto the bottom of the charger. Place one end of the bracket into slot, then place the axle assembly under each bracket. Fasten the other side of the brackets using the two 10-32 screws provided.

  • Page 7: Using An Extension Cord

    A TEMPORARY adapter may be used to connect the charger to a two-pole outlet if a properly grounded outlet is not available. Use the adapter ONLY until a properly grounded outlet can be installed by a qualified electrician. DANGER: Before using an adapter as illustrated, be certain that the center screw of the outlet plate is grounded.

  • Page 8: Preparing Your Battery To Be Charged

    Preparing your battery to be charged It is important that you read and follow these guidelines while you are preparing to charge your battery. • Make sure that you have a 12 volt or 6 volt lead-acid battery. Set the volt/amp selector switch to match the voltage rating of the battery to be charged.

  • Page 9: Using Your Battery Charger

    Using Your Battery Charger To obtain the best results from your battery charger, you must know how to use it properly. This section will tell you how to set the controls, and how you can charge a battery while it is still in the vehicle, or you can remove it and then charge it.
  • Page 10 The “START” area of the ammeter indicates a high rate of current being drawn by the battery. For example, when cranking an engine, the needle will be at the far right side of the “START” area since the starter will be drawing up to 225 amps from the charger.

  • Page 11: Charging Your Battery

    OFF position, then unplug the charger power cord. Stand away from battery and remove the charger clamps from the NEGATIVE end of the cable first, then from the POSITIVE post. 12. Clean and store the battery charger in a dry location. Sch 517 NEGATIVE GROUNDED SYSTEM...
  • Page 12 OFF position, then unplug the charger power cord. Stand away from battery and remove the charger clamps from the NEGATIVE end of the cable first, then from the POSITIVE post. 11. Clean and store the battery charger. Sch 517...

  • Page 13: Calculating Charge Time

    Calculating charge time The Chart Method Use the following table to more accurately determine the time it will take to bring a battery to full charge. First, identify where your battery fits into the chart. • Small batteries — motorcycles, garden tractors, etc. —...

  • Page 14: Using The Engine Start Feature

    Using the engine start feature Your battery charger can be used to jump start your car if the battery is low. Follow these instructions on how to use the engine start feature. 1. Set the timer knob to the OFF position. Then follow the instructions for how to connect the charger to the battery in the section “Charging your battery...

  • Page 15: Troubleshooting

    Circuit breaker cycles when current draw is too high. Separate the clamps. Check for worn cables and replace if needed. Have a Sears technician test the battery. Correct connections. Correct Volt/Amp Selector setting. Crank time varies with the amount of current drawn. If cranking draws more than 225 amps, crank time may be less than 5 seconds.
  • Page 16 For the repair or replacement parts you need Call 7 am - 7 pm, 7 days a week 1-800-366-PART (1-800-366-7278) For the location of a Sears Repair Service Center in your area Call 24 hours a day, 7 days a week 1-800-488-1222...

Table of Contents